Advertisement
DTP2 CrossPoint 82 • Setup Guide (Continued)
Command
Video Mute
Mute output video
Mute video on all outputs
Mute video and sync
Unmute video and sync
View output mute status
Audio Configuration
Set audio input format
View audio input format
Front Panel Lockout (Executive Modes)
Enable lock mode 1
Enable lock mode 2
Enable lock mode 3
Enable lock mode 4
Disable executive modes
IP Settings
Set switcher IP address
Set switcher DHCP mode
Set subnet mask
Set gateway IP address
Reboot network
NOTE:
IP settings do not take effect until the
Twisted Pair Protocol
Set input TP type
View input TP type
Set output TP type
View output TP type
DTP Remote Power Parameters
Set input remote power
View input remote power
Set output 2 remote power
View output 2 remote power
KEY:
X!
= Input selection
X@
= Output selection
X1)
= Enable or disable
X4@
= Video mute status
X5*
= Audio input type
X6^
= DTP remote power
X6&
= TP format
X8&
= IP address
X8*
= Subnet mask
X8(
= Gateway address
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide
© 2020 Extron Electronics — All rights re
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
6
ASCII Command
Response
VmtX@*1]
X@*1B
1B
Vmt1]
2B
Vmt2]
0B
Vmt0]
B
VmtX4@
}
AfmtIX!*X5*
E
I
X!*X5*AFMT
E IX!AFMT
}
]
X5*
1X
Exe1]
2X
Exe2]
3X
Exe3]
4X
Exe4]
0X
Exe0]
Ipi • X8&]
E X8&CI}
E X( DH}
IdhX1)]
Ips • X8*]
E X8*CS}
Ipg • X8(]
E X8(CG}
E 2BOOT}
Boot2]
E
}
2BOOT
command is executed.
HdbtIX!*X6&]
EIX!*X6&HDBT}
EIX!HDBT}
X6&]
EO 2*X6&HDBT}
HdbtO 2*X6&]
E O 2 HDBT}
X6&]
RpwrIX!*X6^]
EIX!*X6^RPWR}
EIX!RPWR}
X6^]
EO 2*X6^RPWR}
RpwrO 2*X6^]
EOX@RPWR}
X6^]
Inputs 1 through 8. For the Twisted Pair Protocol commands,
1
2
= Output 1 (HDMI/DVI),
= Output 2 (DTP2/XTP/HDBT)
0
1
= Off or disabled,
= on or enabled
0
1
= Unmuted,
= muted
0
1
= None (input muted),
= Analog aux line (5-pole captive screw),
4
= LPCM-2Ch Auto (AUX) (default),
0
= Off (No remote power, default),
0
1
= DTP2 format (default),
= XTP,
Format nnn.nnn.nnn.nnn,
Format nnn.nnn.nnn.nnn,
Format nnn.nnn.nnn.nnn,
on the Extron website.
served.
www.extron.com
Additional Description
Mute the video on output
Mute the video on all outputs.
Mute the video and sync on all outputs.
Unmute the video on all outputs.
•X4@
•X4@
]
View mute status
1
2
3
]
Set the audio format of input
View the audio format of input
Lock all front panel controls.
Lock the front panel except for input selection, logo
configuration, and volume adjustment.
Lock the front panel except for input selection and logos.
Lock the front panel except for volume adjustment.
Allow all front panel adjustments and selections.
Specify a new switcher IP address.
Enable or disable DHCP (
Specify a new subnet mask.
Specify a new gateway IP address.
Restart network connection after IP or DHCP changes.
Set the DTP2/XTP type for input
View the current DTP2/XTP type for input
Set the TP type for input
View the DTP2/XTP/HDBT setting
Set remote power on input
View remote power setting on input
Set remote power on output 2 to
View remote power setting on output .
5
= Multi-Ch Auto (AUX)
1
2
= DTP 12 VDC,
= DTP 48 VDC
2
= HDBaseT format (supported on output only)
192.168.254.254
= default
255.255.255.0
= default
0.0.0.0
= default
All trademarks mentioned are the property of their respective owners.
X@
.
1
2
X4@
for outputs
,
, and loop (
X!
X5*
to
.
X!
.
0
= default).
X!
X6&
to
.
X!
.
X!
X6&
to
.
X6&
on output 2.
X!
X6^
to
.
X!
.
X6^
.
X!
= Inputs 7 and 8 only.
2
3
= LPCM-2Ch,
= Multi-Ch,
3
).
68-3438-50 Rev. A
01 20
Advertisement
