1. Manuals
  2. Brands
  3. Harvest TEC Manuals
  4. Farm Equipment
  5. 491BB
  6. Installation manual

Harvest TEC 491BB Installation Manual

15 gallon preservative applicator for new holland bigbaler and case ih lb 4
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation Manual
Model 491BB
115 Gallon Preservative Applicator
For New Holland BigBaler and Case IH LB 4
Forage Harvester
#010-0491BB-INST
Revised 04/14

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 491BB and is the answer not in the manual?

Questions and answers

Related Manuals for Harvest TEC 491BB

Summary of Contents for Harvest TEC 491BB

  • Page 1 Installation Manual Model 491BB 115 Gallon Preservative Applicator For New Holland BigBaler and Case IH LB 4 Forage Harvester #010-0491BB-INST Revised 04/14...
  • Page 2 (Intentionally blank)

  • Page 3: Table Of Contents

    Harvest Tec Model 491 Installation Table of Contents Page number Introduction Installation Kit Reference Chart Tools Needed Installation of Applicator 5-11 1. Removal of tank straps and tank 2. Installation of saddle legs and saddle 3. Installation of pump and handrail 4.

  • Page 4: Introduction

    This applicator is designed to apply Harvest Tec buffered propionic acid. The model 491 base kit includes the following parts: Tank, Frame, Pump, Hose, and Miscellaneous Hardware. The applicator is designed for New Holland BB 330-340 & Case IH LB 334-434 balers.

  • Page 5: Installation Of Applicator

    Installation of Applicator . Removal of tank straps and tank 001-6707P 001-6707P 001-6707HR Figure 1 001-6707Q 003-EL3412 001-6707N 001-6707MR 001-6707ML 1. Remove the two tank straps (001-6707P) by removing all eight 3/8” hex nuts. Figure 1 2. Lift the tank (005-9218) away from the saddle (001-6707N) and place the tank on a smooth flat surface. 3.

  • Page 6: Installation Of Saddle Legs And Saddle

    2. Installation of saddle legs and saddle 001-6707MR 001-6707ML Figure 2 Figure 3 1. Locate parts bag 5. 2. Install the two saddle legs (001-6707MR & 001-6707ML) on to the top of the baler chute as shown. Figure 2 3. Secure the two legs with six (three per side) 1/2” x 1-3/4” carriage bolts, flats washers, locks washers, and hex nuts.

  • Page 7: Installation Of Pump And Handrail

    3. Installation of pump and hand rail 001-6707HR Figure 4 001-6707Q & Pump 1. Locate parts bag 5. 2. Install the handrail (001-6707HR) above the pump manifold using two 3/8” x 3/4" flange bolts. Figure 4 3. Install the pump bracket to the tank using four 3/8” x 3/4” flange bolts. 4.

  • Page 8: Installation Of The Spray Shield

    4. Installation of the Spray Shield Assembly Installation Kits 4533 (for 3 ft wide) & 4534 (for 4 ft wide) for Standard and Packer Balers 001-4435NCX 001-4435NSX Figure 15 1. Locate the flat steel directly above the stuffer forks. Figure 15, Point A 2.

  • Page 9: For Roto-Cutter Balers

    Installation Kits 4535 (for 3 ft wide) & 4536 (for 4 ft wide) for Roto-Cut Balers 001-4435NC 001-4435NSX Figure 16 1. Locate the baler cross member directly above the rotor (figure 16 point A). 2. Locate the four pre-drilled holes on the cross member (figure 16 point B). 3.

  • Page 10: Installation Of Gauge And Hose

    5. Installation of gauge and hose 1. Locate parts bag 13. 2. Place the gauge on the upper right corner of the baler, a place that is visible form the seat of the tractor. 3. Next, run the hose from the pump outlet to the hose fitting on the gauge. Then cut the hose to length. Place hose clamps on hose ends.

  • Page 11: Installation Of Controls

    7. Installation of the Controls Route the wire to the starter solenoid on all 12v tractors. Connect the green lead marked + to the hot terminal on the starter. Connect the black lead to a good ground. Do not reverse the leads. Be sure to use a voltmeter to verify that you do have 12 volts running to the box.

  • Page 12: Parts Breakdowns

    Parts Breakdown Tank, Saddle & Saddle Legs Description Part# Description Part# Tank 005-9218 Right saddle leg 001-6707MR 1/2" tank fitting 005-9104 1/2" hose 002-9001 Elbow 003-EL1212 Elbow 003-EL3434 Tank straps 001-6707P Elbow 003-EL3412 Tank saddle 001-6707N Tank lid strainer 005-9022HBS Handrail 001-6707HR 3/4"...

  • Page 13: Control Box, Wiring Harnesses, Gauge, And Pump Assembly

    Control Box and Wiring Harnesses, Gauge, and Pump Assembly Description Part# Description Part# Control box 030-0457 Gauge 002-2208Z Speed control 006-2022 Gauge holder 001-4717 Power cord 006-4580C Tee fitting 003-TT14 Pump lead 006-4583 Elbow fitting 003-EL1412 Knobs 008-0923 Straight fitting 003-A1412 U-Bracket 001-2012E...

  • Page 14: Installation Kits: Baler Specific

    Harvest Tec Model 4533 and 4534 Installation Kit (4534 pictured) (4533 has shorter EVA tube between Manifold Blocks) Ref Description Part # Qty Ref Description Part # Holder 001-4435NCX 1 11 Fitting 003-A1412 Shield 001-4435NSX 1 12 Lynch Pin 008-4576 Hose-1/2”...
  • Page 15 Harvest Tec Model 4535 and 4536 Installation Kit (4536 pictured) (4535 has shorter EVA tube between Manifold Blocks) Description Part # Qty Ref Description Part # Shield 001-4435NSX 1 11 Tip-Yellow 004-T8005-PT Holder 001-4435NC 1 12 Tip-Pink 004-T8001-PT Hose – 1/2"...

  • Page 16: Notes

    NOTES:...
  • Page 17 NOTES:...
  • Page 18 NOTES:...

  • Page 19: Warranty Statement

    WARRANTY AND LIABILITY AGREEMENT Harvest Tec, Inc. will repair or replace components that are found to be defective within 12 months from the date of manufacture. Under no circumstances does this warranty cover any components which in the opinion of Harvest Tec, Inc. have been subjected to negligent use, misuse, alteration, accident, or if repairs have been made with parts other than those manufactured and obtainable from Harvest Tec, Inc.
  • Page 20 HARVEST TEC, INC. P.O. BOX 63 2821 HARVEY STREET HUDSON, WI 54016 PHONE: 715-386-9100 1-800-635-7468 FAX: 715-381-1792 Email: info@harvesttec.com...

Table of Contents