The Anti-Tip Bracket; Important Safety Instructions - Whirlpool IKEA IEL730C Technical Education

Gas and electric slide-in ranges
Hide thumbs Also See for IKEA IEL730C:
Table of Contents

Advertisement

The Anti-Tip Bracket

The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without the
anti-tip bracket fastened down properly.
Anti-Tip
Bracket
Range Foot

IMPORTANT SAFETY INSTRUCTIONS

WARNING:
To reduce the risk of fire, electrical shock,
injury to persons, or damage when using the range, follow
basic precautions, including the following:
WARNING:
TO REDUCE THE RISK OF TIPPING OF
THE RANGE, THE RANGE MUST BE SECURED BY
PROPERLY INSTALLED ANTI-TIP DEVICES. TO CHECK
IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE
RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET
SECURELY ATTACHED TO FLOOR OR WALL, AND
SLIDE RANGE BACK SO REAR RANGE FOOT IS UNDER
ANTI-TIP BRACKET.
WARNING:
NEVER use this appliance as a space
heater to heat or warm the room. Doing so may result in
carbon monoxide poisoning and overheating of the oven.
WARNING:
NEVER cover any slots, holes or passages
in the oven bottom or cover an entire rack with materials
such as aluminum foil. Doing so blocks air flow through the
oven and may cause carbon monoxide poisoning.
Aluminum foil linings may also trap heat, causing a fire
hazard.
CAUTION:
Do not store items of interest to children in
cabinets above a range or on the backguard of a range –
children climbing on the range to reach items could be
seriously injured.
A child or adult can tip the range and be killed.
Verify the anti-tip bracket has been properly installed and engaged per installation instructions.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
To verify the anti-tip bracket is installed and engaged:
Slide range forward.
Look for the anti-tip bracket securely attached to floor or wall.
Slide range back so rear range foot is under anti-tip bracket.
See installation instructions for details.
SAVE THESE INSTRUCTIONS
WARNING
Tip Over Hazard
Proper Installation – The range, when installed, must be
electrically grounded in accordance with local codes or, in
the absence of local codes, with the National Electrical
Code, ANSI/NFPA 70 . In Canada, the range must be
electrically grounded in accordance with Canadian
Electrical Code. Be sure the range is properly installed and
grounded by a qualified technician.
This range is equipped with a three-prong grounding plug
for your protection against shock hazard and should be
plugged directly into a properly grounded receptacle. Do
not cut or remove the grounding prong from this plug.
Disconnect power before servicing.
Injuries may result from the misuse of appliance doors or
drawers such as stepping, leaning, or sitting on the doors
or drawers.
Maintenance – Keep range area clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.
Storage in or on the Range – Flammable materials should
not be stored in an oven or near surface units.
Top burner flame size should be adjusted so it does not
extend beyond the edge of the cooking utensil.
For self-cleaning ranges –
Before Self-Cleaning the Oven – Remove broiler pan and
other utensils. Wipe off all excessive spillage before
initiating the cleaning cycle.
Vesta Gas and Electric Slide-In Range
3
GENERAL INFORMATION
n
1-3

Hide quick links:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IKEA IEL730C and is the answer not in the manual?

Questions and answers

Akemi Kuroda
March 6, 2025

HOW TO REPLACE WIRING FOR THE OVEN CONTROL PANEL BOARD

1 comments:
Mr. Anderson
March 6, 2025

To replace the wiring for the Whirlpool oven control panel board (IKEA IEL730C), follow these steps:

1. Disconnect Power – Turn off the oven and unplug it to avoid electrical shock.
2. Remove the Control Panel – Follow the “Removing the Control Panel” section in the manual.
3. Access the Wiring – From the back of the control panel, locate the control board and its electrical connections.
4. Disconnect Wires – Carefully remove the wiring connections from the control board. Take a picture or note the wiring positions for reference.
5. Install the New Control Board – Position the replacement board correctly and reconnect the wires according to the original configuration.
6. Reassemble the Control Panel – Secure the control panel back in place.
7. Restore Power – Plug the oven back in and test the control panel to ensure proper operation.

Always replace all parts and panels before operating. Failure to do so can result in electrical shock or injury.

This answer is automatically generated

Subscribe to Our Youtube Channel

Table of Contents