Related Manuals for Bloomfield 9600 Single Cup
Summary of Contents for Bloomfield 9600 Single Cup
- Page 1 OWNERS MANUAL COFFEE BREWERS MODELS: 9600 SINGLE CUP INCLUDES: Installation Operation Use & Care Servicing Instructions Model: 9600 Single Cup Brewer PRINTED IN CHINA 77195 Rev. (-) ECN12792 M687 0207 cps...
-
Page 2: Warranty Statement
It also does not apply if the serial nameplate has been removed or unauthorized service personnel perform service. The prices charged by Bloomfield Industries for its products are based upon the limitations in this warranty. obligation under this warranty is limited to the repair of defects without charge by a Bloomfield Industries Authorized Service Agency or one of its sub-agencies. -
Page 3: Table Of Contents
EXPLODED VIEW & PARTS LIST WIRING DIAGRAMS MODEL STYLE FEATURES SINGLE 9600 COFFEE DISPENSER BREWER This manual applies to the following Bloomfield Industries product: 9600, 9600CA SPECIFICATIONS VOLTS WATTS WATER 120 VAC 1500 APPLICABILITY Thank You for purchasing this Bloomfield Industries appliance. - Page 4 FEATURES AND OPERATING CONTROLS - AUTOMATIC BREWERS Fig. 1 Features & Operating Controls for Single Cup Brewers...
-
Page 5: Precautions And General Information
PRECAUTIONS AND GENERAL INFORMATION WARNING: ELECTRIC SHOCK HAZARD All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock. WARNING: INJURY HAZARD All installation procedures must be performed by qualified personnel with full knowledge of all... -
Page 6: Installation
INSTALLATION READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION IMPORTANT: To enable the installer to make a quality installation and to minimize installation time, the following suggestions and tests should be done before the actual unit installation is started: CAUTION: ELECTRICAL DAMAGE DO NOT plug in or energize this appliance until all Installation... -
Page 7: Plumber's Installation Instructions
NOTE: Water supply inlet line must meet certain minimum criteria to insure successful operation of the brewer. Bloomfield recommends 1/4" copper tubing for installation of less than 12 feet and 3/8" for more than 12 feet from a 1/2" water supply line. -
Page 8: Installation Instructions
INSTALLATION (continued) WARNING: SHOCK HAZARD Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide such a ground. Electrical shock will cause death or serious injury. IMPORTANT: Supply power must match nameplate for voltage and phase. -
Page 9: Operation
Fig. 4 Water Flow Diagram A. START-UP For initial start-up, or if the brewer has not been used for an extended period of time: ♦ Be sure the water supply is properly connected and the water supply valve is turned ♦... - Page 10 OPERATION (continued) B. PROGRAM BREW VOLUMES 1. Load a fresh pod in the pod holder and lock the pod in place. Place 2. Press and hold both BREW SELECT KEYS for 5 seconds until a 3. Program BREW 1 SELECT key Fig.
-
Page 11: Operation - Brewing Coffee
1. Unlock the pod holder by pulling the LOCKING LEVER fully forward. 2. Pull the BREW TRAY fully forward, then lower tray. NOTE: Normally, the brewer will automatically discard the last pod. If the brewer has not been used for some time, the used pod may need to be removed by hand. -
Page 12: Cleaning Instructions
CLEANING INSTRUCTIONS CAUTION: BURN HAZARD Brewing and serving temperatures of coffee and tea are extremely hot. Hot beverage will cause serious skin burns. CAUTION: SHOCK HAZARD DO NOT submerge or immerse brewer in water. DO NOT pour, spill or splash water onto, into or over any internal component. -
Page 13: Sanitizing Instructions
PROCEDURE: Sanitize Coffee Brewer PRECAUTIONS: None FREQUENCY: Weekly TOOLS: Pod Sanitizer Packet Empty Container 1. Unlock the pod holder by pulling the LOCKING LEVER fully forward. 2. Pull the BREW TRAY fully forward. 3. Center a fresh POD SANITIZER PACKET on the grid of the LOWER POD HOLDER. -
Page 14: Troubleshooting Suggestions
TROUBLESHOOTING SUGGESTIONS SYMPTOM Water won’t heat Coffee level too high or low Tea brew is too strong or weak No brew plus no flow from hot water faucet No brew (faucet flows OK) No flow from hot water faucet (brew OK) Pod not dried at end of brew Poor coffee quality POSSIBLE CAUSE... -
Page 15: Servicing Instructions
ACCESS PANELS TOP PANEL: Remove top panel to access hot water tank, thermostat, heating elements, brew pump and tubing, brew solenoid, hot water dispenser solenoid and piping, pod holders and brew tray, Top panel is held by screws around the edge. Remove pod drawer to access bottom of brew tray. -
Page 16: Temperature Adjustment
SERVICING INSTRUCTIONS (continued) CAUTION: SHOCK HAZARD These procedures involve exposed electrical circuits. These procedures are to be performed by qualified technical personnel only. NOTE: Optimum brewing temperature range is 195ºF to 205ºF (90ºC to 96ºC). IMPORTANT: A mechanical thermostat will maintain temperature within ±5ºF. - Page 17 REMOVE TANK LID ASSEMBLY Fig. 8 Tank Lid Configuration Disconnect brewer from electric power. Turn OFF water supply. Remove top panel. Pull vent tube, inlet elbow and water level probe out of tank lid. Remove hi-limit thermostat from bracket. Disassemble brew valve bracket and faucet valve bracket from tank lid.
-
Page 18: Replace Solenoid
SERVICING INSTRUCTIONS (continued) Fig. 9 Wrench #86660 Fig. 10 Clean Strainer Screen REPLACE SOLENOID Symptom: Brewer will not flow water; or, brewer drips continuously from pod holder or brew nozzle. NOTE: Wrench p/n 86660 is designed to allow easy removal of flare nuts from the water inlet fitting IMPORTANT: Shut-off water to brewer and disconnect brewer from electric power before removing hoses or wiring. - Page 19 CLEAN UPPER POD HOLDER Remove drip tray assembly and pod drawer. Slide brew tray fully forward. NOTE: Upper pod holder can be cleaned in place. It is not normally necessary to remove the pod holder from the carriage for cleaning. Remove retaining screw from spray disk.
- Page 20 SERVICING INSTRUCTIONS (continued) IMPORTANT: The two keypad ribbon cables connectors are not polarized and can easily be installed in the wrong position. Be sure to mark the ribbon cable connectors for orientation. REPLACE CONTROLLER Disconnect brewer from electric power. Remove top panel Note location of wire connections.
- Page 21 NOTE: Repeat steps 4 thru 5 as required to remove all scale and lime build-up. NOTE: Normally, silicone hoses do not need to be delimed. Should deliming hoses become necessary, Bloomfield recommends replacing the hoses.
-
Page 22: Exploded View & Parts List
EXPLODED VIEW & PARTS LIST CABINET COMPONENTS... - Page 23 ITEM PART NO. DESCRIPTION (page 22) BREW DRAWER ASSY 87136 UPPER HOUSING, LEFT 87175 UPPER HOUSING, CENTER 87137 UPPER HOUSING, RIGHT 86976 COVER, TOP 86975 LOWER HOUSING 86982 BASE ASSY 81732 LEG, LEVELING CORD & CAP, NEMA 5-15P 86618 STRAIN RELIEF 84382 SWITCH, ON/OFF 84427...
- Page 24 EXPLODED VIEW & PARTS LIST BREW TRAY COMPONENTS...
- Page 25 ITEM PART NO. DESCRIPTION 86946 DRAWER FRONT 86947 DRAWER PULL 89861 FRONT PLATE 86951 DRAWER ARM 85621 ELBOW FITTING 55487 SCREW 8-32x5/16 TR SS 86957 LOWER POD CARRIER ASSY 86847 PLATE RING UPPER 86949 SEAL RING 86956 SPRAY DISK LOWER 86844 ARM GUIDE 86972...
-
Page 26: Service Parts Kits
EXPLODED VIEW & PARTS LIST (continued) SERVICE PARTS KITS 84427 VALVE ASSEMBLY, COMPLETE 85218 INLET FITTING KIT ( Includes cap, fitting, gasket & strainer) 85219 INLET STRAINER... -
Page 27: Wiring Diagrams
WIRING DIAGRAM... - Page 28 Bloomfield Industries proudly supports CFESA Commercial Food Equipment Service Association Bloomfield Industries, Inc. Division of Carrier Commercial Refrigeration In US and Canada Telephone: 775-689-5700 Fax: 888-492-2783 Fax: 800-356-5142 ( for orders only website: www.wellsbloomfield.com PRINTED IN CHINA...
Need help?
Do you have a question about the 9600 Single Cup and is the answer not in the manual?
Questions and answers