Page 1
USER GUIDE FOR WIRELESS ACTIVE TAG 433MHZ WS433-TAG WS433-TAG-MN-EN-01 DEC-2020 This document is applied for the following products WS433-TAG-01 WS433-TAG HW Ver. FW Ver. Item Code WS433-TAG-01 WIRELESS ACTIVE SENSOR TAG 433MHZ, AA 1.5-3.6VDC BATTERY, IP67, C/W STEEL BRACKETS WS433-CL-07 WS433-CL HW Ver.
Page 2
1. Functions Change Log Product HW Ver. FW Ver. Release Date Functions Change Change RF data WS433-TAG-01 DEC-2019 rate by button 2. Specification of SENSOR TAG, WS433- TAG-01 Data speed Up to 50kbps Antenna Internal Antenna 01 x AA 1.5 - 3.6VDC, working time up to 10 years (depends on...
RF frequency band datasheets) ETSI EN 300 220, EN 303 204 (Europe) FCC CFR47 Part15 (US), ARIB Ready to comply STD-T108 (Japan) Vietnam Type Approval Certification QCVN 73:2013/BTTTT, QCVN 96:2015/BTTTT (DAVITEQ B00122019) Security Standard AES-128 Operating temperature -40oC..+85oC Housing Poly-carbonate, IP67...
Page 4
Step 1: Open the sensor cover with a Phillips screwdriver; Step 2: Insert 01 x AA 1.5 or 3.6VDC battery, please take note of the poles of the battery; ATTENTION: REVERSED POLARITY OF BATTERY IN 10 SECONDS CAN DAMAGE THE SENSOR CIRCUIT!!!
(frequency, RF output power, data rate), if held for more than 30 seconds then the button function does not work. Reset default WS433: Frequency: 433.92 MHz RF transmit power: -10 dBm RF data rate: 50 kbps 4.3 Modbus register of WS433-TAG-01...
Page 6
- When [error code] = 1 means that WS433-CL-07 has no wireless sensor tag connected yet. - When the WS433-CL-07 is not connected to the WS433-TAG, if there is a sensor tag nearby, it will sends all 3 packets with RSSI > RSSI threshold, the WS433-CL-07 receives that sensor tag and [error code] = 0, the buzzer of WS433- CL-07 will beep once.
Page 7
Green: White: The signal cable from the sensor should be protected by a corrugated hose or the Φ16 protection tube, keep the cable avoid high-temperature areas. 5.2 Hall sensor and button function Button and Hall sensor (using magnets for activation) have the same function and are only available for the first 5 minutes after power on.
Page 8
[\r\n] for ending, Enter and new line For Example: 1. Wireless tag for trailer WS33-TAG: DV,15,020201112,99,2,0,00000000,00000000,ED\r\n Description Explain wireless tag for trailer WS433-TAG 020201112 ID Sensor tag % sensor battery RF signal strength No error 00000000 → not used for this sensor 00000000 →...
1 and value 2 are Float. checksum 6. Installation All the device such as WS433-TAG-01 and WS433-CL-07 should be fixed on trailers or tractors with screws; ATTENTION: DO NOT install the Wireless sensor tag inside a completed metallic box or housing, because the RF signal can not pass through the metallic material.
Check that the battery is No power supply; empty or not installed Wireless sensor WS433-TAG not The distance was too far correctly; connected to WS433-CL-07 beyond 3 meters. Reinstall sensor within 3- meter distance. No power supply; Check the power supply;...