MTS Systems Temposonics R Series Operation Manual page 40

Temposonics R-Series SSI
®
Operation Manual
Optional installation hardware
Ø 15.3
(Ø 0.6)
Ø 2.2
(Ø 0.09)
O-ring for fl ange M18×1.5-6g
Part no. 401 133
For: RH, RF, RD4, RT4
Application: Flange M18×1.5
Material: Fluoroelastomer
75 ± 5 durometer
Optional installation hardware
Ø 19.2
(Ø 0.76)
Ø 2.2
(Ø 0.09)
O-ring for fl ange M22×1.5-6g
Part no. 561 337
For: RH
Application: Flange M22×1.5
Material: FPM
Optional installation hardware
¾"-16 UNF-3A
(0.43)
Hex-jam nut ¾"
Part no. 500 015
For: RH, RD4
Application: ¾"-16 UNF thread
Material: Zinc plated with nylon insert
13/ Follow the manufacturer's mounting instructions
Controlling design dimensions are in millimeters and measurements in ( ) are in inches
Ø 16.4
(Ø 0.65)
Ø 2.2
(Ø 0.09)
O-ring for fl ange ¾"-16 UNF-3A
Part no. 560 315
For: RH, RF, RD4, RT4
Application: Flange ¾"-16 UNF
Material: Fluoroelastomer
75 ± 5 durometer
Mounting clamp
5.3
28
(0.21)
(1.1)
50
2
(1.97)
(0.08)
68
(2.68)
Mounting clamp width: 14.6 (0.57)
Mounting clamp
Part no. 400 802
For: RP
Material: Stainless steel (AISI 304)
11
60 (2.36)
16 (0.63)
Ø 3.2 (Ø 0.13)
M3 fastening screws (6×)
3.2 (0.13)
Fixing clip
Part no. 561 481
For: RH, RD4, RT4
Application: Used to secure sensor
rods (Ø 10 mm (Ø 0.39 in.) when
using an U-magnet
Material: Brass, non-magnetic
Ø 21.9
(Ø 0.86)
O-ring for pressure fi t fl ange
Part no. 560 705
For: RD4
Application: Pressure fi t fl ange
Material: Nitrile rubber
T-slot nut
9
M5 thread
(0.35)
4
(0.16)
9
(0.35)
8
4.5
(0.31)
(1.8)
T-slot nut
Part no. 401 602
For: RP
Fastening torque for M5 screw: 4.5 Nm
Cable connectors
13
54
(2.13)
M16 connector (7 pin) female, straight
Part no. 370 624
For: RP, RH, RD4, RT4, RF
Material: Zinc nickel plated
Termination: Solder
Contact insert: Silver plated
Cable Ø: 6...8 mm (0.24...0.31 in.)
Operating temperature:
−40...+100 °C (−40...+212 °F)
Cable clamp: PG9
Ingress protection: IP65, IP67
40
Ø 27
(Ø 1.06)
Ø 2.6
(Ø 0.1)
Back-up ring for pressure fi t fl ange
Part no. 560 629
For: RD4
Application: Pressure fi t fl ange
Material: Polymyte
90 durometer
Optional installation hardware
M18×1.5-6g
11.5
(0.45)
Hex-jam nut M18
Part no. 500 018
For: RH, RD4
Application: M18×1.5 thread
Material: Steel, 2 zinc, plated
(~2.13)
M16 connector (7 pin) female, angled
Part no. 560 779
For: RP, RH, RD4, RT4, RF
Material: Zinc nickel plated
Termination: Solder
Contact insert: Silver plated
Cable Ø: 6...8 mm (0.24...0.31 in.)
Operating temperature:
−40...+95 °C (−40...+203 °F)
Ingress protection: IP67
Manuals & Software available at:
www.mtssensors.com
1.4
(0.05)
8.7
(0.34)
~ 54
Ø 20.5
(Ø 0.81)