SCAN DSA 10 Assembly And Instructions For Use
  1. Manuals
  2. Brands
  3. SCAN Manuals
  4. Stove
  5. DSA 10
  6. Assembly and instructions for use

SCAN DSA 10 Assembly And Instructions For Use

Wood-burning stove
Hide thumbs
Table of Contents

Advertisement

Quick Links

A S S E M B LY- A N D I N S T R U C T I O N S F O R U S E
Scan DSA 10
Congratulations on your new Scan wood-burning stove
You have purchased a product by one of Europe's leading manufacturer's of wood-burning stoves, and we are sure that you will have years of plea-
sure with your purchase. To make the best possible use of your stove, it is important that you follow our advice and instructions.
Please read this Assembly- and instructions manual before you start to assemble your stove.
S C A N A / S - 5 4 9 2 V I S S E N B J E R G

Advertisement

Table of Contents
loading

Related Manuals for SCAN DSA 10

Summary of Contents for SCAN DSA 10

  • Page 1 A S S E M B LY- A N D I N S T R U C T I O N S F O R U S E Scan DSA 10 Congratulations on your new Scan wood-burning stove You have purchased a product by one of Europe’s leading manufacturer’s of wood-burning stoves, and we are sure that you will have years of plea- sure with your purchase.

  • Page 2: Table Of Contents

    C O N T E N T S Table of contents Installation ...................... 3 Installation Approval Technical data and dimensions Dimension sketch Assembly ......................5 Unpacking Service package Type plate Product registration number Door Accessories Load bearing underlay Floor plate Adjusting screws Stainless-steel shelf Positioning your wood-burning stove...

  • Page 3: Installation

    To ensure best-possible functionality and safety for your installa- Rated heat load: 8 kW tion, we advise you to call a professional fitter. Our Scan Dealer will Chimney temperature: 270°C be able to recommend a qualified fitter in your area. For information on Scan Dealers, please go to www.scan.dk.

  • Page 4: Dimension Sketch

    N S TA L L AT I O N Dimension sketch Scan DSA 10 * Centre rear outlet ** Height to the beginning of the flue pipe at top outlet *** Centre fresh air intake...

  • Page 5: Assembly

    • Glove • Fire starters for first lighting Type plate All Scan wood-burning stoves are fitted with a type plate, that specifies the approval standards and the distance to flammable materials. Scan DSA 10 Freestanding room heater fired by solid fuel...

  • Page 6: Product Registration Number

    Adjusting screw Make a note of your stove’s product registration number here so Your Scan wood-burning stove has 6 adjusting screws at the base that you have it available if you need to contact us. which you can use to level the stove.

  • Page 7: Positioning Your Wood-Burning Stove

    A S S E M B LY Positioning your wood-burning stove The wood-burning stove must be set up so that the stove itself, the flue pipe, and the chimney can all be cleaned. Position near to non-flammable walls When positioning near a non-flammable wall, we recommend you keep a minimum distance of 50 mm between the rear of the product and the wall for cleaning purposes.

  • Page 8: Connection Between Stove And Steel Chimney

    Connection between stove and steel chimney Connection with 90° elbow pipe (top outlet) Your Scan dealer, or local chimney sweep, can advise you on choosing If you intend to use a 90° elbow pipe to connect the wood-burning a make and type of steel chimney. This ensures that the chimney stove, the cleansing lid on the elbow pipe must be in the vertical sec- will match your wood-burning stove.

  • Page 9: Flue Pipe With Damper

    A S S E M B LY Flue pipe with damper The wood-burning stove is provided factory side with a damper which we recommend be fitted in the flue pipe, see page 9 "Using your stove in various weather conditions". Flue pipe with damper fitted Fitting the damper To fit the damper, holes are drilled in the flue pipe.

  • Page 10: Fresh Air Intake

    National and local building regulations must be followed with regard to the connection of fresh-air intake. Fitting the fresh-air connection piece The Scan DSA 10 can be connected using a fresh-air connection piece. Installation of the fresh-air connection piece is shown below. Connection piece...

  • Page 11: Instruction For Use

    I N S T R U C T I O N F O R U S E CB Technology (Clean Burning) Smoke deflector plates Your wood-burning stove is fitted with CB technology. To ensure The smoke deflector plates are located in the upper part of the com- optimum burning of the gases released by the burning process, air bustion chamber.

  • Page 12: Instructions For Heating

    We recommend the use of fire starters, or similar products, which setting the combustion airflow to full power. Running the stove at are available from your Scan dealer. Using fire starters helps to light too low a temperature and with too little combustion air can lead the wood quicker, and keeps the burning process clean.

  • Page 13: Handling Fuels

    I N S T R U C T I O N S F O R H E AT I N G If you use damp wood, most of the heat it produces will be used to Using your stove in various weather conditions evaporate the water.

  • Page 14: Maintenance

    Carefully lift and open the door. You can easily remove the sooty build up by cleaning with a dry cloth and glass cleaner. Your authorised Scan dealer stocks a special glass cleaner for this purpose.

  • Page 15: Troubleshooting

    Scan dealer with a warranty claim. • Is the chimney the right height for its surroundings? The warranty covers all parts which in the opinion of Scan A/S require • In case of rear outlet, check that the smoke gas pipe does...
  • Page 16 Udgave: Scan A/S - DK-5492 Vissenbjerg DK 90081500-1 07.07.2010...

Table of Contents