SAFETY PRECAUTIONS Install or modify the equipment without the power connected. The installation and handling of these equipments must be performed by authorised personnel. The entire installation must be at least 40 cm. away from any other installation. With power supply: w Do not use excessive force when tightening the connector screws.
SYSTEM OPERATION O To make a call, the visitor should press the push button corresponding to the apartment he/she wants to contact. Some acoustic tones will be heard confirming the call is in progress. At this moment the call is received in the dwelling.
Door panel description. Main module Push buttons module Sound module EL620/2Plus Push buttons electronic module EL610D , for 5 single push-buttons or 10 double push buttons. Short connection cable, It is supplied with EL610D module (16 cm length). For the connection of the push-buttons between the sound module and the push buttons module EL610D and between push-buttons modules EL610D.
DOOR PANEL INSTALLATION mbedding box positioning. 1850 1650 1450 The upper part of the door panel should be placed at 1,65m. height roughly. The hole dimensions will depend on the type of door panel. Door panel 90CS CEV90 Model CEA90C CEV90C 99 mm.
Align the tabs on the sound module in their respective housings of the module frame and later exercise a light pressure until correct placement. If there is push buttons module repeat the above process, locating under the sound module, as shown in the drawing. Frame Frame Sound module EL620/2Plus Push buttons electronic module EL610D...
DOOR PANEL INSTALLATION old the frame on the embedding box. Insert the hinge that it is supplied with the product in the embedding box, as shown in the drawing. To hold the frame on the embedding box, insert the hinge in the housings arranged for this purpose in the frame, as shown in the drawing.
DOOR PANEL INSTALLATION lug the push buttons with the connection cable RAP-610D. Use the connection cable RAP-610D, for the connection of the push buttons between the sound module and the push buttons module EL610D and between push buttons modules EL610D, when the distance between modules to connecting is greater due to the composition of the door panels.
DOOR PANEL INSTALLATION escription of the configuration dip switch of the sound module. The SW1 configuration dip-switch is located at the upper right side of the back of the module. For dip switch settings, use the tool that is supplied with the sound module.
DOOR PANEL INSTALLATION inal adjustments. If after starting the system it 's considered that the audio volume isn't correct, proceed with the necessary adjustments as shown in the drawing. IMPORTANT: Before closing the door panel(s), do a test call and check all self-testing leds (page 63) don't show any error.
DOOR PANEL INSTALLATION oor panel assembly. In assemblies of a single door panel, it is ready from factory to be mounted. If the door panel to installing is of more than one module it will be necessary make some adjustments to join a door panel with other one.
POWER SUPPLY INSTALLATION nstalling the FA-PLUS/C ver. 938072 power supply. Install or modify the equipment without the power connected. The installation and handling of these equipments must be performed by authorised personnel. Install the power supply in a dry and protected place without risk of drip or water projections. Avoid to place it near to heating sources, in dusty locations or smoky enviroments.
TELEPHONE DESCRIPTION Coming from previous page erminal connection description and JP3 configuration jumper. T-7822VD: S+, S-: BUS E.of.Líne Connection to call repeater S-45. BUS: Digital communication bus. HZ : JP3 configuration jumper: Connection to door bell. PA, PB: Free-voltage connectors (see page 71). V2Plus system (video) BUS: Digital communication bus.
TELEPHONES PROGRAMMING rogramming the telephones. Set to ON the configuration dip switch number 2 (as shown in page 63). It is found at the rear of the sound module. The door panel emits a sound announcing that it has come into the programming mode.
EL620/2Plus To activate the lock release by means of an external push button, place this push button between 'CV1' and 'CV2' terminals of the door panel, regardless of the kind of lock release.
OPTIONAL CONNECTIONS uxiliary push button of T-7722VD and T-7822VD telephone. The auxiliary push button of the T-7722VD and T-7822VD telephones has two possible functions which are configurable by JP1 and JP2 jumpers: Activate the SAR-2PLUS unit to switch on the ligths, etc. See document TSAR-2Plus for its connection and configuration.
OPTIONAL CONNECTIONS pening the garage door. If the function of the auxiliary push button is shared by all the telephones, all the auxiliary push buttons must be connected in parallel, as shown in the following diagram: T-7722VD T-7722VD = Master. = Slave.
INSTALLATION DIAGRAMS Additional telephone T-7720 T-7720 T-7720 Next floor BUS HZ HZ BUS HZ HZ BUS HZ HZ T-7722VD T-7720 BUS HZ HZ BUS HZ PA PB Additional telephone T-7720 T-7822VD T-7822VD BUS HZ HZ BUS HZ PA PB BUS F .Linea BUS HZ PA PB BUS F .Linea 2Plus Nexa Door Panel...
Page 23
udio door entry system with d.c. lock release. The installation diagram shows the wiring of an audio door entry system with one or several door panels to enter into the building. If the system has one door panel only, do not take into account the connection towards others. If the system has more than one door panel, wire the second panel as shown on the diagram.
INSTALLATION DIAGRAMS Next floor T-7720 T-7722VD BUS HZ HZ BUS HZ PA PB T-7720 T-7722VD BUS HZ PA PB T-7720 T-7822VD BUS HZ PA PB BUS F .Ligne 2Plus Nexa Door Panel FA-PLUS/C TF-104 ver. 938072 230110 0 CV1 +12 Main Main IMPORTANT: Do not insert the resistor with a 2Plus system.
Page 25
udio door entry system with a.c. lock release and additional TF-104 transformer. The installation diagram shows the wiring of an audio door entry system with one or several door panels to enter into the building. If the system has one door panel only, do not take into account the connection towards others. If the system has more than one door panel, wire the second panel as shown on the diagram.
Remember this function is only active during the call and communication processes. Short-circuit 'CV1' and 'CV2' terminals of the EL620/2Plus sound module; then, there must be 12V (a.c. or d.c. depending on the kind of installed lock release) among the lock release terminals.
Golmar se reserva el derecho a cualquier modificación sin previo aviso. Golmar se réserve le droit de toute modification sans préavis. Golmar reserves the right to make any modifications without prior notice.