Banner SureCross DX80N9X1S2N1M1 Manual page 7

SureCross DX80 Node with Integrated Battery
Range
900 MHz: Up to 4.8 kilometers (3 miles)
2.4 GHz: Up to 3.2 kilometers (2 miles)
Transmit Power
900 MHz: 21 dBm conducted
2.4 GHz: 18 dBm conducted, less than or equal to 20
dBm EIRP
900 MHz Compliance (150 mW Radios)
FCC ID TGUDX80 - This device complies with FCC
Part 15, Subpart C, 15.247
IC: 7044A-DX8009
2.4 GHz Compliance
FCC ID UE300DX80-2400 - This device complies with
FCC Part 15, Subpart C, 15.247
ETSI/EN: In accordance with EN 300 328: V1.7.1
(2006-05)
IC: 7044A-DX8024
Spread Spectrum Technology
FHSS (Frequency Hopping Spread Spectrum)
Link Timeout
Gateway: Configurable
Node: Defined by Gateway
Discrete Inputs
Rating: 3 mA max current at 30V dc
Sample/Report Rates: DIP switch configurable (see ta-
bles)
Discrete Input ON Condition
PNP: Greater than 8V
NPN: Less than 0.7V
Discrete Input OFF Condition
PNP: Less than 5V
NPN: Greater than 2V or open
Analog Input
Rating for 0 to 20 mA models: 24 mA
Rating for 0 to 10V models: 10V
Impedance: 100 Ohms
Sample/Report Rates: DIP switch configurable (see ta-
bles)
Accuracy: 0.1% of full scale +0.01% per °C
Resolution: 12-bit
Rating
IEC IP67; NEMA 6; (See UL section below for any ap-
plicable UL specifications)
P/N 147502 Rev. E
Radio and General
Power
Requirements: 3.6V dc low power option from an inter-
nal battery
Consumption: Less than 1.4 W (60 mA) at 24V dc
Housing
Polycarbonate housing and rotary dial cover; polyester
labels; EDPM rubber cover gasket; nitrile rubber, non-
sulphur cured button covers
Weight: 0.30 kg (0.65 lbs)
Mounting: #10 or M5 (SS M5 hardware included)
Max. Tightening Torque: 0.56 N·m (5 lbf·in)
Antenna Connection
Ext. Reverse Polarity SMA, 50 Ohms
Max Tightening Torque: 0.45 N·m (4 lbf·in)
Interface
Indicators: Two bi-color LEDs
Buttons: Two
Display: Six character LCD
Wiring Access
One 1/2-inch NPT
For European applications, power the DX80 from a Limited Power
Source as defined in EN 60950-1.
Inputs and Outputs
Discrete Output Rating (NMOS)
Less than 10 mA max current at 30V dc
ON-State Saturation: Less than 0.7V at 20 mA
Discrete Output
Update Rate: 1 second
ON Condition: Less than 0.7V
OFF Condition: Open
Output State Following Timeout
De-energized (OFF)
Switch Power Outputs
Analog configuration: one
Discrete configuration: one
To verify the analog input's impedance, use an Ohm meter to
measure the resistance between the analog input terminal (AIx)
and the ground (GND) terminal.
Environmental and Certifications
Shock and Vibration
IEC 68-2-6 and IEC 68-2-7
Shock: 30g, 11 millisecond half sine wave, 18 shocks
Vibration: 0.5 mm p-p, 10 to 60 Hz
www.bannerengineering.com - tel: 763-544-3164 7