Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
PRODUCT SAFETY & LEGAL DISCLAIMER
IMPORTANT READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO
•
MAY CAUSE PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY.
Review the product package and contents prior to beginning the installation. Take care when
•
opening the packaging and removing items. If a return is needed you will want to return the product in
its original packaging if possible.
This instruction guide is provided as a GENERAL installation guide, some vehicles vary dimensionally
•
and may require additional steps.
Test fit the product on the vehicle prior to any third party modifications and or finishing. The
•
manufacturer and/or distributors do not accept responsibility for third party charges, labor and or
third part replacement modifications. Some modifications may void the factory warranty.
•
Exercise due-diligence when installing this product. The manufacturer and distributors of this product
do not accept any responsibility for vehicle damage or personal injury resulting from the installation of
this product. Careless installation and operation can result in serious injury or equipment damage.
•
This product is for general off-road use. All liability for installation and use rests with the
owner/operator.
INSTALLER: Once installation is complete, please return this guide along with other documentation
•
included in this product back to the consumer for future reference. The manufacturer/distributors of
this product do not guarantee this particular version will be available at a later date.
REV.01
© 2016 Go Rhino Products. All rights reserved
www.gorhino.com
589 W. Apollo St., Brea, CA 92821
PART NO.
● 730500T
PRODUCT DESCRIPTION:
● XE SERIES 50" WINDSHIELD LIGHT FRAME
APPLICATION:
● JEEP WRANGLER JL & GLADIATOR JT
P: 888 427 4466
1
Advertisement
Related Manuals for Go Rhino XE Series
Summary of Contents for Go Rhino XE Series
- Page 1 INSTALLATION INSTRUCTIONS PART NO. ● 730500T PRODUCT DESCRIPTION: ● XE SERIES 50” WINDSHIELD LIGHT FRAME APPLICATION: ● JEEP WRANGLER JL & GLADIATOR JT PRODUCT SAFETY & LEGAL DISCLAIMER IMPORTANT READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO •...
-
Page 2: Maintenance And Care
Installation of some of these products may alter the factory sensor system performance. • Factory sensors may read shackles or hooks protruding from the fairlead and or tow hooks. • All sensor testing is completed by Go Rhino Products and or third party testing labs on modified • vehicles. •... -
Page 3: Installation Instructions
Spacer 701001T8CA ASH-E232 Rubber Bumper * Item Pre-Assembled Go Rhino recommends you, the installer, read this installation instruction manual from front to back before installing the product. You may also click here to view an installation video or visit http://www.gorhino.com/Installation-Videos. - Page 4 ITEM QTY. NUMBER DESCRIPTION ITEM QTY. NUMBER DESCRIPTION 730500T0BA Logo Plate (Passenger) 730500T0AA Light Frame Upright (Driver) 730500T0AA Light Frame Upright (Passenger) 730500T0BA Logo Plate (Driver) 730500T5BA Retainer Bracket * Item Pre-Assembled © 2016 Go Rhino Products. All rights reserved REV.01...
- Page 5 Using a 1/8” hex bit socket, remove the (3) button head screws securing the mesh logo plate from each light frame upright, (Fig 1). Set aside the mesh logo plates and screws for re-installation later. Fig 1 Driver Side REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 6 Step-2 Using a 1/8” hex bit socket, remove the (2) 10-32 x ¼” button head screws securing the retainer plate from each light frame upright, (Fig 2). Set aside the retainer plates and screws for re- installation later. Fig 2 Driver Side REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 7 Step-3 On the driver side of the vehicle, use a T-50 Torx bit socket and remove the (2) Torx screws securing the cowl, (Fig 3). Discard the Torx screws. Fig 3 Remove Torx Screws Driver Side REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 8 (2) M8 x 55mm button head hex drive screws, (2) M8 lock washers and (2) M8 flat washers, (Fig 4). Snug but do not tighten the screws. Repeat for the passenger side light frame upright. Fig 4 F-G-H Driver Side REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 9 Note: Different length attachment screws and the addition of spacers (supplied by the end user) may be required due to the dimensional and attachment variation between light bar brands. Driver Side REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 10 LED light bar to the light frame uprights. Next tighten the (2) M8 screws securing each light frame upright to the vehicle, (Fig 8). REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 11 Step-9 Align the (3) holes in each mesh logo plate with the threaded holes in each light frame upright and install (3) 10-32 X ¼” button head screws, (Fig 9). Tighten the screws. Driver Side REV.01 © 2016 Go Rhino Products. All rights reserved...
-
Page 12: Limited Warranty
This warranty covers the cost of the product only and does not include the cost of removal, installation, third party modifications or shipping of the product. In no event shall Go Rhino be liable to buyer or any third party for any damage or harm caused by the product or use thereof, regardless of whether such damages were foreseeable and whether or not Go Rhino has been advised of the possibility of such damages, not withstanding the failure of any agreed or other remedy of its essential purpose.
Need help?
Do you have a question about the XE Series and is the answer not in the manual?
Questions and answers