Labels & Cosmetics - Grizzly G0725 Owner's Manual

REF PART # DESCRIPTION
105 P0725105 SWITCH MOUNTING PLATE
106 P0725106 RIGHT RUBBER FOOT
107 P0725107 LEFT RUBBER FOOT
108 P0725108 GUARD PLATE
109 P0725109 CUTTERHEAD COVER
110 P0725110 PHLP HD SCR M5-.8 X 6
111 P0725111 CAP SCREW M6-1 X 8
121
Failure to keep hands clear of cutterhead
may result in serious personal injury.
120V3
MODEL G0725
6" JOINTER
Specifications
WARNING!
Motor: 1-1/2 HP, 110V, 1-Ph, 60 Hz To reduce the risk of serious injury when using this machine:
1. Read & understand owner's manual before operating.
Full-Load Amp Draw: 12A
2. Always wear approved eye protection and respirator.
Cutterhead: 2 Knife, 1-7/8" Dia.
3. Always keep all guards in place and in proper operating
Replacement Knives: H9837
condition.
Knife Size: 6-1/2" x 7/8" x 3/32"
4. Never perform jointing or planing cuts on pieces
Maximum Depth of Cut: 1/8"
smaller than 8" long, 3/4" wide, or 1/4" thick.
Cutterhead Speed: 10,000 RPM
5. Always use push blocks when face planing.
Cuts Per Minute: 20,000
6. Keep hands at least 12" away from cutterhead.
Fence Tilt: 45º, 90º, 135º 7. Never cut deeper than 1/8" on a single pass.
8. Do not wear loose clothing, gloves, jewelry, or other items
Table Size: 6-1/4" x 28-1/2"
that can get entangled. Tie back long hair and roll up
Weight: 76 Lbs.
sleeves.
9. Turn motor OFF and disconnect power before changing
blades, adjusting tables/fence, or servicing.
10. Be aware of "kickback" hazards and how to prevent them.
11. Before starting, ensure tables are adjusted properly,
blades are secure, and jointer is stable.
12. Do not joint boards with cracks, loose knots, or defects.
5012917
13. Only operate in a dry environment free of rain/dampness.
14. Always support the workpiece against the fence and table.
Never attempt any operation free-handed.
Date
15. Always feed workpiece against cutterhead rotation. Never
move workpiece backward during operation.
SN
16. Prevent unauthorized use by children or untrained users;
Mfd. for Grizzly in Taiwan restrict access or disable machine when unattended.
Failure to keep hands clear of cutterhead
may result in serious personal injury.
REF PART # DESCRIPTION
116 P0725116 READ MANUAL LABEL
117 P0725117 CUTTERHEAD GUARD LABEL
118 P0725118 EYE/LUNG HAZARD LABEL
119 P0725119 ELECTRICITY LABEL
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
BUY PARTS ONLINE AT GRIZZLY.COM!
-40-
Scan QR code to visit our Parts Store.
Main Parts List (Cont.)
Labels & Cosmetics
Cutterhead
exposed
Failure to keep hands clear of cutterhead
between
may result in serious personal injury.
these lines
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
WARNING!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual, call
(800) 523-4777 or go to
www.grizzly.com.
Failure to keep hands clear of cutterhead
may result in serious personal injury.
122
Cutterhead
exposed
Failure to keep hands clear of cutterhead
between
118
may result in serious personal injury.
these lines
REF PART # DESCRIPTION
112 P0725112 FENDER WASHER 5MM
113 P0725113 INFEED TABLE SUPPORT ARM
115 P0725115 WIRE RESTRAINT
123 P0725123 T-HANDLE TORX DRIVER T-30
124 P0725124 FLAT WASHER 10MM
126 P0725126 EXT RETAINING RING 4MM
127 P0725127 FLAT WASHER 6MM
DANGER!
ROTATING
CUTTERHEAD
BELOW!
Use this guard for
all operations
possible, and
immediately
Cutterhead reinstall it following
exposed
operations that
Failure to keep hands clear of cutterhead
between
require its removal.
may result in serious personal injury.
these lines
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
REF PART # DESCRIPTION
120V3 P0725120V3 MACHINE ID LABEL V3.05.20
121 P0725121 CUTTERHEAD EXPOSURE LABEL
122 P0725122 TOUCH-UP PAINT GRIZZLY GREEN
Model G0725 (Mfd. Since 02/20)
Weight: 76 Lbs.
sleeves.
DANGER! WARNING! WARNING!
9. Turn motor OFF and disconnect power bef
ROTATING KICKBACK ALWAYS USE
blades, adjusting tables/fence, or servicing
CUTTERHEAD HAZARD PUSH BLOCKS!
BELOW!
10. Be aware of "kickback" hazards and how t
11. Before starting, ensure tables are adjusted
blades are secure, and jointer is stable.
1. Ensure outfeed
table is even with
Push blocks
Use this guard for
12. Do not joint boards with cracks, loose kno
knives.
all operations minimize the
2. Never exceed the
13. Only operate in a dry environment free of r
possible, and possibility of
maximum depth
immediately operator's hands
of cut.
14. Always support the workpiece against the
reinstall it following contacting the
3. Do not stand
operations that cutterhead while Never attempt any operation free-handed.
Date directly behind
require its removal. workpiece. cutting.
15. Always feed workpiece against cutterhead
move workpiece backward during operatio
SN
16. Prevent unauthorized use by children or un
restrict access or disable machine when u
Mfg. for Grizzly in China
WARNING! WARNING!
KICKBACK ALWAYS USE
HAZARD PUSH BLOCKS!
1. Ensure outfeed
table is even with
Push blocks
knives.
minimize the
2. Never exceed the
possibility of
maximum depth
operator's hands
of cut.
contacting the
3. Do not stand
cutterhead while
directly behind
workpiece. cutting.
EYE/LUNG INJURY
119
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
116
WARNING!
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE T
To reduce risk of death
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed w
or serious injury, read
artwork changes are required, contact us immediately at
manual BEFORE using
machine.
To get a new manual, call
(800) 523-4777 or go to
www.grizzly.com.
117