Midea i5 Extra Instruction Manual page 12

13mm
异常处理
15mm
本品在使用时如发现异常，请先查阅下表。
异常情况 可能原因
充电时未打开电源开关
主机无法充电
主机与充电端子未充分接触
主机无法返回充电 充电座摆放位置不对
主机被地面上电线，下垂的窗帘
布或毛毯须边缠绕
主机被困
边刷、滚刷等卡住，导致机器不
能正常行驶
未清扫完毕，返回充电 主机感知电量不足
电源开关未开
未按预约时间清扫
定时预约已取消
抹布支架磁铁脱落
抹布支架安装后，
水箱无水
主机不渗水
主机底座出水孔堵塞
地面打滑
主机出现漏扫，清扫
地面摆放的电线，鞋等物体影响
无规划，app端地图
机器正常工作
显示不规则
清扫中途被干扰
电源开关未打开
电量过低
主机不工作
左右轮跌落，三组跌落传感
器处于跌落状态
前方有障碍物
主机后退
撞板卡滞
其他无法处理的故障，请联系当地售后服务网点或拨打全国服务热线 : 400 8899 315
15mm
22
13mm
处理方法
打开电源开关
确保主机与充电端子充分接触
参照"主要操作"中充电前准备
主机会自主启动脱困模式，若未脱
困，需手动帮助
清洁边刷上的缠绕物，重启是否正
常运行，否则联系售后部门
对主机进行充电
打开主机电源开关
重新设置预约
联系售后
加水
清理出水孔和水箱滤网
如地板打蜡，风干后再使用
尽可能减少地面零散物品摆放
机器工作中，不要人为搬动或阻挡
打开电源开关
给机器充电
将机器平整紧贴地面放置
联系售后
清楚前方障碍物
轻拍撞板，检查是否有异物卡住
TROUBLE SHOOTING
In case of mis-function, please refer to the following table.
Problem Possible reason
- The power switch is not turned on
The appliance cannot while charging
be charged
- The appliance and charging terminals
are not in full contact
The appliance is unable - Docking stand is not positioned
to recharge correctly
- The appliance is covered by wires
on the ground, drooping curtain
fabric or blankets are twinded
The appliance get stuck
- Side brush and brushroll, etc.
get stuck, and the appliance cannnot
run normally
Not cleaned completely, - The appliance does not sense
and recharge it
enough battery power
No cleaning according - The power switch is not on
to the preset time
- Scheduled appointment is cancelled
- The mop holder magnet falls o
After the mop holder is
- There's no water in water tank
installed, the appliance
- The appliance base outlet hole
is impermeable
is blocked
- The ground is slippery
The appliance has missed
- Wires, shoes and other objects
sweeps, there is no plan
placed on the ground, a ecting the
for cleaning, and the map
normal operation of the appliance
in app shows irregularly
- Cleaning is interrupted halfway
- The power switch is not turned on
- Low battery
- wheels are dropped and the three
Appliance does not work
groups of drop sensors are in a
falling state
- There's obstacle ahead
Appliance retreats
- Bumaper rail is clamped
If the problem still can't be solved, please contact local service center or call the hotline: 400 8899 315
13mm
15mm
Solution
- Power on the appliance
- Make sure the appliance is fully in contact
with the charging terminal
- Be ready to charge before using
''Main Operations''
- The appliance will automatically start the
escape mode. If it is not out of trouble,
it needs manual help.
- Clean the windings on the side brush and
restart it. If not, contact the after-sales
department.
- Charge the appliance
- Turn on the power switch of appliance
- Reset and make appointment
- Contact the aftersales service center
- Add water
- Clear water outlet and tank filter
- If the floor is waxed, dry it before use
- Minimize ground items as much as possible
- Do not move or block the appliance
during work
- Turn on the power switch
- Charge the appliance
- Place the appliance close to the ground
- Contact aftersales service center
- Clear the front obstacles
- Tap the bumper rail to check for if there's
foreign matter stuck
15mm
23
13mm