MTS Systems Temposonics III Programming Manual

T E M P O S O N I C S
R G C o n n e c t o r :
Pin No. Wire Color
1 Gray
2 Pink
3 Yellow
4 Green
5 Red or Brown + 24 Vdc, Customer Supplied
6 White
7 -
4
5
RG Connector
m
I M P O R T A N T - Read this before you begin programming!
All Temposonics III position sensors are factory calibrated and should not require cali-
bration. However, if your application requires that the zero and span settings output be
modified, use the appropriate procedure below.
Velocity output changes must be made at the factory; they are not field-programmable.
When programming Temposonics III sensors, make sure that the setpoints are within
the active stroke length of the sensor.
T o o l s N e e d e d :
Flathead Screwdriver - to remove screws that access pushbuttons.
Jeweler's Screwdriver or equivalent - for depressing pushbuttons.
24 Volt Power Supply - to power the sensor.
M S C o n n e c t o r :
Function Pin No. Wire Color
Output #1 (Displacement) * A
0 to 10 Vdc, 10 to 0 Vdc, B
4 to 20 mA, 0 to 20 mA, C
20 to 4 mA, or 20 to 0 mA D
Return for Pin 1
Output #2
(Displacement or Velocity) *
0 to 10 Vdc, 10 to 0 Vdc, E
4 to 20 mA, 0 to 20 mA, F
20 to 4 mA, or 20 to 0 mA G
Return for Pin 3
DC Ground
No Connection
H
J
K
3
2
7
1
6
(Mating Connector: P/N 370013; MS3116F-12-10S)
I I I
C A U T I O N :
Function
White DC Ground
- No Connection
Gray Return for Pin D
Pink Output #1 (Displacement) *
0 to 10 Vdc, 10 to 0 Vdc,
4 to 20 mA, 0 to 20 mA,
20 to 4 mA, or 20 to 0 mA
Red + 24 Vdc, Customer Supplied
- No Connection
Yellow Output #2
(Displacement or Velocity) *
0 to 10 Vdc, 10 to 0 Vdc,
4 to 20 mA, 20 to 4 mA,
0 to 20 mA, or 20 to 0 mA
Green Return for Pin G
- No Connection
- No Connection
A
H
B
G
C
K
J
F
E
D
MS Connector
PROGRAMMING
A N A L O G
R 0 C a b l e I n t e g r a l C a b l e :
Wire Color Function
Gray Output #1 (Displacement) *
0 to 10 Vdc, 10 to 0 Vdc,
4 to 20 mA, 0 to 20 mA,
20 to 4 mA, or 20 to 0 mA
Pink Displacement Output Return
for Gray Wire
Yellow Output #2
(Displacement or Velocity) *
0 to 10 Vdc, 10 to 0 Vdc,
4 to 20 mA, 20 to 4 mA,
0 to 20 mA, or 20 to 0 mA
Green Displacement Output Return
for Yellow Wire
Red or Brown + 24 Vdc, Customer Supplied
White DC Ground
Recommended Load Resistance:
For Vdc output: >5K ohm
For mA output: ≤400 ohm
* When using dual outputs, outputs #1 and
#2 must have the same output scale (i.e.,
voltage or current) and the same orienta-
tion (i.e., forward or reverse acting).
O U T P U T
550596 B