Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operating Manual
Advertisement
Table of Contents
Related Manuals for Harvest TEC 600BB
Summary of Contents for Harvest TEC 600BB
- Page 1 Installation Manual Model 600BB Moisture Sensor Kit for Large Square Balers For New Holland BigBaler and Case IH LB 4 Forage Harvester 600BB-17-INST-Imp&Metric 5/18...
- Page 2 European Parliment and the Council of 17 May 2006 and other applicable European Directives including Directive 2004/108/EC on the Electromagnetic compatability. The application of preservatives for hay Harvest Tec system will be turned on after being installed on a farm press has been declard in conformity with the Machinery Directive.
-
Page 3: Table Of Contents
Harvest Tec Model 600BB Installation Table of Contents PAGE Introduction System Requirements Tools Needed Installation of the 600BB Moisture Sensor Kit Mounting the 600BB Dual Channel Processor (DCP) Installation and Routing Wire Harnesses and Baler Interface Harness Installation of Bluetooth Receiver... -
Page 4: Introduction
Introduction Thank you for purchasing this 600BB Moisture Sensor Kit. The 600BB Moisture Sensor Kit is designed to operator through the baler’s ISOBUS system and/or an Apple iPad (not included) using the Hay App. The 600BB Moisture Sensor offers these advantages: 1. -
Page 5: Installation Of The 600Bb Moisture Sensor Kit
Installation of the 600BB Dual Channel Processor (DCP) Figure 1 Figure 2 Figure 4 Figure 3 1. Locate the Dual Channel Processor (DCP) 006-6671LS. 2. Lock the baler flywheel brake and lift open the front hood. 3. Locate the four holes by the fly wheel brake (Figure 1). -
Page 6: Installation And Routing Wire Harnesses And Baler Interface Harness
Installation and Routing Wire Harnesses and Baler Interface Harness Route harnesses along inside of the baler (Left). Keep harnesses away from moving parts and hydraulic hoses. Secure with existing cable clamps or use cable ties. When all connections are made to the DCP secure wires as shown above to allow for water to be shed away from the DCP. -
Page 7: Installation Of The Star Wheels
Installation of Star Wheel Moisture Sensors Figure 5 Figure 6 1. Locate the two star wheel moisture sensors (030-4641) and twine diverters (001-4644 & 001-4645). 2. Directly behind the knotters, locate the four predrilled holes per side shown at the arrows. This location is also beneath the lift points on top of the baler (Figure 5). -
Page 8: Installation Of Star Wheel And Bale Rate Harness
Installation of Star Wheel and Bale Rate Harness First, remove the cover from the star wheel block and use a 1/4” nut driver to remove the nut from the electronic swivel. Next, run the star wheel sensor wire through the black grommet and place the eye terminal on the star wheel sensor. -
Page 9: Wiring Diagram
Wiring Diagram A. The Baler Power/Communication Harness (006-6650LS(E)) will attach to the open port of the Tractor Harness (006-6650TM(E)) and run back to the Dual Channel Processor (006-6671LS(E)). B. Connect the large plug of the Baler Power/Communication Harness (006-6650LS) to the bottom (shorter side) of the DCP. -
Page 10: Pin Outs
Pin Outs Power/Comm Harness 006-6650TM(E) at Hitch Pin 1 Red +12V Power to TSD Pin 2 Red +12V Power to DCP Pin 3 Orange Keyed Power Pin 4 Gray Shield Pin 5 Green HT Can Low Pin 6 Yellow HT Can Hi Pin 7 Orange Can1 Hi Pin 8 Black... - Page 11 Pin Outs (continued) 006-6650VA to 006-6650LS(E) Pin 1 Red Can Power Pin 2 Black Can Ground Pin 3 Yellow HT Can Hi Pin 4 Gray Shield Pin 5 Green HT Can Low Pin 6 N/A Pin 7 N/A 006-6650VA Harness to Baler Plug Pin A N/A Pin B Red TBC Power...
-
Page 12: Common Questions
Common Questions 1. How do I turn the system on/off? To turn the system ON open the Hay App, then select the active system for the baler you are using. Press the Wake Up tab if the system was put into Standby mode when last used. If not in Standby mode, select Automatic or Manual mode to begin. -
Page 13: Troubleshooting
5. Short in wire between star 5. Replace wire. wheels and DCP. 6. Check hay with hand tester 6. Contact Harvest Tec if conditions to verify. persist. Moisture readings erratic. 1. Test bales with hand tester to verify that DCP has more variation than hand tester. -
Page 14: Parts Breakdown
Parts Breakdown 600BB Series Controls and Harnesses Dual Channel Processor (DCP) Ref Description Part Number End of Bale Sensor 600 Series 006-7400 End of Bale Sensor Bracket 001-4648 Terminating Connector 600 Series w/green cap 006-5650Z DCP Shield/Cover 001-5650X DCP Main Control LS 600 AUTO... -
Page 15: Star Wheel Sensors
Star Wheel Moisture Sensor and Bale Rate Sensors Ref Description Part Number Qty Description Part Number Qty Block cover 006-4641B Star wheel block 006-4641A Electronic swivel 006-4642A Star wheel sensor 030-4641C Swivel insert w/ Ref # 10 Twine guard-left 001-4645 Snap ring (per side) 006-4641K Twine guard-right (prox) 001-4644... -
Page 16: Optional Ipad Mini Mounting Kit (030-2014Mk)
Optional iPad Mini Mounting Kit (030-2014MK) Description Part # Suction cup mount 001-2012SCM Ram mount 001-2012H iPad Mini spring load cradle (Mini 1,2,3) 001-2012SLC 16 gauge power wire 006-4723P Female spade connector Hardware Eye loop connector Hardware iPad Mini Charger 12V 001-2012P iPad Mini 4 case 001-2012C4... -
Page 17: Optional Ipad Display Kit (030-4670Dk)
Optional iPad Display Kit (030-4670DK) Description Part # Ref Description Part # Suction cup mount 001-2012SCM iPad Mini Charger 12V 001-2012P Ram mount 001-2012H iPad Mini 4 case 001-2012C4 iPad Mini spring load 001-2012SLC iPad Mini 4 006-4670IP cradle (Mini 1,2,3) 16 gauge power wire 006-4723P 4 amp fuse... -
Page 18: Notes
Notes... -
Page 19: Warranty
Harvest Tec, Inc. within 30 days of the failure. If it is determined that a non-Harvest Tec branded hay preservative has been used inside the Harvest Tec applicator system where the failure occurred, then Harvest Tec reserves the right to deny the warranty request at their discretion. - Page 20 HARVEST TEC, INC. P.O. BOX 63 2821 HARVEY STREET HUDSON, WI 54016 PHONE: 715-386-9100 1-800-635-7468 FAX: 715-381-1792 Email: info@harvesttec.com...