HySecurity SlideDriver 15 Programming And Operations Manual
  1. Manuals
  2. Brands
  3. HySecurity Manuals
  4. Gate Opener
  5. SlideDriver 15
  6. Programming and operations manual

HySecurity SlideDriver 15 Programming And Operations Manual

Vehicular slide gate operator with smart touch controller
Hide thumbs Also See for SlideDriver 15:
Table of Contents

Advertisement

Quick Links

Programming and Operations Manual
Programming and Operations Manual
SlideDriver
™
15, 30F, 40, 50VF2/3, 80, 200
Vehicular slide gate operator with Smart Touch Controller
SlideDriver
SlideDriver 50VF2/3

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SlideDriver 15 and is the answer not in the manual?

Questions and answers

Related Manuals for HySecurity SlideDriver 15

Summary of Contents for HySecurity SlideDriver 15

  • Page 1 Programming and Operations Manual Programming and Operations Manual SlideDriver ™ 15, 30F, 40, 50VF2/3, 80, 200 Vehicular slide gate operator with Smart Touch Controller SlideDriver SlideDriver 50VF2/3...
  • Page 3 SlideDriver 15, 30F, 40, 50VF 2/3, 80, 200 Programming & Operations Manual with HySecurity Smart Touch Controller MX3630-01 Revision J This document provides Important Safety Information, specifications, and references along with an overview of programming user and installer menu options, designing vehicle loop layouts,...

  • Page 4: Slidedriver 15, 30F

    SlideDriver 15, 30F, 40, 80, 200 SlideDriver 50VF Site Installation Overview Gate Face* Use shims as needed Grooved Drive Rail Screen Safety Mesh on Gate Height: Per UL 325 and ASTM F2200, all openings in a sliding gate up to a 72-inch (6 foot or 183 cm) height must be guarded or screened.

  • Page 5: Slidedriver (All Models) 50Vf Components

    Cover not shown Drive Arm, Motor Mount, Top Drive Arm, Motor Mount, Bottom Limit Hose Switches Release, Manual Motor, Hydraulic Combination AdvanceDrive and XtremeDrive Wheels (80 and 150 Models, only. Not available on 50VF series) www.hysecurity.com © 2019 Introduction MX3630-01 Rev. J...
  • Page 6 Vent plug Valve Coil, Quick Stop Valve, Quick Stop Valve, Braking Breather cap Valve, Check, Endhead Braking Kit Gauge, Pressure AWOG Valve, 2 Position Directional Valve Coil, Directional Quick Disconnect, Socket Reservoir MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 7: Table Of Contents

    Contents SlideDriver 15, 30F, 40, 80, 200 SlideDriver 50VF Site Installation Overview ........................iv SlideDriver (all models) 50VF Components ........................v SlideDriver (all models) 50VF Components ........................vi ...................1 elcome to ecurity Contact Information .................................2 Notices and Bulletins ...............................2 Supplemental Documents ..............................2 Important Safety Information .............................
  • Page 8 Check Time and Date ..............................56 User Menu ..................................56 Table 5: User Menu ................................57 Installer Menu ................................59 Table 6: Installer Menu ..............................59 Setting the Close Timer ..............................66 Test the Operator ................................67 viii MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 9 Photo Eye Connections: Smart Touch & Smart DC Controllers ..................98 Photo Eye Function ..............................98 Retro-Reflective Photo Eye Systems ........................99 Using Photo Eye Sensors instead of Vehicle Loops ......................99 Photo Eye Alignment Feature .............................101 www.hysecurity.com © 2019 Table of Contents MX3630-01 Rev. J...
  • Page 10 Drive Wheel Spring Tension (Adjustment of Manual Release) ..................125 Grooved Drive Rail ..............................126 Drive Wheel Assembly ..............................127 Hydraulic System Maintenance ............................128 Brake Valve Adjustments ............................129 Pressure Relief Valve Adjustments ..........................129 Open Valve ................................129 SlideDriver Operator Maintenance Schedule ......................130 MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 11 Smart Touch: Photo Eye / Reflective (E3K R10K4) .......................135 Smart Touch: The Solution, MIM-62 (Multi-input Module) ...................136 Smart Touch: iGAZE Kit Wiring Diagram ........................137 SlideDriver Installer Checklist ............................138 Appendix A - French Translations ..........................140 Specifications ................................145 www.hysecurity.com © 2019 Table of Contents MX3630-01 Rev. J...

  • Page 12: Welcome To Hysecurity

    Our commitment to quality and innovation will become evident as the features and performance of the expertly engineered and manufactured SlideDriver become familiar to you. Thank you again for the confidence you’ve shown in becoming part of the HySecurity family and in choosing a premium, industry-leading product. HySecurity Gate, Inc. Headquarters in Kent, WA www.hysecurity.com...

  • Page 13: Contact Information

    Contact Information Qualified HySecurity distributors are experienced and trained to assist in resolving any problems. For the name of a qualified distributor near you, call HySecurity at 800-321-9947. Before contacting your distributor or HySecurity Technical Support, obtain the serial number of your operator.

  • Page 14: Important Safety Information

    Obey all safety messages that follow HySecurity product manuals. ®...
  • Page 15  A minimum of three years experience installing ONE SHOULD CROSS THE similar equipment. PATH OF THE MOVING GATE.  Proof of attending a HySecurity Technical Start gate operator only when a gate’s travel path is clear. Training seminar within the past three years.
  • Page 16  Before attaching operator to gate, move gate  HySecurity gate operators have terminals for or barrier arm in both directions. Make sure it direct connection of up to three (3) external is level and travels freely.
  • Page 17 UL 325 gate usage class defi ned, and provides an alert that gate is about to move.Disabling warning buzzer may increase risk/extent of injury if entrapment occurs. SAVE THESE INSTRUCTIONS MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 18  NEVER use accessories or attachments that are activates non-contact sensors. After adjusting not recommended by HySecurity for this force or travel limit, retest gate operator. Failure equipment. Damage to the equipment and/or to adjust and test gate operator on a regularly injury to user may result.
  • Page 19  Never mix battery sizes, types, or brands.  NEVER grab or touch a live Charging circuit on HySecurity DC operators is power cord or cable with wet designed for AGM-type batteries, not lead acid- hands. The possibility exists of type batteries.
  • Page 20 SECONDARY ENTRAPMENT PROTECTION explode. If frozen, warm the battery to at least SENSORS 61°F (16°C). Most HySecurity gate operators are equipped with ENVIRONMENTAL SAFETY/HAZARDOUS a Type A, Inherent Entrapment Sensor (IES). UL 325 MATERIALS AND PROPER DISPOSAL Safety Standard compliance requires installation of...
  • Page 21 SENSOR SECURITY: A hard-wired contact gate travel and all hazard areas are fully protected. sensor shall be located and its wiring arranged HySecurity Gate operators require external so that communication between sensor and gate entrapment sensors that utilize Normally Closed is not subjected to mechanical damage.
  • Page 22 IMPORTANT SAFETY INFORMATION IDENTIFYING GATE OPERATOR CATEGORY AND USAGE CLASS Four different vehicular usage classes are defi ned in UL325. Most HySecurity operators are approved for use in all four UL325 defi ned usage classes. The four usage classes are described below:...
  • Page 23 1. Select Usage Class according to gate’s locale and purpose. 2. Required UL 325 inherent Type A sensor is an integral part of most HySecurity gate operators. 3. Based on gate’s usage class, choose External Entrapment Sensors: B1, B2, or D.
  • Page 24 Other AC power. “Compatible Sensors” may meet UL 325 7th Table 1. Sensors Tested for Use with HySecurity Operators Mfg. Part # Mfg. Details Hysecurity Part #...
  • Page 25 SENSOR 1,2, or 3 EMX WEL-200 Wireless Edge Receiver Dip Switch Settings determine which relay activates when the associated edge is tripped. Figure 2. WEL-200 or iGAZE RE SAVE THESE INSTRUCTIONS MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 26 (EDGE OPEN) Trailing End PUBLIC Photo eye Protecting Leading End (EYE CLOSE) SECURE Slide Gate Potential Leading End Entrapment Zones 1. Draw-in zone 2. Leading end 3. Trailing end SAVE THESE INSTRUCTIONS www.hysecurity.com © 2019 Important Safety Information MX3630-01 Rev. J...

  • Page 27: Important Safety Information

    IES. conditions may cause damage to gate operator and is not covered by the HySecurity Limited CAUTION Warranty. Do not adjust IES sensitivity to accommodate for inappropriately designed gate panels.

  • Page 28: Emergency Stop Button

    NOTE: For more information, refer to Drive Wheel Spring Tension (Adjustment of Manual Release) on page 125. Other types of release mechanisms exist. For example, the Fire and Emergency Access Lock Box is available through HySecurity distributors. Contact your distributor for more information. www.hysecurity.com ©...

  • Page 29: Power

    Code (NEC) - Article 250 requires a separate earth ground in addition to the required equipment ground. HySecurity recommends grounding the operator with a separate earth ground rod (or a similar device in the case of crash products) to shield the operator against electromagnetism and other electrical signals that may cause, erratic operation with, or damage to, the Smart Touch Controller and other electrical parts.

  • Page 30: Site Considerations

    Site Considerations HySecurity gate operators are intended for permanent installation. Make sure you prepare the site with the following considerations: • Make sure all electrical wiring is properly routed via conduits. • Check the distance of the wiring run from the main panel to the gate operator. Make sure the wire size of the branch circuit supplying power to the gate operator is large enough to avoid excess voltage drop.

  • Page 31: Turning The Power Switch On

    STATUS SENSOR 3 Turning the Power Switch ON DO NOT USE CHARGER AC LOSS HySecurity The AC power disconnect switch is located on the same enclosure LOCK INTERLOCK MX000585 VERSION (control box) where the electrical components, Smart Touch EMERG CLOSE Controller, transformer, power supply board, etc., are found.

  • Page 32: Wire Sizing And Runs

    7.0 miles (11 km) 20 ga 3.5 miles (5.6 km) 22 ga 2.7 miles (4.3 km) 24 ga 2.0 miles (3.2 km) 26 ga 1.0 mile (1.6 km) 28 ga 3700 feet (1.1 km) www.hysecurity.com © 2019 Power MX3630-01 Rev. J...

  • Page 33: Slidedriver Wiring Charts (Incoming Power)

    975 (297m) 515 (157m) 475 (145m) 260 (79m) 2220 (670m) 1915 (584m) 1550 (472m) 815 (248m) 750 (229m) 410 (125m) 3550 (1082m) 3080 (939m) 2465 (751m) 1305 (398m) 1200 (366m) 650 (198m) MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 34 5870 (1789m) 4650 (1417m) 2840 (866m) 2750 (838m) 1150 (350m) 11700 (3566m) 9350 (2850m) 7400 (2255m) 4550 (1387m) 4400 (1341m) 1800 (549m) 18500 (5639m) 14800 (4511m) 11700 (3566m) 7200 (2194m) 7000 (2134m) 2900 (884m) www.hysecurity.com © 2019 Power MX3630-01 Rev. J...

  • Page 35: Slidedriver 50Vf-Series Wiring Chart (Incoming Power)

    2530 (771m) 6990 (2130m) 8470 (2582m) Performance of 50VF-series Operators on 1 and 3 Phase, 50 or 60Hz A HySecurity 50VF-series operators can operate on a wide variety of incoming power. • 50Hz/60Hz operation with no changes or reconnection •...
  • Page 36 SlideDriver 50VF-series operators are NOT field reconfigurable between 208/230VAC and 460VAC power. The VFD Motor Controller in a 208/230VAC unit must be replaced with a VFD Motor Controller manufactured for the higher (460VAC) voltage input. www.hysecurity.com © 2019 Power MX3630-01 Rev. J...

  • Page 37: Control Transformer Connections (Non-Ups)

    You need a 2-inch (5 cm) diameter conduit for hydraulic hoses and a ¾-inch (19 mm) conduit for electrical wiring. AC input power is connected to the hydraulic pump and electrical components enclosure (HydraSupply). A supplemental manual, provided with the product, describes the installation overview, wiring and conduit considerations. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 38: Ups Backup Power Options

    110Ah DC batteries which, when AC power loss occurs, maintain a true Uninterrupted Power Supply (UPS) system. When the local AC power fails, the UPS back up system continues to move the gate. System features are covered in the HyInverterAC Installation and Reference Manual shipped with the product and available online at www.hysecurity.com. Straps Footman...

  • Page 39: Initial Setup

    All SlideDrivers ave the hoses configured at the factory for right handing. If the gate has left handing, the hydraulic hoses must be swapped. See page 29. OPEN OPEN Left-Hand Right-Hand Gate Gate MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 40: Hydraulic Hose Swap

    ¼-inch incremental turns on the adjustment stem with a hex key. Note that the adjustment screw varies depending on model type. 2. When the adjustment is complete, retighten the locking nut to hold the setting. www.hysecurity.com © 2019 Initial Setup...

  • Page 41: Grounding, Breather Cap Installation & Handing

    Gate Handing on page 28. Factory set for right-handing. Swap hose connections for left- handing gate. Grade level Cut-away view Consult local codes for proper depth Concrete foundation Ground rod MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 42: Slidedriver Standard And Slow Down Limit Ramps

    NOTE: For a 50VF-series SlideDriver, you will need to order four (4) Slow Down Limit Ramp Kits. CAUTION Be sure to securely fasten all limit ramps to the underside of SlideDriver 50VF the drive rail when installing a 50VF-series operator. Slow Down Limit Ramp Kit www.hysecurity.com © 2019 Initial Setup MX3630-01 Rev. J...

  • Page 43: Adjusting The Pressure Relief Valve

    5 hp 2000 psi CAUTION Never exceed the maximum psi setting. Hex head adjustment screw Hex socket adjustment screw SlideDriver 15, 40, 50VF The Pressure Relief SlideDriver 30F, 80, 200 Valve is located behind the motor on the pump rack or soft start manifold.

  • Page 44: Modbus Rtu In Slidedriver 50Vf-Series

    NOTE: An upgrade to the VFD began shipping in May 2017. It requires software version 4.55 or later. The VFD is a manufacturer’s replacement and it is not compatible with HySecurity VFD gate operators that were built prior to January 2012.

  • Page 45: Emergency Fast Operate (Efo) In Slidedriver 50Vf-Series

    NOTE: When you are in programming mode the buttons on the keypad change from Open, Close, and Stop to Previous, Next, and Select. Refer to Menu Mode Navigation on page 44. HYSECURITY GATE OPEN 1. Make sure the operator is turned ON and a Run mode status (example, GATE OPEN) appears on the Smart Touch Controller, which indicates the machine is operational.

  • Page 46: Installing A Push Button Device For Emergency Fast Operate (Efo)

    SENSOR 2 DO NOT USE STATUS SENSOR 3 Emergency Fast Close Speeds DO NOT USE CHARGER AC LOSS HySecurity Power Supply Board LOCK INTERLOCK MX000585 VERSION EMERG CLOSE Operator Close Speed EFO Close FIRE DEPT OPEN...

  • Page 47: Entrapment Protection

    HySecurity monitors all external entrapment sensors connections by looking for NC contacts connected to input terminals. Smart touch software cycles power to device and looks for a time delay from when device powers on to when the contact closes (sensor input pulled low, meaning the sensor is not blocked/tripped).
  • Page 48 An Edge Sensor can be either hardwired through an adapter module (Hy2NC) or a wireless transmitter receiver combo (WEL-200 or iGAZE RE). Figure below shows the wiring and dip switch settings of a WEL-200. For more information and wiring diagrams of other recommended sensors see the “HySecurity External Entrapment Sensor Wiring Guide”.

  • Page 49: Manufacturer's Responsibility

    While the gate is not operating will generate ERROR 2 (ERR2) - disconnected IES NOTE: A second open contact, in either direction of travel, will lock the gate operator and ENTRAPMENT MODE (ENTR) appears on the display. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 50: The Inherent Entrapment Sensor (Ies)

    The Inherent Entrapment Sensor (IES) The IES on HySecurity gate operators is an entrapment sensor that is required by UL 325 as a Type “A” detection sensor. It is tripped through software programming OR hydraulic pressure settings. It does not function solely on its own accord and must be connected to the Smart Touch Controller.

  • Page 51: How Software Handles Monitoring External Entrapment Protection Sensors

    SENSOR 3 S3 SENSOR 3 NOTE: NOTE: Three inputs for external entrapment protection sensors are available on the HySecurity gate operator controller. Table 3 indicates how the edge and photo eye inputs have been renamed to generic “sensor” inputs. They are interchangeable and configurable.
  • Page 52 NOTE: NOTE: When installing wired edge sensors, the wired edge must be connected to an interface module with an NC output. See Wiring HySecurity Sensors: Smart Touch on page 131. For wireless edge sensors, no interface module is required. Wireless edge sensors need the wireless gate links which include a transmitter and receiver.

  • Page 53: Table 4: Installer Menu Settings For Sensor Inputs

    ● ● ● ● ● ● ● SwingSmart DC ● ● ● ● ● ● ● HydraSwing ● ● ● HydraLift NOTE: NOTE: HySecurity does not update software for SlideWinder models. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 54: Supply Power To The Sensors

    All external entrapment protection sensors must be wired to the SENSOR COM terminal for monitoring purposes. Review sensor wiring diagrams found in Wiring HySecurity Sensors: Smart Touch on page 131. Until the gate operator receives a command to run (open or close command), the sensors are not receiving power (pre-h.4.56 and h.5.57 software).

  • Page 55: Control Panel Overview

    Provides inputs for peripherals and accessories, 2 electromechnical user relays (250VAC, 10A), one solid Power Switch state user relay (30VDC, 3A). For more information, refer to STC Terminal Inputs on page 71. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 56: Slidedriver Wiring Diagram, D0266 Rev B

    SENSOR 1 SENSOR COM DO NOT USE SENSOR 2 DO NOT USE STATUS SENSOR 3 DO NOT USE CHARGER AC LOSS HySecurity LOCK INTERLOCK MX000585 VERSION EMERG CLOSE FIRE DEPT OPEN Smart Touch Controller LIMIT DUAL GATE RADIO OPTIONS OPEN...

  • Page 57: Variable Speed Drive (Vfd) Control Box

    CAUTION Residual voltage remains in the VFD which can cause electrical shock to personnel or damage to the equipment.       MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 58: Variable Speed Drive Wiring Diagram, Pre-May 2017

    RED TO B5 DO NOT USE BLACK TO B7 SENSOR 2 DO NOT USE STATUS SENSOR 3 DO NOT USE CHARGER AC LOSS HySecurity LOCK INTERLOCK MX000585 VERSION EMERG CLOSE FIRE DEPT OPEN RS232 Smart Touch Controller SERIAL LIMIT DUAL GATE...

  • Page 59: Variable Speed Drive Wiring Diagram, May 2017

    Variable Speed Drive Wiring Diagram, May 2017 NOTE: VFD manufacturer’s upgrade released May 2017. Refer to Technical Bulletin located on the HySecurity website. New wiring diagram below. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 60: Stc Board, Power Supply Board And Display

    SENSOR 2 SENSOR 2 CLOSE DIRECTION OPEN DIRECTION OPEN DIRECTION DO NOT USE DO NOT USE DO NOT USE CHARGER AC LOSS HySecurity PHOTO EYE PHOTO EYE SENSOR 3 LOCK INTERLOCK MX000585 CLOSE DIRECTION VERSION EMERG CLOSE Updated silk FIRE DEPT OPEN...

  • Page 61: Display & Menu Options

    32 character display (OLED). RS-232 and RS-485 ports provide connections for external communication. A real time clock and an EEPROM logs events. HYSECURITY GATE STOPPED The STC display and keypad provide access to the operator’s sophisticated software and functionality.

  • Page 62: Initial Setup

    Initial Setup Once you have completed the installation of the HySecurity operator and attached the wired accessories, you’re ready to program the operator. Two different approaches exist: • Connect a laptop computer to the serial RS-232 connector and set the operator menu configurations via the S.T.A.R.T.

  • Page 63: Initial Setup Using S.t.a.r.t

    Initial Setup Using S.T.A.R.T. With the S.T.A.R.T. application (available online after registering at HySecurity) uploaded to your PC laptop, you can choose to set site menu configurations from the comfort of your office. Then, simply bring your PC laptop to the gate operator site, connect to the gate operator using an RS-232 to serial download cable and USB adapter, and download the configured menu settings file from your laptop to the specified gate operator.

  • Page 64: Menu Mode Navigation

    Press the Menu button Press Select. Continue pressing Next to view all Blinking characters Advance - press Next twice. Two left characters blink. selections. become static. Previous - press Previous www.hysecurity.com © 2019 Display & Menu Options MX3630-01 Rev. J...

  • Page 65: Run Mode And The Stc Keypad

    Pressing Reset clears alerts or faults and returns to Run Mode. 32-character display NOTE: Press Reset at identifies operator any Run mode status status. HYSECURITY HYSECURITY HYSECURITY GATE OPEN GATE CLOSED GATE STOPPED display to view the software version. For example: h4.53...

  • Page 66: Stop The Status Display Scrolling

    Change the Contrast on 7 Segment Displays NOTE: Since sunlight does not affect readability on the OLED display, changing the display contrast is not available on models shipped with the 32 character display. www.hysecurity.com © 2019 Display & Menu Options...

  • Page 67: Display Power Saving Mode

    The LED on the keypad appears blue to indicate Menu Mode. Use the navigational buttons, Select, Next, and Previous to change or view the menu functions. Refer to the chart, Smart Touch Controller: Menu Mode Navigation Buttons on page 53. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 68 The motor starts to secure the gate. If the gate does not fully close within 4s, the motor turns off and the buzzer sounds for 30 seconds. The display shows ALERT 1 - FORCED OPEN. www.hysecurity.com © 2019 Display & Menu Options MX3630-01 Rev. J...
  • Page 69 This parameter automatically resets to PC laptop loaded the default 0 (off ) after 24 hours, which is useful with HySecurity free when experiencing intermittent problems. Set to 0, S.T.A.R.T. software is DC Controller logs pertinent gate operator events required.

  • Page 70: Installer Menu

    NOTE: Installer Menu options can also be configured through the use of a laptop computer and S.T.A.R.T. software. See Smart Touch Analyze and Retrieve Tool information found on the HySecurity website: www.hysecurity.com Table 6: Installer Menu on page 59 describes the Installer Menu items and supplies the factory defaults.
  • Page 71 Select setting 1 to return operator to factory defaults. NOTE: If factory defaults are restored, the UL usage class, handing, gate weight, and any other modified menu settings will need to be reprogrammed. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 72 2 = default sensitivity entrapment sensor. Available settings 9 = lowest sensitivity are 1-9 with 9 being the least sensitive. HySecurity strongly recommends that you avoid setting IES sensitivity higher than 6. NOTE: Before changing IES sensitivity, make sure that gate rolls smoothly without obstruction.
  • Page 73 Same as Sensor 1 Same as Sensor 1 SENSOR 2 SENSOR #2 TYPE +24V SENSOR COM S3 0 Same as Sensor 1 Same as Sensor 1 SENSOR 3 SENSOR #3 TYPE +24V SENSOR COM MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 74 NOTE: The shaded Installer Menu items do not appear when Build Year is set to 2 (BY 2). Exceptions exist for barrier arms, CRASH products, operators set to pre-2016 and Usage Class IV provisions. www.hysecurity.com © 2019 Display & Menu Options...
  • Page 75 Maximum time setting is 135 seconds. 2 = 45 second delay NOTE: This menu controls a user relay set 3 = 75s to Function No. 8 4 = 105s 5 = 135s MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 76 If an HY-5B is used, additional settings of 4-8 SHADOW LOOP SET 1 = Show frequency (Reset Loop Set) 2 = Show call level 0-7 are available. 3 = Set Frequency www.hysecurity.com © 2019 Display & Menu Options MX3630-01 Rev. J...

  • Page 77: Setting The Close Timer

    DO NOT USE STATUS SENSOR 3 DO NOT USE 2. Use the Select, and then Next or Previous CHARGER AC LOSS HySecurity LOCK INTERLOCK MX000585 VERSION buttons to navigate and change the number EMERG CLOSE FIRE DEPT OPEN of seconds appearing on the display. Refer to...

  • Page 78: Test The Operator

    It will close a second or two faster than normal operation and ignore any photo eye, vehicle loop, or other safety sensor inputs. NOTE: If additional accessories are to be added, read about STC Inputs & Wiring on page 68. XtremeDrive (rack) shown www.hysecurity.com © 2019 Display & Menu Options MX3630-01 Rev. J...

  • Page 79: Stc Inputs & Wiring

    Make Connections on the Smart Touch Controller • Integrate with Security Systems • Adapt User Relays for your Gate Site LED lights when energized Hy5B Refer to the HySecurity website for more information about Hy5B installation and use. HY-5A Power Connector RS-485 RS485...

  • Page 80: Overview Of The Stc And Power Supply Board

    STATUS SENSOR 3 Two power supplies are available: DO NOT USE 24VDC and 24VAC CHARGER SHADOW AC LOSS HySecurity RESET A maximum draw of 3A is allowable when LOCK INTERLOCK MX000585 CENTER LOOP VERSION utilizing both power supply connections: EMERG CLOSE...

  • Page 81: Integrating With Security Systems And Hynet™ Gateway

    The RS-485 interface is also used to communicate with the HyNet Gateway, a web-enabled interface. To view the user guide and quick start information regarding HyNet Gateway SFP 4/1, go to the HySecurity website, Technical_Support_Installation_Manuals.

  • Page 82: Smart Touch Controller Inputs

    (TC 0) input. regulates the open timing. Free Exit Vehicle Free Exit N.O. input. Free Exit Vehicle Detector Vehicle detector, box type connections for Detector Vehicle connection. free exit loop. www.hysecurity.com © 2019 STC Inputs & Wiring MX3630-01 Rev. J...
  • Page 83 Power Protection Sensors on page 31 and Use these terminals to preserve battery - 24 Volts Wiring HySecurity Sensors: Smart Touch power. Common on page 111. NOTE: For pre-2016 gate operators, inputs are labeled as Photo Eye Power and 24 Volts Common.
  • Page 84 Fire Dept Jumper to +24. See the Table 6: Installer Enable Installer Menu FO & input +24V to Open Menu on page 50. trigger. Overrides photo eyes and gates edges. www.hysecurity.com © 2019 STC Inputs & Wiring MX3630-01 Rev. J...

  • Page 85: Connecting Accessory Devices

    Smart Touch Controller LIMIT DUAL GATE RADIO OPTIONS OPEN +24V +24V NOTE: See Wiring HySecurity Sensors: Smart Touch on page 131, for photo eye and gate edge connections. LOOP Not to Scale MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019...

  • Page 86: User Relays - Programming Procedure

    Activation timing of this relay is controlled by setting User Menu for Warn Before Operate [bF]. www.hysecurity.com © 2019 STC Inputs & Wiring MX3630-01 Rev. J...
  • Page 87 Recommended to use User Relay 3 since it is an electronic relay Free Exit Loop Vehicle Detector Active when the Free Exit Loop is tripped. Relay 1, 2 or 3 output MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 88: Hy8Relay Module Option

    AC power is present. Deactivated when AC power fails or gate is on open limit. Set aside for Factory Use HySecurity Testing Only Do not use Arm Break Does not appear. Displayed only used on StrongArm and StrongArmPark DC and activates if the breakaway arm switch is tripped.

  • Page 89: Bi-Parting & Dual Gate Systems

    NOTE: Both SlideDriver gate systems need to have compatible software versions installed on their Smart Touch Controllers. Bi-parting SlideDrivers MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 90: Dual Gate Wiring Connections

    DO NOT USE STATUS STATUS SENSOR 3 SENSOR 3 DO NOT USE DO NOT USE CHARGER CHARGER AC LOSS AC LOSS HySecurity HySecurity LOCK INTERLOCK LOCK INTERLOCK MX000585 MX000585 VERSION VERSION EMERG CLOSE EMERG CLOSE FIRE DEPT OPEN FIRE DEPT OPEN...

  • Page 91: Dual Or Sequenced Gates: Power, Software & Accessory Requirements

    RESET button on the operator. The software version appears beneath the word HYSECURITY. Keep the most current software loaded. It is available at www.hysecurity.com. Make it part of your maintenance routine to check for software upgrades on a regular basis.

  • Page 92: Connecting Sequenced Gates

    DO NOT USE STATUS STATUS SENSOR 3 SENSOR 3 DO NOT USE DO NOT USE CHARGER CHARGER AC LOSS AC LOSS HySecurity HySecurity LOCK INTERLOCK LOCK INTERLOCK MX000585 MX000585 VERSION VERSION EMERG CLOSE EMERG CLOSE FIRE DEPT OPEN FIRE DEPT OPEN...
  • Page 93 SG 4 = Sequenced Gate #4 configuration (only used with HydraSupply XL) NOTE : Set gate operators on the site to the uniquely paired number. Refer to the site designs on the following pages. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 94: Sequenced Gate: Configuration #1

    If a communication failure occurs, an ALERT 22 (AL 22) appears and the buzzer sounds. The Traffic Control Gate maintains functionality while the Security Gate defaults to Drawings not to scale. open until communication is restored (or the Security Gate is manually closed). www.hysecurity.com © 2019 Bi-Parting & Dual Gate Systems MX3630-01 Rev. J...

  • Page 95: Sequenced Gate: Configuration #2

    If a communication failure occurs, an ALERT 22 (AL 22) appears and the buzzer sounds. The Traffic Control Gate maintains functionality while the Security Gate defaults to Drawings not to scale. open until communication is restored (or the Security Gate is manually closed). MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 96 Page intentionally left blank www.hysecurity.com © 2019 Bi-Parting & Dual Gate Systems MX3630-01 Rev. J...

  • Page 97: Ehicle D Etector I Nstallation And L Oop L Ayouts

    Vehicle Detector Installation and Loop Layouts HySecurity recommends that vehicle detectors be used for free exit and obstruction sensing logic only. The exception is in parking or barrier arm applications where detectors may also be used to close the gate. In applications employing our swing, vertical lift, or sliding gate operators, closing logic cannot be used except when the anti-tailgate logic is employed.

  • Page 98: Vehicle Detectors And The Smart Touch Controller

    • compensation allows the Hy5B to operate with a higher sensitivity which provides better detection capability. No Loop Crosstalk – Exclusive use of Hy5B vehicle detectors in HySecurity gate operators, completely eliminates crosstalk and the • need to set frequency levels.

  • Page 99: Check The Version Of Software

    S.T.A.R.T. software to your PC laptop, and then load the gate operator code to the controller board before installing Hy5B vehicle detectors. See www.hysecurity.com for updates. NOTE: Hy5A emulation mode does not include all the features of Hy5B. If you are replacing Hy5A detectors and updating the gate operator software, be aware Build Year 1 (BY1) or Build Year 2 (BY2) will need to be addressed.
  • Page 100 Free Exit will not be detected. Conduit to gate operator For more information, refer to the Hy5B User Houses lead in wire Guide and additional instructional material found online HySecurity website / Tech Support. Underground Loop See Loop Layout: One Lane, Bi- or Single- Directional.

  • Page 101: Vehicle Detector And Loop Fault Diagnostics

    VEHICLE DETECTOR AND LOOP FAULT DIAGNOSTICS If HySecurity HY-5B vehicle detector modules are used, the Smart DC Controller has the ability to store and report detector and loop fault information for performance diagnostics. If the Smart DC Controller senses a loop or detector problem: •...
  • Page 102 Errors can be retrieved from the Smart DC Controller by downloading from the RS232 communications port or the USB port. HySecurity’s free START software, a laptop computer, and a special download cable or USB cable are required to retrieve and read this data.
  • Page 103 7 = Show Loop Health CLD 0 CENTER LOOP SET 3 = Set Frequency 8 = Set Presence (Can be used as an arming loop with User Relay 22.) 4 = Show Sensitivity MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series www.hysecurity.com...

  • Page 104: Installing Standard 11-Pin Box Type Vehicle Detectors

    Detector SENSOR 2 DO NOT USE To LOOP terminal on Smart STATUS Touch Controller SENSOR 3 DO NOT USE CHARGER AC LOSS HySecurity LOCK INTERLOCK MX000585 VERSION EMERG CLOSE FIRE DEPT OPEN Smart Touch Controller RADIO OPTIONS LIMIT DUAL GATE...

  • Page 105: Loop Layout: One Lane, Bi- Or Single-Directional

    (reversing loop). NOTE: A minimum of three (3) detectors are required for this type of gate site scenario. V-track gate shown; other gate types similiar. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series www.hysecurity.com...

  • Page 106: Photo Eye Installation

    NOTE: To enable fully automatic operation, this gate operator requires a MINIMUM of one external entrapment protection sensor to monitor potential entrapment zones in either the open or close direction of travel. Visit www.hysecurity.com/gatesafety for more information on UL 325 standards and gate safety.

  • Page 107: Photo Eyes (Non-Contact) Installation

    EXIT LOOP, IN OBS LOOP, and OUT OBS LOOP. Compatibility The UL 325 Standard of Safety requires that a photoelectric sensor be laboratory tested and “recognized” MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 108: Installation

    UL 325. In order to be compatible with all HySecurity gate operators, a photo eye must be rated to function from 24 VDC source power. A list of tested and approved external entrapment protection sensors (normally closed contacts) that are...

  • Page 109: Photo Eye Connections: Smart Touch & Smart Dc Controllers

    NOTE: Jumper between terminals on Photo Eye sensor so you don’t need to pull a fourth wire to the Controller terminal. For examples of wiring diagrams, refer to Wiring HySecurity Sensors: Smart Touch on page 131. To test Photo Eyes, see Supply Power to the Sensors on page 43.

  • Page 110: Retro-Reflective Photo Eye Systems

    UL 325 Standard of Safety for “monitored” external entrapment protection. To understand external entrapment protection CLOSE BUTTON REMOTE OPEN AND and how HySecurity equipment monitors sensors, refer to the section titled Entrapment Protection on page 36. RADIO CONTROL Smart Touch Controller...
  • Page 111 Placement of (7.3 m) photo eyes if used for vehicle Select appropriate distances SECURE SIDE detection between B, C, and D to make sure vehicles remain detected within the photo eye zones. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 112: Photo Eye Alignment Feature

    Press Next or Previous. Press the Menu button Press Select. Continue pressing Next to view all Blinking characters Advance - press Next twice. Two left characters blink. selections. become static. Previous - press Previous www.hysecurity.com © 2019 Photo Eye Installation MX3630-01 Rev. J...

  • Page 113: Installing Gate Edge Sensors

    (photo eyes) sensors in your site plan. Sensors are wired to the Controller and require low voltage conduit to the operator and power supply. For a list of tested and approved external entrapment protection sensors available for use with HySecurity gate operators, see the HySecurity website.

  • Page 114: Compatibility

    The UL 325 Standard of Safety requires that an edge sensor be laboratory tested and “recognized” under UL 325. In order to be compatible with all HySecurity gate operators, a edge sensor must be rated to function from 24 VDC source power.

  • Page 115: Gate Edge Function

    Hard-wired edge sensor adaptors (like Hy2NC) have inputs for up to two resistor terminated edges and up to two NC contact outputs. • HySecurity suggests the use of hard-wired edge sensor adaptors with an edge mounted to lead fence post to protect draw-in entrapment zone when the gate is running.

  • Page 116: Troubleshooting

    Alert buzzer emits distinctive chirping sounds. Any Alert, Fault, or Error is logged into memory and stamped with the date and time. These diagnostic messages can be retrieved for analysis purposes via optional S.T.A.R.T. software and a PC laptop. NOTE: S.T.A.R.T. configuration and diagnostic software is available at no charge from www.hysecurity.com. www.hysecurity.com © 2019 Troubleshooting MX3630-01 Rev.

  • Page 117: Typical Problems And Troubleshooting Procedures

    Eye Alignment Feature on page 101 and Eye Close Logic (EC) in Troubleshooting on page 105. If you have a battery-powered photo eye, check that the batteries are viable and the batteries are fresh. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 118: Table 8: Troubleshooting Codes

    Buzzer Chirp Sequence Suggested Corrective Solutions Action 1. Remove obstruction. ALERT HYSECURITY 2 chirps per second every 2s Occurs when IES is tripped when Entrapment Mode while control input is active gate is already in Safe Mode. 2. Adjust IES sensitivity.
  • Page 119 AC switch.Correct gate hardware. 3. Reset circuit breaker at electrical panel. 4. Have a licensed electrician check wiring. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 120 • Review wiring diagrams. Especially path to SENSOR • Make sure SENSOR settings S1, S2, and S3 are correctly assigned. Refer to External Entrapment Protection Sensors: What the Installer Needs to Do on page 40. www.hysecurity.com © 2019 Troubleshooting MX3630-01 Rev. J...
  • Page 121 On electromechanical gate operators and StrongArmCrash, reset the limits through the Installer Menu item, LL Learn Limits. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 122 HY-5B. This message will also indicate which detector alert applies to: Exit Loop (ELD), Inside Obstruction Loop (IOLD), Outside Obstruction Loop (OOLD), or Center Loop (CLD) - (User Relay 22). www.hysecurity.com © 2019 Troubleshooting MX3630-01 Rev. J...
  • Page 123 2 chirps per second every 15 An interlock contact is closed, EXT LOCK FAILED seconds indicating that the gate latch (lock) is engaged, preventing the operator from starting. Check the interlock terminal and wiring. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 124 VFD is experiencing a fatal error. If you cannot clear the error alert by pressing the open or close button, contact HySecurity. ALERT ALERT 22 2 chirps per second every 3 Appears when the RS-485 1.
  • Page 125 MOTOR RUN TIME 15 seconds is on longer than the maximum run time selected. Check and replace drive belt on applicable gate operators. Increase Max Run Timer in the Installer Menu. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 126 Check the wiring. Refer to the wiring diagram associated with the attached sensor. See Wiring HySecurity Sensors: Smart Touch on page 131. The 24V control voltage is FAULT FAULT 3...
  • Page 127 (or later). • If necessary, update the software using a PC laptop and S.T.A.R.T. Register and login in at www.hysecurity.com 1. Press RESET. ERROR ERROR 3 3 chirps per second once per Caused by HY-5B removal or...
  • Page 128 START. a serious internal error. Internal 3. Replace Smart Touch software/hardware error. Report any instance of this error to Controller. HySecurity Technical Support. ERROR ERROR 6 3 chirps per second once per Internal error between the STC STC-VFD minute board and the VFD.

  • Page 129: Access The Event Log Through The User Menu

    NOTE: Over 300 events can be recorded before the software begins overwriting the existing log history. The event log is also accessible through S.T.A.R.T. software with the use of a PC laptop and interface cable. Refer to the S.T.A.R.T. User Guide. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 130: Electrical Issues

    A general set of troubleshooting procedures are provided in the following paragraphs. Use a voltmeter to take the measurements described in the steps. If at any point in the process, a result different than what’s expected occurs, stop and identify the problem. Refer to Wiring HySecurity Sensors: Smart Touch on page 131. AC-Powered Gate Operators PROBLEM 1: Pushed the OPEN and CLOSE button, but the motor is not running.

  • Page 131: Mechanical Issues

    NOTE: If the gate speed must be changed, contact your HySecurity distributor or HySecurity Tech Support. Extremely cold weather is unlikely to seriously affect the gate speed because HySecurity employs a special grade of hydraulic fluid (Uniflow), which maintains a linear viscosity over a broad temperature range.

  • Page 132: General Maintenance

    With S.T.A.R.T. software loaded on your laptop computer, you have an invaluable management tool for all HySecurity operators. The RS-232 serial port (found on the Smart Touch Controller), allows you to download system diagnostics and upload system configurations using the S.T.A.R.T. software. The free S.T.A.R.T. software is conveniently located at www.hysecurity.com.

  • Page 133: Ssoftware Maintenance

    SSoftware Maintenance STC board software is constantly being enhanced with new features that create an easier install and improve on board diagnostic tools. Check the HySecurity website for atest version of software before heading out for field maintenance. Use S.T.A.R.T. software to download latest software version to a PC laptop and upload it to gate operator in the field.

  • Page 134: Mechnical Controls

    Mechnical Controls Stopping the Gate Most models (except SlideDriver 15 and 40) employ a time delay Soft Stop system. Additionally, brake valves are used to control the stopping of heavy or fast moving gates. These valves are exclusive to HySecurity operators. They are independently adjustable to allow the gate to stop predictably and without banging.

  • Page 135: Drive Rail

    (24 to 25 cm) from base of SlideDriver chassis if using XtremeDrive™ wheels. Review SlideDriver Standard and Slow Down Limit Ramps on page 24. AdvanceDrive™ Wheel Drive Rail (standard) Rack XtremeDrive™ Wheel XtremeDrive™ System MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 136: Drive Wheel Spring Tension (Adjustment Of Manual Release)

    Controls drive wheel gripping force. Set at 2 in. (5 cm) when Drive Wheels are Coupling Nut: clamped on the Drive Rail. Toggle handle Adjusts compression spring. is in the clamped (load) position. www.hysecurity.com © 2019 General Maintenance MX3630-01 Rev. J...

  • Page 137: Grooved Drive Rail

    NOTE: The non-grooved, flanged drive rail is still available for use with the Solenoid Lock option. The Solenoid Lock option requires an outer edge flange and therefore must be installed with the non-grooved, flanged drive rail. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 138: Drive Wheel Assembly

    Drive wheel assembly tasks are slightly different depending on the type: AdvanceDrive™ or XtremeDrive™. NOTE: Installation instructions are provided with the replacement drive wheels and are accessible online at www.hysecurity.com. A quick look at the drive wheel assembly is shown below. Tighten drive wheel mounting bolts to 25 ft lb.

  • Page 139: Hydraulic System Maintenance

    3. Fill to within ½ inch of the plug level, and then replace plug. NOTICE: Never use brake fluid. It will severely damage the hydraulic system. Use of any fluid other than fluid recommended by HySecurity may void the operator warranty. Solenoid Look for leaks: Occasionally there may be slight seeping at the fittings after some usage.

  • Page 140: Brake Valve Adjustments

    The open valve is solenoid operated and, when energized, directs the hydraulic flow to open the gate. No adjustment of this valve is possible or necessary. The black solenoid coil mounts on its valve stem. www.hysecurity.com © 2019 General Maintenance...

  • Page 141: Slidedriver Operator Maintenance Schedule

    Special Notes: *1. Your gate and gate hardware will require more maintenance than your HySecurity operator. A damaged gate or worn hardware may cause slow or erratic operation and will result in excess drive wheel wear. Lubricate gate hardware more frequently and check for smooth operation by opening the toggle clamping mechanism and then pushing the gate manually.

  • Page 142: Wiring Hysecurity Sensors: Smart Touch

    Wiring diagrams are provided on the following pages. The diagrams illustrate how to connect sensors and program the gate operator. HySecurity Smart Touch gate operators can monitor entrapment protection sensors per UL 325 - 2016 Standard of Safety using software version h4.50 (or later).

  • Page 143: Wiring Tips For Sensor Com Terminal: Smart Touch

    Press Select. Press Next or Previous. Press Select. Continue pressing Next to view Blinking characters Advance - press Next Two left characters blink. all selections. become static. Previous - press Previous MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...

  • Page 144: Smart Touch: 2 Ch Wired Edge With Hy2Nc

    FLASHING = FAULT YL = CH1 BL = CH2 OPEN +24V +24V FLASHING GREEN EDGE 2 Actively Monitoring Channel wires to 10k Edges CH 2 Wires to Edge Sensor www.hysecurity.com © 2019 Wiring HySecurity Sensors: Smart Touch MX3630-01 Rev. J...

  • Page 145: Smart Touch: Photo Eye Thru Beam (Emx Irb Mon)

    DO NOT USE 1 = OFF STATUS 2 = OFF SENSOR 3 3 = OFF 4 = ON DO NOT USE CHARGER AC LOSS HySecurity LOCK INTERLOCK MX000585 VERSION EMERG CLOSE FIRE DEPT OPEN Smart Touch Controller LIMIT DUAL GATE RADIO OPTIONS...

  • Page 146: Smart Touch: Photo Eye / Reflective (E3K R10K4)

    BLOCKED" "Photo Eye Open" PEO or "Photo Relay NO (Terminal 5, NO2) Eye Close" PEC, take steps to align the photo eye. Refer to See Photo Eye Alignment Feature on page 101. www.hysecurity.com © 2019 Wiring HySecurity Sensors: Smart Touch MX3630-01 Rev. J...

  • Page 147: Smart Touch: The Solution, Mim-62 (Multi-Input Module)

    VEHICLE DETECTOR SENSOR 1 SENSOR DO NOT USE SENSOR 2 DO NOT USE STATUS SENSOR 3 DO NOT USE CHARGER AC LOSS HySecurity LOCK INTERLOCK MX000585 VERSION EMERG CLOSE FIRE DEPT OPEN Smart Touch Controller LIMIT DUAL GATE RADIO OPTIONS OPEN...

  • Page 148: Smart Touch: Igaze Kit Wiring Diagram

    Smart Touch: iGAZE Kit Wiring Diagram www.hysecurity.com © 2019 Wiring HySecurity Sensors: Smart Touch MX3630-01 Rev. J...

  • Page 149: Slidedriver Installer Checklist

    SlideDriver Installer Checklist This check list is provided by HySecurity and is to be used after installing a SlideDriver gate operator. 1. Before checking the items in this list, make sure power is turned OFF at the main power disconnect and the operator’s control box power switch is also in the OFF position.
  • Page 150 ‰ WARNING placards mounted on both sides of the gate within sight of vehicle and pedestrian traffic per UL 325 standards. 8. Sensors programmed properly. Date: Operator Serial Number: ____________________________________________________________________ Installer Name (please print): _________________________________________________________________ End user’s name (please print): ________________________________________________________________ Site address: _______________________________________________________________________________ ___________________________________________________________________________________________ ___________________________________________________________________________________________ ___________________________________________________________________________________________ Notes: ____________________________________________________________________________________ ___________________________________________________________________________________________ www.hysecurity.com © 2019 MX3630-01 Rev. J...

  • Page 151: Appendix A - French Translations

    7. La voie d’accès est réservée aux véhicules 7. The entrance is for vehicles only. Pedestrians seulement. Les piétons doivent utiliser une voie must use separate entrance. d’accès différente. 8. SAVE THESE INSTRUCTIONS. 8. CONSERVEZ CES INSTRUCTIONS. MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 152 éloignées l’une de l’autre. Les barrières battantes Swinging gates shall not open into public access ne doivent pas ouvrir dans une zone d’accès areas. public. www.hysecurity.com © 2019 MX3630-01 Rev. J...
  • Page 153 2.11 For a gate operator utilizing a contact 2.11 Pour les ouvre-barrières qui fonctionnent sensor avec des capteurs MX3630-01 Rev. J SlideDriver/SlideDriver 50VF Series © 2019 www.hysecurity.com...
  • Page 154 à l’un des points de sa trajectoire, au moins contact sensors shall be located on the bottom un capteur de contact doit être situé sur le bord edge. inférieur. www.hysecurity.com © 2019 MX3630-01 Rev. J...
  • Page 155 HySecurity, and the Two Year warranty period in (b), (d), (e), and (f) will not extend force majeure. This warranty does not cover any incidental expenses, including fines beyond four years from the date that the product was shipped from HySecurity.

  • Page 156: Specifications

    To enable fully automatic operation, this gate operator requires a MINIMUM of one external entrapment protection sensor to monitor potential entrapment zones in either the open or close direction of travel. Visit www.hysecurity.com/gatesafety for more information on UL 325 standards and gate safety Copyright Notice ©...

This manual is also suitable for:

Slidedriver 30fSlidedriver 200Slidedriver 40Slidedriver 50vf2/3Slidedriver 80Slidedriver 50vf

Table of Contents

Save PDF