Table of Contents
Advertisement
Cascades™ Series
Owners &
Installation Manual
Freestanding Woodstove
French Manual Download:
www.regency-fire.com
Manuel en Français:
MODEL: F1150
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
0219WS027S
920-130a
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
12.10.19
Advertisement
Table of Contents
Related Manuals for Regency Fireplace Products Cascades Series
Summary of Contents for Regency Fireplace Products Cascades Series
- Page 1 Cascades™ Series Owners & Installation Manual Freestanding Woodstove French Manual Download: www.regency-fire.com Manuel en Français: MODEL: F1150 Tested by: Installer: Please complete the details on the back cover and leave this manual with the homeowner. Homeowner: Please keep these instructions for future reference. 0219WS027S 920-130a FPI FIREPLACE PRODUCTS INTERNATIONAL LTD.
- Page 2 Thank-you for purchasing a REGENCY FIREPLACE PRODUCT. The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you have any questions about your product that are not covered in this manual, please contact the REGENCY DEALER in your area. “This wood heater has a manufacturer set minimum low burn rate that must not be altered.
-
Page 3: Table Of Contents
table of contents Wood Door & Handle Assembly ........22 safety label copy Fan Installation ............23 Safety Label for F1150 ..........4 Stainless steel smoke deflector installation ....24 dimensions Brick Flue Baffle Removal / Installation .......25 Seasoned Firewood .............26 Unit Dimensions ............5 Outside Air Dimensions ..........5 operation installation... -
Page 4: Safety Label For F1150
safety decal This is a copy of the label that accompanies each NOTE: Regency units are constantly being im- Regency Freestanding Woodstove (F1150). We proved. Check the label on the unit and if there is have printed a copy of the contents here for your a difference, the label on the unit is the correct one. -
Page 5: Unit Dimensions
dimensions Unit Dimensions Unit with legs 20" 508mm " 441mm 24" " 610mm 165mm " 540mm Unit with pedestal 4-9/16" (115mm) Outside Air Dimensions Rear with pedestal with bottom heat shield + legs Front 4-15/16" (126mm) Rear 4-9/16" (115mm) Rear F1150 Regency Freestanding Woodstove Front... -
Page 6: Modular Installation Options
installation Too tall a chimney may prompt excessive On pedestal units there are two locations where 1. Please read this entire manual before you install draft which can result in very short burn outside air may be adapted to the unit. If using and use your new woodstove. -
Page 7: Stove Assembly Prior To Installation
installation Stove Assembly Prior to Airmate Assembly for F1150 Rear Heat Deflector Installation Assembly for F1150 1. The airmate sits on top of the stove with the slots The F1150 unit requires the pedestal (or heat The rear heat deflector is supplied with the stove in the sides fitting over the curved deflector on shield and legs) to be attached to the base. -
Page 8: Pedestal Assembly Installation
installation Pedestal Assembly Installation Bottom Heat Shield and Legs Installation 1. For easier assembly, tip the stove on its back (onto a soft surface to prevent scratching) and The instructions below apply to the painted cast remove the front cover. leg. -
Page 9: Minimum Clearance To Combustible Materials
installation Minimum Clearance to Combustible Materials Please read the section below carefully as clearances depend on whether single wall or double wall pipe is installed on the stove. Measurements "From Unit" are from the top plate of the stove to a side wall or to a corner, and from the rear heat shield to a back wall. Clearances may only be reduced by means approved by the regulatory authority. -
Page 10: Minimum Alcove Clearance And Clearance To Combustible Materials
installation Minimum Alcove Clearance and Clearance to Combustible Materials The Regency Freestanding models have been alcove approved and must be installed with a listed double wall connector to the ceiling level. Single wall pipe (C Vent) is not approved for alcoves. Note: Minimum alcove ceiling height - 83"... -
Page 11: Floor Protection (Corner Installation)
installation Floor Protection (Corner Installation) A combustible floor must be protected by non-combustible material (like tile, concrete board, or certified to UL-1618 or as defined by local codes) extending beneath the heater and a minimum of 8" (203mm) from each side and minimum 16" (406mm)** from the front face of the stove and minimum 6"... -
Page 12: Step By Step Chimney And Connector Installation
installation Step by Step This stove may be connected to a lined masonry chimney or a listed factory built chimney suitable for 8. To complete your chimney installation, install Chimney and use with solid fuels and conforming to ULC629 in the double wall connector pipe from the Connector Installation Canada or UL-103HT in the USA. -
Page 13: Masonry Chimney
installation Masonry Chimney Ensure that a masonry chimney meets the mini- mum standards of the National Fire Protection Association (NFPA) by having it inspected by a professional. Make sure there are no cracks, loose mortar or other signs of deterioration and blockage. -
Page 14: Combustible Wall Chimney Connector Pass-Throughs
installation Combustible Wall Chimney Connector Pass-throughs Minimum chimney clearance to brick Method A: 12" (304.8 mm) Clearance to Combustible Wall Member: and combustibles 2 in. (50.8mm) Using a minimum thickness 3.5" (89 mm) brick and a 5/8" (15.9 mm) minimum wall thickness clay liner, construct a wall pass-through. Minimum clearance The clay liner must conform to ASTM C315 (Standard Specification 12 in. -
Page 15: Mobile Home Installation
installation Mobile Home Installation In addition to standard installation instructions the For Canadian Installations: see Outside Air following requirements are mandatory for installation Kit - Part # 846-502. in a mobile home. There are further requirements when installing this unit into a mobile home in Canada Only. 1. -
Page 16: Mobile Home Kit - For Canada
installation F1500 Mobile Home Kit - For Canada Mobile Home Kit - for Canada Note: The optional ash drawer cannot be used when using the Mobile Home Kit. Note: The optional ashdrawer cannot be used when using the Mobile Home Kit. The Mobile Home kit contains: 5. -
Page 17: Installing Outside Air From Pedestal Base
installation F1500 Installing Outside Air Using Bottom Heat Installing Outside Air From Pedestal Base Shield/Legs If installing outside air from pedestal base, do not remove knock out from rear of pedestal. This must remain in place. Mobile Home Box Square Transition Box Mobile Home Box Blanking plate Collar... -
Page 18: Recommended Heights For Woodstove Flue
installation TABLE 1 Draft is the force which moves MINIMUM RECOMMENDED FLUE HEIGHTS IN FEET air from the appliance up (Measured from the top of the unit) through the chimney. The # OF ELBOWS amount of draft in your chim- ney depends on the length of ELEVATION (FT) the chimney, local geography,... -
Page 19: Optional Outside Air Kit
installation Optional Outside Air Kit The Outside Air Kit is an option for Freestanding Stoves. Outside air for combustion can be brought in either through the bottom of the pedestal or through the rear plate of the pedestal. For both bottom and rear outside air the Pedestal Cover Plate must be installed. Loosen the 4 screws on the rear of the pedestal and slide the cover plate over them. -
Page 20: Brick Installation
installation Brick Installation Firebrick is included to extend the life of your stove and radiate heat more evenly. Check to see that all firebricks are in their correct positions and have not become misaligned during shipping. Install all firebricks (if bricks were removed at install) per the diagram below and place in their correct positions. Do not use a grate. -
Page 21: Removing Wooden Handle
installation Removing Wooden Glass Installation Handle Your Regency stove is supplied with 5 mm Neoceram ceramic glass that will withstand the highest heat that your unit will produce. In the event that you break your glass by impact, purchase your replacement from an authorized 1. -
Page 22: Wood Door & Handle Assembly
installation WOOD STOVES & INSERTS Wood Door & Handle Assembly WOOD DOOR & HANDLE ASSEMBLY Place the door onto the hinges and then place the door handle through the opening on the door, as shown in In preparation of installing the door handle, the nuts, Diagram 2. -
Page 23: Fan Installation
installation F1500 Fan Installation Fan assembly for use only with the room heater marked to indicate such use. FAN INSTALLATION FAN OPERATION (120V FAN) The fan is controlled by a rheostat which allows control of the heat 1. Remove the two screws from the top of the fan housing. output. -
Page 24: Stainless Steel Smoke Deflector Installation
installation Stainless steel smoke deflector installation The stainless smoke deflector is located in the upper front area of the firebox. The deflector is held in place with 2 bolts Prior to the first fire, ensure deflector is seated properly and secured with 2 hand tightened bolts which are accessible from behind the smoke deflector. Smoke deflector Smoke deflector is installed through the door opening in location shown in Diagram... -
Page 25: Brick Flue Baffle Removal / Installation
installation Brick Flue Baffle 4. Install two smaller baffle pieces on either side. Removal / Installation Baffle side pieces The flue baffle system located in the upper area of the firebox is removable to make cleaning your chimney system easier. The brick baffle must be installed prior to your first fire. -
Page 26: Seasoned Firewood
operating instructions Seasoned Firewood Operating Air Operating Instructions Handle Whether you burn wood in a fireplace, stove or insert, The F1150 is supplied with an air operating handle. With your unit now correctly installed and safety good quality firewood is the key to convenience, ef- The handle is used to adjust the air control for the inspected by your local authority, you are now ready desired heat output. - Page 27 operating instructions First Fire 4. During the first few fires, keep the combustion 11. If you have been burning your stove on a low rate at a moderate level and avoid a large fire. draft, use caution when opening the door. After When your installation is completed and inspected Only after 5 or 6 such fires can you operate the opening the damper, open the door a crack, and...
-
Page 28: Fan Operation
operating instructions Safety Guidelines Fan Operation Ash Drawer Operating Guidelines and Warnings Automatic 1. Only clean ashes out of the stove when the To operate the fan - turn on the rheostat. unit has cooled down. Remove the plug by CAUTION: Do not use chemicals for lifting on the handle using the tool provided. - Page 29 maintenance WARNING: Do not operate without CAUTION: DO NOT BURN GARBAGE either the Ash Plug properly seated or OR FLAMMABLE LIQUIDS SUCH AS the Ash Dump Plates screwed in place, GASOLINE, NAPTHA, OR ENGINE excessive temperatures will result. OIL. SOME FUELS COULD GENER- ATE CARBON MONOXIDE AND ARE CAUTION: Do not operate with broken VERY DANGEROUS.
-
Page 30: Maintenance
maintenance Maintenance Creosote Door Gasket It is very important to carefully maintain your fire- When wood is burned slowly, it produces tar and If the door gasket requires replacement 7/8" diameter place stove, including burning seasoned wood and other organic vapours combine with moisture to material must be used. -
Page 31: Secondary Air Tube Removal / Installation
maintenance 3. Grasp secondary air tube firmly with vise grips, using a hammer tap vise Secondary Air Tube Removal / Installation grips from right to left until air tube is released from grip. Remove. 4. Remove top left and right metal retainers, followed by the fragile three piece 1. -
Page 32: Vertical Stainless Deflector Replacement
maintenance Vertical Stainless Deflector Replacement 7/16'' Nuts 7/16'' Bolts Slide right + down to remove. Reverse to replace. Vertical Deflector Remove 2 front air tubes 1. Remove 2 front secondary air tubes (page 31) / vermiculite baffles (page 25). 2. Loosen the two 7/16'' bolts + nuts to remove / replace vertical baffle. 3. - Page 33 maintenance Annual Maintenance Completely clean out entire unit Annually Inspect air tube and bricks Replace any damaged parts. Adjust door catch assembly If unable to obtain a tight seal on the door - replace door gasket seal. Readjust door catch after new gasket installed. Inspect condition and seal of: Glass Gasket Door Gasket...
-
Page 34: Main Assembly
parts list Main Assembly Part # Description 075-070 Left Side Heat Shield 075-071 Right Side Heat Shield 075-040 Side Baffle Cover (Each) 075-058F Draft Control Lever 075-052 Bracket Probe 815-557 Rear Air Deflector 075-955 Baffle Complete Set (Center + Sides) 033-953 3/4 OD x 19-1/4 Airtube 3 Per Unit (Each) 846-570... - Page 35 parts list Main Assembly F1150 Regency Freestanding Woodstove...
-
Page 36: Bottom Shield And Legs
parts list Bottom Shield and Legs part # description 075-911 Bottom heat Shield 850-126 Black Cast legs (Set Of 4) 850-128 Nickel Cast legs (Set Of 4) 075-914 Ashdrawer Bottom Heat Shield 942-110 Ashplug 820-249 Ashplug Tool 075-079 Blanking Plate 905-008 5/16"... -
Page 37: Complete Brick Kit
parts list 075-960 F1150S Complete Brick Kit Fire bricks Size 4-1/4" x 7" 4-1/2" x 7" 9" x 4-1/2" 9" x 2" 3-1/2" x 4-1/2" (AD) 4-1/4" x 8" 3-1/2" x 2-1/4" Ashdump brick F1150 Regency Freestanding Woodstove... - Page 38 notes F1150 Regency Freestanding Woodstove...
-
Page 39: Warranty Warranty
warranty Limited Lifetime Warranty FPI Fireplace Products International Ltd. (for Canadian customers) and Fireplace Products U.S., Inc. (for U.S. customers) (collectively referred to herein as “FPI”) extends this Limited Lifetime Warranty to the original purchaser of this appliance provided the product remains in the original place of installation. The items covered by this limited warranty and the period of such coverage is set forth in the table below. - Page 40 warranty All warranty claims must be submitted by the dealer servicing the claim, including a copy of the Bill of Sale (proof of purchase by you). All claims must be complete and provide full details as requested by FPI to receive consideration for evaluation. Incomplete claims may be rejected.
- Page 41 warranty Limitations of Liability: The original purchaser’s exclusive remedy under this warranty, and FPI’s sole obligation under this warranty, express or implied, in contract or in tort, shall be limited to replacement, repair, or refund, as outlined above. IN NO EVENT WILL FPI BE LIABLE UNDER THIS WARRANTY FOR ANY INCIDENTAL OR CONSEQUENTIAL COMMERCIAL DAMAGES OR DAMAGES TO PROPERTY.
- Page 42 warranty Product Registration and Customer Support: Thank you for choosing a Regency Fireplace. Regency strives to be a world leader in the design, manufacture, and marketing of hearth products. To provide the best support for your product, we request that you complete a product registration form found on our Web Site under Customer Care within ninety (90) days of purchase.
- Page 43 notes F1150 Regency Freestanding Woodstove...
- Page 44 notes F1150 Regency Freestanding Woodstove...
- Page 45 notes F1150 Regency Freestanding Woodstove...
- Page 46 notes F1150 Regency Freestanding Woodstove...
- Page 47 F1150 Regency Freestanding Woodstove...
- Page 48 nstaller: Please complete the following information Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial No.: __________________________________________________________ Printed in Canada Regency is a trademark of FPI Fireplace Products International Ltd. © Copyright 2019, FPI Fireplace Products International Ltd. All rights reserved.