CAB 4712 Operator's Manual
Flag applicator
Hide thumbs
Also See for 4712:
- Service manual (53 pages) ,
- Assembly instructions manual (30 pages) ,
- Service manual (43 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CAB 4712
Summary of Contents for CAB 4712
- Page 1 Operator's Manual 4712 Flag Applicator Made in Germany...
- Page 2 Edition: 07/2017 - Part No. 9009954 Copyright This documentation as well as translation hereof are property of cab Produkttechnik GmbH & Co. KG. The replication, conversion, duplication or divulgement of the whole manual or parts of it for other intentions than its original intended purpose demand the previous written authorization by cab.
-
Page 3: Table Of Contents
Table of Contents Introduction ............................4 Instructions ............................... 4 Intended Use ............................4 Safety Instructions ............................ 4 Safety Markings ............................5 Environment ............................. 5 Product Description ..........................6 Important Features ........................... 6 Technical Data ............................6 Product Overview ............................. 7 Contents of Delivery .......................... -
Page 4: Introduction
• The device applicator mounted on a cab printer of the Hermes+ series is intended exclusively for applying suitable materials that have been approved by the manufacturer. Any other use or use going beyond this shall be regarded as improper use. -
Page 5: Safety Markings
Introduction • Before mounting the delivered components disconnect the printer from the power supply and close the shutoff valve of the applicator. • Only connect the device to other devices which have a protective low voltage. • Switch off all affected devices (computer, printer, accessories) before connecting or disconnecting. •... -
Page 6: Product Description
(Ø) x π Front Diameter x Pi Rear Flag length L Flag length L Label transfer Label type 4712 L 300 Label width Hermes + 4 60 -100 Label height 10 - 50 Ø 3 - 20 Diameter Working pressure... -
Page 7: Product Overview
Product Description Product Overview Fig. 2 Product Overview 1 Cover 5 Short stroke cylinder - tamp group 2 Compressed air connector 6 Tamp group 3 Shutoff valve 7 Tamp 4 Main stroke cylinder 8 Blow tube... -
Page 8: Contents Of Delivery
Product Description Contents of Delivery 1 Applicator with mounted tamp assembly 2 Blow tube for supporting air (depend of the used printer) 3 Documentation Fig. 3 Content of Delivery Note! Please keep the original packaging in case the applicator must be returned. Attention! The device and printing materials will be damaged by moisture and wetness. -
Page 9: Operation
Operation Standard Operation Check all external connections. Load the material. Ensure that the locking system is locked "Operator's Manual" of the printer. Open the shutoff valve. Attention! Ensure that the pad is not covered by a label when switching on the printer-applicator system. Otherwise the vacuum sensor may not be calibrated correctly. - Page 10 Operation Fig. 5 Mounting & dismounting the applicator on the printer Attention! Initiation, adjustments and changing of parts is to be performed by qualified service personnel only. Service Manual Applicator Attention! Disconnect the printer from the power supply before mounting the applicator! ...
-
Page 11: Error Messages
Error Messages Error Messages of the Printer For detailed information about printer errors (e.g. 'Paper out', 'Ribbon out', etc.) Check the operator's manual of the printer. Error treatment: Clearing the error results. Press the feed key to synchronize the label feed, remove the left over labels manually. ... -
Page 12: Licenses
Person authorised to compile the technical file: Erwin Fascher Am Unterwege 18/20 99610 Sömmerda Signed for, and on behalf of the Manufacturer: Sömmerda, 19.06.2017 cab Produkttechnik Sömmerda Gesellschaft für Computer- und Automationsbausteine mbH Erwin Fascher 99610 Sömmerda Managing Director The product must not be put into service until the final machinery into which it is to be incorporated has been declared in conformity with the provisions of the Directive on machinery. -
Page 13: Eu Declaration Of Conformity
Directive 2011/65/EU on the restriction of the use of certain • EN 50581:2012 hazardous substances in electrical and electronic equipment: Signed for, and on behalf of the Manufacturer: Sömmerda, 19.06.2017 cab Produkttechnik Sömmerda Gesellschaft für Computer- und Automationsbausteine mbH Erwin Fascher 99610 Sömmerda Managing Director...
Need help?
Do you have a question about the 4712 and is the answer not in the manual?
Questions and answers