Related Manuals for golmar SV-372S Colour
Summary of Contents for golmar SV-372S Colour
- Page 1 T372ML rev.0113 Video door entry system Kits 2 wires installation SV-372S Colour Instructions manual Cod. 50121259...
-
Page 2: Table Of Contents
INTRODUCTION First of all we would like to thank and congratulate you for the purchase of this product. The commitment to reach the satisfaction of our customers is stated through the ISO-9001 certification and for the manufacturing of products like this one. Its advanced technology and exacting quality control will do that customers and users enjoy with the legion of features this system offers. -
Page 3: System Characteristics
SYSTEM CHARACTERISTICS Video door entry system with simplified installation (2 wire bus without polarity). Up to 2 access door panel. Up to 2 apartments (must be configured, see page 41 for the door panel and page 50 for the monitor). Up to 4 monitors per installation. -
Page 4: Description
DOOR PANEL DESCRIPTION oor panel description. Solo abrepuertas de corriente contínua only d.c lock release CV BUS Screws of fixation of the aluminium front (x2). Call push button for 1 or 2 apartments, (see page 41 and 51). Label push button. Wall attachment hook (x2). - Page 5 DOOR PANEL INSTALLATION oor panel positioning. 1850 1650 1450 The upper part of the door panel should be placed at 1,65m. The door panel has been designed to be placed under most of the environmental conditions However it´s recommended to take additional cautions, like the use of the supplied rainproof cover or the installation under a covered place.
- Page 6 DOOR PANEL INSTALLATION lace the door panel. Face the door panel to the wall by placing the top at 1,65m. height and insert the installation wires through the cables entry. Drill two holes of 6mm. diameter and insert the wallplugs. Fix the door panel with especified screws.
-
Page 7: Final Adjustements
DOOR PANEL INSTALLATION inal adjustments. If after starting the system it's considered that the audio volume isn't correct, proceed with the necessary adjustments as shown on the picture. ush button label. To customize the push button label, insert a flat screwdriver to accede to the label, remove the push button front cover, see picture A &... -
Page 8: Lock Release Installation
The FA-372 power supply uses 3 units over DIN guide. This device has been exclusively designed to be used on Golmar Kit video SV-372S Colour. Golmar will not be responsible of the possible damages caused for an improper use or when used for other purposes than the specified. -
Page 9: Monitor Description
MONITOR DESCRIPTION escription 372S monitor. Colour screen 7". function push buttons. Led indicator of function push button pressed. Microphone. Speaker. Switch End of Line. Attachment holes for bracket installation. Installation terminals: : Positive ( FA-372 power supply) : Negative( FA-372 power supply) BUS : Communication Bus ( without polarity) BUS : Communication Bus (... - Page 10 MONITOR DESCRIPTION unction push buttons. Push button to stablish / finish communication or intercom function (only available on systems with 2 or more monitors, for description and connection see page 48 & 51). In configuration menu mode : To scroll up through the menu or to increase the value of the selected option, (see page 49).
-
Page 11: Monitor Installation
MONITOR INSTALLATION emove the bracket installation. Unscrew the monitor bottom screws. Remove the bracket installation of the monitor. ix the bracket installation to the wall. Avoid to place the monitor near to heating sources, in dusty locations or smoky environments. The bracket can be fixed using an electrical emmbeding box or directly on the wall. - Page 12 MONITOR INSTALLATION onitor wiring. Connect the installation wires to the terminal connector, according to the installation diagrams. ix the monitor. Place the monitor align attaching holes of the monitor with the attachment hooks of the bracket installation. With help of an screwdriver, fix the monitor with especified screws, as shown on the picture.
-
Page 13: Intercom Function
MONITOR INSTALLATION ntercom function. 372S monitor, incorporate as standard the intercom function between two monitors of the same apartment in systems with two or more monitors. To enable this function it will be necessary that one monitor has been configurated as master and slave the rest of monitors, (see page 50). -
Page 14: Monitor Adjustments
MONITOR ADJUSTMENTS/PROGRAMMING onitor adjustments and programming. the configuration menu of the monitor allows changing the following options: -Selecting the option: Brightness, Contrast and Colour. Video -Selecting the option: To select melody, melody volume and voice volume. Audio -Selecting the option: To select house and to select room (Master/Slave). the following buttons on the front panel of the monitor allow to perform the next functions: Enter / exit the configuration menu mode. - Page 15 MONITOR ADJUSTMENTS/PROGRAMMING Coming from previous page To select a melody volume for call monitor, choose the " " option with help of the scroll buttons and select Audio this option by pressing the button ; the following SELECT MELODY VIDEO menu will be displayed.
-
Page 16: Installation Diagram
INSTALLATION DIAGRAM onnection to 1 apartment. Apartment 1 3rd Slave Monitor 2nd Slave Monitor 1st Slave Monitor Master Monitor 372S 372S 372S 372S FA-372 End of Line End of Line End of Line End of Line 230Vac Door panel 2 Door panel 1 PVS-222 PVS-222... -
Page 17: Sections Chart
INSTALLATION DIAGRAM ections chart. Distance up to Terminal 20m. 100m. BUS, BUS (Maximum distance system) 1,50mm² 1,50mm² BUS, BUS (Max. distance between monitors) 1,50mm² CV, CV 1,50mm² onnection of an a.c. lock release by using TF-104 transformer and SAR-12/24 relay. PVS-222 TF-104 SAR-12/24... -
Page 18: Troubleshooting Hints
TROUBLESHOOTING HINTS Nothing operates. Check the output power supply voltage between ' ' and '+' is of 17Vd.c. Otherwise, – disconnect the power supply from the installation and measure again. If its correct now, it means there is a short circuit in the installation. Disconnect the power supply from the mains and check the installation.