Table of Contents
Advertisement
4.4.1
Hanging on the wall 800/500-650-IIL, -IIR and -III
The appliance can be wall-mounted with the optional wall bracket
(see fig. 1.8).
4.5
Installing the flue materials
•
When penetrating a non-combustible wall or ceiling the
opening must be at least 5mm larger than the diameter of the
discharge material. At a combustible wall or ceiling is this
100mm larger than the diameter of the drainage material.
•
Horizontal sections should be installed with a slope towards
the fire (3 degrees).
•
Build the system from the fire. If this is not possible you can
make use of an extendable adapter section.
•
For truing up the exhaust system use the 0,5m. pipe, which
can be shortened and ensure that the inner pipe is always
2cm longer than the outer pipe.
•
Parts, which are shortened, must be secured with a
self-tapping screw.
•
Wall and roof terminals can also be cut.
•
Do not insulate but ventilate built-in flue material (approx.
100cm²).
4.6
Constructing the false chimney
If possible, carry out a performance test at the fire before finally
finishing the installation.
4.6.1
False chimney
*
Construct the false chimney of non-combustible material in
combination with metal profiles or of masonry/concrete
blocks.
*
Be aware of ventilation grids and service door (see fig. 1.0 to
1.5). Place above the ventilation grids a screen plate made of
non-combustible material (see fig. 1.1, 1.3 or 1.5)
*
Always use a lintel or reinforcing bars while bricking the
outlet. They should not be placed directly on the fire.
*
Built the false chimney against the appliance (see fig. 1.0 to
1.5). Keep a minimum distance of 2mm between the false
chimney and the appliance, because of the extension of the
appliance.
4.6.2
Installation and finishing
For installation and finishing the following points are of interest:
H = moldings (fig. 2.4 and 2.7)
I = distance profile (fig. 2.4)
J = upper side flange combustion chamber (fig. 2.5)
K = distance holder/glass support (fig. 2.6)
L = distance holder/glass support (fig. 2.6)
>
Please note:
Ensure that the fire is not load-bearing with regard to the false
chimney breast.
4.6.3
Method I with cover strip (fig. 2.2)
Build the false chimney breast or plateau against the moldings H
and distance profiles I (see fig. 2.4 and 2.7).
Keep a minimum distance of 2mm between the false chimney and
the appliance, because of the extension of the appliance. Take into
account the thickness of the finish!
4.6.4
Method II with built-in strip (fig. 2.3)
Remove the distance profiles "I" (see fig. 2.4).
Make sure that the screws of the front distance profile "I" will be
replaced, in order to ensure the air tightness of the appliance.
Build the plateau against the glass supports K and L (see fig. 2.6).
Keep a minimum distance of 2mm because of the extension of the
appliance.
For the height of the plateau see point "J" (fig. 2.5).
5 Removing the glass
5.1
Removing the glass from the front
MatriX 800-I:
•
Remove the moldings "A" left and right (fig. 3.0).
•
Turn the left and right side clamps "B" up (fig. 3.0).
•
Place the suction cups on the glass and slide the upper list
"C" up (fig. 3.1).
•
See fig. 3.2, number:
1.
Slide the glass to the top so that the bottom will
release.
2.
Now, carefully slide the glass to the left.
3.
Get the released side towards to you and put the glass
on a safe place.
MatriX 800-II:
•
Remove molding "A" left or right (fig. 3.0).
•
Turn the left or right side clamps "B" up (fig. 3.0).
•
Place the suction cups on the glass and slide the upper list
"C" up (fig. 3.3).
•
See fig. 3.3, number:
1.
Slide the glass to the top so that the bottom will
release.
2.
Now, carefully slide the glass to the left or to the right.
3.
Get the released side towards to you and put the glass
on a safe place.
MatriX 800-III:
•
Place the suction cups on the glass and slide the upper list
"C" up (fig. 3.3).
•
See fig. 3.3, number:
1.
Slide the glass to the top so that the bottom will
release.
4.
Get the released side towards to you and put the glass
on a safe place.
1 5
I n s t a l l a t i o n I n s t r u c t i o n s
Advertisement
Table of Contents
