Related Manuals for daviteq WS433-M12F-ATE
Summary of Contents for daviteq WS433-M12F-ATE
- Page 1 Sub-Ghz Wireless Ambient Temperature Sensor WS433-M12F- USER GUIDE FOR WIRELESS AMBIENT TEMPERATURE SENSOR WS433-M12F-ATE...
- Page 2 USER GUIDE FOR WIRELESS AMBIENT TEMPERATURE SENSOR WS433-M12F-ATE WS433-M12F-ATE-MN-EN-01 FEB-2020 This document is applied for the following products WS433-M12F-ATE HW Ver. FW Ver. 5.04 Wireless Sensor Transmitter 433Mhz, compatible with all DULP sensor Item Code WS433-M12F modules, AA 1.5VDC battery, IP67...
- Page 3 3. Specification SENSOR SPECIFICATION : Digital type, factory calibrated, IP67, immersible to ice- Sensor water for quick validation Measuring range -35 .. + 70 oC Accuracy & Resolution +/- 0.5oC, 0.125oC Material PA plastic with PVC cable Electrical connection M12-male connector WIRELESS SPECIFICATION : Data speed Up to 50kbps...
-
Page 4: Product Pictures
Net weight (without battery) < 60g Box dimension 190x50x50mm Gross weight 100g 4. Product Pictures... -
Page 5: Operation Principle
5. Operation principle Process of measurement When the sensor sampling time interval is reached, for example 2 minutes, the node will wake up and switch ON the power supply to supply the energy to external sensor to start the measurement. Depends on the type and characteristic of external sensor, the sensor will take a certain time to finish the measurement. - Page 6 a: constant (default value is 1) b: constant (default value is 0) So, if there is no user setting for a and b ==> Y = X The Y value will be compared with Lo and Hi threshold. Status bytes of sensor Node Hi-Byte is error code Error code Description...
-
Page 7: Mounting Bracket Installation
Take off the sensor cover like Step 1 and press the button until you see LED flashes 2 times for 625 kps option 6.3 Wireless sensor configuration with co-ordinator You can configure the wireless sensor with the co-ordinator by following the steps in the link below: http://www.daviteq.com/en/manuals/books/long-range-wireless-co-ordinator-ws433-cl/page/user-guide- for-long-range-wireless-co-ordinator-ws433-cl 7. Installation 7.1 Mounting bracket installation... -
Page 8: Installation Location
The mounting bracket is made from hard metallic material. The following steps are for mounting this bracket; 7.2 Installation location The bracket will be fixed on the wall or surface by 2 x M4 screws (supplied by customer) or double-sided 3M tape (included in accessory bag in carton box);... - Page 9 7.3 IO Wiring & Sensor installation The sensor module has M12-male connector which is matched with M12-female connector on wireless module; Carefully plug the sensor module onto wireless module, using HAND to tighten slowly until stop; Note: please DO NOT over tightening by hand or other tool, it can damages the M12 connector;...
- Page 10 Steps for battery installation: Using Philips screw driver to unscrew M2 screw at the side of housing Carefully pull out the top plastic housing in the vertical direction...
- Page 11 NOTE: Because of O-ring, it requires to have much pulling force at the beginning, therefore please do it carefully to avoid the damage of circuit board which is very thin (1.00mm); Insert the AA battery, please take note the poles of battery...
- Page 12 Insert the top plastic housing and locking by M2 screw...
-
Page 13: Troubleshooting
Mobile : +012-376 7181 Email: contact@templogger.net Fax : +603-4143 3388 Manufacturer Dai Viet Controls & Instrumentation Company Ltd. No.11 Street 2G, Nam Hung Vuong Res., An Lac Ward, Binh Tan Dist., Ho Chi Minh City, Vietnam. Tel: +84-28-6268.2523/4 (ext.122) Email: info@daviteq.com | www.daviteq.com...