Pentair MAGICSTREAM LAMINAR Installation And User Manual page 11

Control Summary (Standard Mode)
Start programming with the LED light engine ON. Change programs and modes by cycling the power ON and O F F rapidly
(1 Sec). Wait 10 seconds between MODE changes.
PRO G RAM
/MODE
R E S E T O F F / O N/ O F F / O N/ O F F / O N/ O F F / O N
S O L E N O ID
T H U M P E R
L O C K C O L O R
L E D LIG H T
C O L O R
C H A N G E
Sync Mode - C olors will ch a ng e at a bout 10 s e c. interv als. In this m od e , multiple L a min ars will ch ang e colors tog eth er. If th e
sole noid thump er mod e is turn e d on, th e thump ers on multiple L a min ars will thump tog eth er.
Random Mode - C olors will ch a ng e at a bout 10 s e c. interv als but in a completely ra ndom s e qu e nc e . In this mod e , multiple
L a min ars will N O T cha ng e colors tog eth er. If th e sole noid thump er mode is turn e d on, th e thum p ers will thump at ra ndom interv als
a nd multiple L a min ars will N O T thum p tog eth er.
Party Mode - C olors will ch ang e ra ndomly a nd slowly at first, th e n sp e e d up, until th e s e qu e nc e e nds with quick fla sh e s a nd str o be s.
T h e n th e s e qu e nc e starts a g ain with slow ch a ng e s. In this mode , multiple La min ars will N O T ch a ng e colors tog eth er. If th e sole noid
thump er mod e is turn e d on, th e thump ers will thum p at ra ndom intervals a nd multiple la min ars will N O T thump tog eth er.
Solenoid Thumper
T h e sole noid thump er fe ature cre ate s a "wrinkle" in th e la min ar stre a m, which cre ate s a brillia nt spot of light in th e la min ar arc.
C ycle th e pow er O F F /O N 3 tim e s to turn th e sole noid thump er O N a nd O F F.
In S ync Mod e it thumps e v ery 2 s e conds. In R a ndom a nd P arty mod e it thumps ra ndomly e v ery 1 to 3.5 s e conds.
Reset
W h e n you s ele ct th e re s et fe ature , th e L E D light e ngin e re v erts to th e R a ndom color ch a nging mod e with the solenoid thumper ON.
Cycle the power OFF/ON 4 times to reset the LED light engine. The lights will flash 5 times, and then turn on in Random Mode with
the thumper on.
NOTE: In the event of a power interruption or power loss and the units become out of sequence, turn the light switch on and then
off four times (Off/On, Off/On, Off/On, Off/On). The unit will flash five (5) times then reset all of the lights and start them in Random
Mode with the thumper on.
POWER CYCLE
O F F / O N/ O F F / O N/ O F F / O N
O F F / O N
O F F / O N/ O F F / O N
C OLOR CHANG E MODE DESCRIPTION
DESCRIPTION
R e s ets Light E ngin e to
R a ndom mod e a nd turns on
th e thum p er.
T urns sole noid "thump er" O N
or O F F
Locks on a ny s ele cte d color.
R eturns to pre vious color
ch ang e mod e .
S witch e s from on e color
ch ang e mod e to n e xt. After a
R e s et, R a ndom mod e is
running .
MAGICSTREAM
INDIC ATION
F la sh e s Light 5 tim e s
F la sh e s Light 4 tim e s
C olor is fix ed
S ync Mod e –1 fla sh
R a ndom Mod e –2 fla sh e s
P arty Mod e –3 fla sh e s
® Laminar Installation and User's Guide
9