Precor 700 Series Assembly Manual
  1. Manuals
  2. Brands
  3. Precor Manuals
  4. Treadmill
  5. Experience Series 700 Line
  6. Assembly manual
Precor 700 Series Assembly Manual

Precor 700 Series Assembly Manual

Hide thumbs Also See for 700 Series:
Table of Contents

Advertisement

Quick Links

700/600 Line Treadmill
Assembly Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 700 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Precor 700 Series

Summary of Contents for Precor 700 Series

  • Page 1 700/600 Line Treadmill Assembly Guide...

  • Page 3: Treadmill Assembly Guide

    Treadmill Assembly Guide Follow the steps in the order listed in this assembly guide. For more product Dash assembly information, visit us at www.precor.com. Heart rate WARNING bar assembly At least two people are required to assemble the equipment. DO NOT Arm cover attempt assembly by yourself.

  • Page 4: Hardware Kit

    Hardware kit Required tools Component Description Quantity • #3 Phillips head screwdriver Washer • 5/16-inch hex wrench • 7/32-inch hex wrench (3/8-inch) • 1/4-inch hex wrench • Torque wrench with tension to at least 25 ft-lbs (33.90 Nm) with 5/16-inch and 7/32-inch drivers Self-tapping pan head screw...

  • Page 5: Begin Assembly

    Begin Assembly Position the right side upright support near the base frame and route the data cable inside of the base side cover and up through the right upright. WARNING IMPORTANT DO NOT attempt to connect electrical power until all assembly DO NOT pinch or crush the cable during assembly.
  • Page 6 To complete the dash assembly: Dash attachment Remove the two screws from the back of the dash cover. Remove the dash IMPORTANT cover and set it aside with the screws. Two people are required to assemble the dash. Route the data cable through the right tube of the dash assembly, up the back To attach the dash: frame, and out through the top hole.
  • Page 7 Fit the tread arm into the heart rate bar and against the dash assembly. Attach To attach the heart rate bar: it using two screws and two washers . Use a hex key to partially tighten the screws. Position the heart rate bar assembly against the dash frame and attach it using two screws and two washers .
  • Page 8 Table 1 To attach the filter to the drive power cable: Position Connector Disconnect the existing power cable from the drive unit, power filter, and ground terminal. Then completely remove it from the treadmill. Drive input connectors Brown lead with quick-connect terminal Blue lead with quick-connect terminal Green and yellow lead with quick-connect terminal AC input cable to the power cable...
  • Page 9 Install the accessory jack Fit the lower ends of any optional console cables into the notch in the upper edge of the panel. Replace the panel and fully tighten the corresponding screws. IMPORTANT The touchscreen console includes an accessory jack panel that you must install on WARNING the treadmill.
  • Page 10 Attach the treadmill hood Attach the top part of the safety key assembly using two screws Place the hood onto the treadmill. Using a #3 Phillips head screwdriver, attach it using four screws . Fully tighten the fasteners. Figure 18 Figure 20 To attach the safety key assembly: Fit the bottom part of the safety key assembly onto the bottom of the dash...
  • Page 11 Attach the bottom arm cover using four screws To attach the dash arm assembly: Insert two grommets into of the dash arms, just above each upright support. Figure 23 Repeat Steps 1 through 3 to attach the covers to the other arm. Figure 21 Attach the front arm cover using four screws Figure 22...

  • Page 12: Console Installation

    Console installation Level the treadmill To attach a console, refer to the installation instructions shipped with your console. IMPORTANT Once you have attached all the cables, follow the steps below to complete Adjust only one rear foot at a time. DO NOT extend the adjustable feet more than assembly of your treadmill.
  • Page 13 Notes Failure to align the belt may cause the belt to tear or fray, which is not covered by the Precor Limited Warranty. • The tracking adjustments should only be done in quarter turn increments. Press STOP to stop the belt.

  • Page 14: Safety Code

    IMPORTANT The default setting for this feature is ON. An administrator can turn off this feature in the System Settings; however, Precor recommends it remain ON. Auto Stop™ (Automatic Stop) is a feature designed to bring the treadmill to a gradual stop after two minutes, when it is not in use.
  • Page 16 700/600 Line TRM Assembly Guide | 305285-101 rev A, ENU © 2018 Precor Incorporated | May 2018...

This manual is also suitable for:

600 series

Table of Contents