Harvest TEC 300RBC Operation Manual

Moisture only kit for round balers
Hide thumbs Also See for 300RBC:

Advertisement

Operation Manual
Model 300RB & 300RBC
Moisture Only Kit for Round Balers
Forage Harvester
300RB & 300 RBC-16-OPR
11/19
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 300RBC and is the answer not in the manual?

Questions and answers

Summary of Contents for Harvest TEC 300RBC

  • Page 1 Operation Manual Model 300RB & 300RBC Moisture Only Kit for Round Balers Forage Harvester 300RB & 300 RBC-16-OPR 11/19...
  • Page 2 (intentionally blank)
  • Page 3: Table Of Contents

    Manual Mode Setup Mode Job Records Software Versions Baling Rate Settings Automatic Mode Manual Mode Job Records Wiring Diagram – 300RB Wiring Diagram – 300RBC Maintenance & Winter Storage Common Questions Troubleshooting iPad Troubleshooting Pin Outs 22-23 Parts Breakdown 24-27...
  • Page 4: Introduction

    Introduction Congratulations and thank you for purchasing a Harvest Tec Model 300RB or 300RBC moisture only kit. Please read this manual carefully to ensure correct steps are taken to attach the system to the baler. A parts break of the system is located in the back of the manual.
  • Page 5: Operation

    4. Select an available network when detected by the iPad, shown in area above that currently says ‘Other’. 5. Select App Store icon (below) and open. *You will need a Wi-Fi connection available to view App Store. **The Harvest Tec system WILL NOT appear under the Bluetooth tab in the Setting App.
  • Page 6: Ipad Integration Control Module

    030-6672C iPad Integration Control Module To operate the applicator, connect the iPad cord to the iPad Integration Control in the port indicated by: iPad Integration Control Light Signals Green Slow Blink – Power supplied to the applicator system and the unit is going through its startup process.
  • Page 7: Shutting Down The Hay App

    Shutting Down the Hay App To shut down the Hay App double click the home button (Figure A). This will show the open apps that are running on your iPad (Figure B). *Note: By pressing the home button one time to return to the home screen, the Hay App does not shut down. The system will however, stop applying preservative after 10 seconds.
  • Page 8: Operation The Hay App

    Operating the Harvest Tec iPad App (continued) When ready to operate your applicator system, open the Hay App on the iPad by selecting the Hay App icon. Device Selection The app will open to the Device Menu screen as shown below.
  • Page 9: Demo Mode

    Operating the Harvest Tec iPad App (continued) Demo Mode Selecting the 300 Demo or 600 Demo button (below) will allow you to view the different screens of the applicator without requiring connection to an applicator system. *This function is intended to be used as a visual aid, no values will be displayed.
  • Page 10: Tab Descriptions

    Operating the Harvest Tec iPad App (continued) Once you have selected the baler you want to connect with from the Device Menu, the applicator main menu will display (below). Tab Descriptions Automatic Mode: This mode allows you to use all of the applicator features such as adjusting preservative application on the go and counting total pounds of product used.
  • Page 11: Screen Menus

    Screen Menus Use the screen shots below to navigate through the operation screens. Automatic Mode Bluetooth Connection Indicator Green -THS is connected Yellow -THS connecting -THS not connected *Actual, Target, and # Used will read 0 with moisture only system Manual Mode Bluetooth Connection Indicator Green...
  • Page 12: Setup Mode

    Setup Mode If using a fixed chamber baler, Adjust the moisture default to the select the X to turn on moisture of the last bale reading *Select X to turn on options shown Indicates Crop Eyes are ON Adjust moisture alarm to desired level Select desired alarm moisture Adjust bale weight information Select desired bale weight...
  • Page 13: Job Records

    Job Records Select New Job to create new job Type in Field Name, press Create Job Select Job Details to view Select the Up and Down arrows job records to view different jobs Software Versions *This is an example, Software Versions will change...
  • Page 14: Baling Rate Settings

    Baling Rate Settings – Round Balers iPad Operation 1. On the setup mode screen press the BALING RATE key. 2. Press the grey number value to the right of AVG Bale Weight (Lbs). To adjust the weight of your bales, the scroll tool shown on the right will display.
  • Page 15: Automatic Mode

    Operation Instructions Automatic mode will allow you to view the moisture information and baling rate. Automatic Mode After pushing the AUTOMATIC MODE key in the Main Menu screen, the following screen will appear: iPad 1. To pause the unit while in operation select the Pause key. 2.
  • Page 16: Manual Mode

    Manual Mode After pushing the MANUAL MODE key in the Main Menu screen, the following screen will appear: iPad 1. To pause the unit during operation select the Pause key. 2. Push the OVERRIDE key to turn on the pump for full output of the system. This function is not used with a moisture only unit.
  • Page 17: Job Records

    Job Records After pushing the JOB RECORDS key in the Main Menu screen, the following screen will appear: 1. The job number will be displayed at the top center. The current job being viewed will always read "Job #: 0". Product used and average moisture content will be reset when the NEW JOB key is pressed. The job records screen will store up to 300 jobs allowing access previous jobs by using the up and down arrows.
  • Page 18: Wiring Diagram - 300Rb

    The power harness must be connected to the battery! The unit will draw more amps than convenience outlets can handle. Any modifications of the power harness will void systems warranty. CONTACT HARVEST TEC BEFORE MODIFICATIONS. b. This unit will not function on positive ground tractors.
  • Page 19: Wiring Diagram - 300Rbc

    The power harness must be connected to the battery! The unit will draw more amps than convenience outlets can handle. Any modifications of the power harness will void systems warranty. CONTACT HARVEST TEC BEFORE MODIFICATIONS. b. This unit will not function on positive ground tractors.
  • Page 20: Maintenance & Winter Storage

    Maintenance Dielectric Grease Connections: Disconnect all harnesses on the applicator, clean the connections, and repack with dielectric grease. Battery Connections: Follow the batteries safety warnings and clean the battery connections. If the connections cannot be cleaned, replace harness. Winter Storage Disconnect power from the Three Hundred Series controller (THS).
  • Page 21: Ipad Troubleshooting 221

    -Refer to your iPad owner’s manual or contact Apple. How do I send in my iPad for service? DO NOT SEND iPad TO HARVEST TEC. For other issues refer to your iPad Owner’s Manual or contact Apple Directly *Harvest Tec Does Not Service iPads*...
  • Page 22: Pin Outs

    Pin Outs Power Harness 006-3650T at Tractor Hitch Pin 1 Red +12V Power to BLE Pin 2 Red +12V Power to THS Pin 3 Orange Keyed Power Pin 4 Not Used Pin 5 Green HT Can Low Pin 6 Yellow HT Can Hi Pin 7 Not Used Pin 8 Black...
  • Page 23 Pin Outs (continued) End of Row Sensor at 300 Controller Harness Pin 1 Red/White +12V Power Pin 2 Black/White Ground Pin 3 Yellow Signal Pin 4 N/A Moisture Sensor connection at 300 Controller Harness Pin 1 Not Used Pin 2 Not Used Pin 3 Not Used Pin 4 Not Used Pin 5 Not Used...
  • Page 24: Parts Breakdown

    Control Box and Wiring Harnesses Description Part # Tractor Power Harness 006-3650T iPad Integration Control 030-6672C Baler Power Harness (20’) 006-3650B1 Control Box 006-3671RB Dust Plug Kit 006-5651Plug Key Switch Harness 006-5650K USB Cable 006-6672USBC Complete Assembly 030-363CPA End of Bale Sensor Kit A Ref Description Part # End of Bale Sensor...
  • Page 25: Moisture Pads

    006-4641H Plastic Bushing 006-4641G Moisture Cable 006-4640G2 Moisture Pad Assembly (Ref 1-5) 030-4643 Complete Assembly (Ref 1-6) MSH-RB-A Moisture Sensor – 300RBC Description Part # Description Part # 1/2" x 4 1/2” Carriage Bolt RB Isolator 006-4641FX Hardware RB Moisture Pad...
  • Page 26: Optional Ipad Display Kit

    Optional iPad Display Kit (030-4670DK) Description Part # Ref Description Part # Suction cup mount 001-2012SCM iPad Mini Charger 12V 001-2012P Ram mount 001-2012H iPad Mini 4 case 001-2012C4 ® iPad Mini spring load 001-2012SLC iPad Mini 4 006-4670IP cradle (Mini 4) 16 gauge power wire 006-4723P 4 amp fuse...
  • Page 27: Warranty Statement

    Harvest Tec, Inc. within 30 days of the failure. If it is determined that a non-Harvest Tec branded hay preservative has been used inside the Harvest Tec applicator system where the failure occurred, then Harvest Tec reserves the right to deny the warranty request at their discretion.
  • Page 28 HARVEST TEC, INC. P.O. BOX 63 2821 HARVEY STREET HUDSON, WI 54016 PHONE: 715-386-9100 1-800-635-7468 FAX: 715-381-1792 Email: info@harvesttec.com...

This manual is also suitable for:

300rb

Table of Contents