Related Manuals for Harvest TEC 600RBC
Summary of Contents for Harvest TEC 600RBC
- Page 1 Installation Manual Model 600RBC Moisture Sensor Kit for Roll-Belt Round Balers Forage Harvester 600RBC-16-INST-Imp&Metric 5/18...
- Page 2 Council of 17 May 2006 and other applicable European Directives including Directive 2004/108/EC on the Electromagnetic compatability. The application of preservatives for hay Harvest Tec system will be turned on after being installed on a farm press has been declard in conformity with the Machinery Directive.
-
Page 3: Table Of Contents
600RBC Installation Manual Table of Contents Page Introduction System Requirements Tools Needed Installation of Moisture Sensor Installation of Dual Channel Processor (DCP) Installation of Moisture Sensor Pads Installation of Bale Rate Timer Sensor Wiring Diagram Pin Outs 9-10 Common Questions... -
Page 4: Introduction
Monitoring System has been designed to be operated through an Apple iPad (not included) using the Hay App. As well as the option to plug directly into most tractors that have an ISOBUS Monitor. The 600RBC Moisture Monitoring System offers these advantages by operating through an Apple iPad: 1. -
Page 5: Installation Of Moisture Sensor
Installation of Dual Channel Processor (DCP) 1. Locate mounting bolts on support bar of right side of baler (Figure 1). 2. Install DCP mounting bracket 001-4703XI as shown (Figure 2). 3. Install DCP onto mounting bracket 001-4703XI and secure (Figure 3). 4. -
Page 6: Installation Of Moisture Sensor Pads
Installation of Moisture Sensing Pads 1. Open rear tail gate of baler and lock in the up position. Refer to baler manual to lock door open. 2. Remove bale shaping discs on each side of chamber by grinding welds. Once removed grind any remaining welds so sides of bale chamber are smooth. -
Page 7: Installation Of Bale Rate Timer Sensor
Installation of Moisture Sensor Pads and Disks (continued) USR (under-shot rotor) OSR (over-shot) rotor) Installation of Bale Rate Timer Sensor The bale rate timer sensor is used to determine when the baler door is open. With this information the system is able to change the tons/hour automatically. -
Page 8: Wiring Diagram
The power harness must be connected to the battery! The unit will draw more amps than convenience outlets can handle. Any modifications of the power harness will void systems warranty. CONTACT HARVEST TEC IF MODIFICATION IS REQUIRED! b. This unit will not function on positive ground tractors. -
Page 9: Pin Outs
Pin Outs Power/Comm Harness 006-6650TM(E) at Hitch Pin 1 Red +12V Power to TSD Pin 2 Red +12V Power to DCP Pin 3 Orange Keyed Power Pin 4 Gray Shield Pin 5 Green HT Can Low Pin 6 Yellow HT Can Hi Pin 7 Orange Can1 Hi Pin 8 Black... - Page 10 Pin Outs (continued) Main Power Connector on DCP Pin 1 Red +12V Power from tractor Pin 2 Black Ground from tractor Pin 3 Orange Keyed power Star Wheel and Bale Rate Sensor connector on DCP Pin 1 Blue +12V Power Pin 2 Orange Ground Pin 3 Black...
-
Page 11: Common Questions
BMP. 5. Short in wire DCP-disc 5. Replace wire. 6. Check with hand tester 6. Contact Harvest Tec if no change Moisture readings erratic. 1. Test bales with hand tester to verify that cab monitor has variance 2. -
Page 12: Parts Breakdown
Parts Breakdown for 600RBC Series Control and Harnesses Ref Description Part Number End Of Bale Sensor 006-7400 Terminating Connector w/ green cap 006-5650Z DCP Shield/Cover 001-5650X DCP Main Control LS 600 AUTO 006-6671RB DCP Baler Harness 15 FT 006-6650LS DCP Tractor Harness... -
Page 13: Moisture Pads
Moisture Pads Parts Breakdown Description Part # CNH RB Moisture Isolator 006-4641FX CNH RB Moisture Disk 006-4641HX 1/2” JAM Nut Misc Hardware 1/2" Lock Misc Hardware 1/2" D Washer Misc Hardware 1/2"x 4” Bolt Misc Hardware Sensor Bushing 006-4641G Sensor Isolator 006-4641I Moisture Cable 006-4640G3... -
Page 14: Optional Ipad Mini Mounting Kit (030-2012Mk)
Optional iPad Mini Mounting Kit (030-2014MK) Description Part # Suction cup mount 001-2012SCM Ram mount 001-2012H iPad Mini spring load cradle (Mini 1,2,3) 001-2012SLC 16 gauge power wire 006-4723P Female spade connector Hardware Eye loop connector Hardware iPad Mini Charger 12V 001-2012P iPad Mini 4 case 001-2012C4... -
Page 15: Optional Ipad Display Kit (030-2670Dk)
Optional iPad Display Kit (030-4670DK) Description Part # Ref Description Part # Suction cup mount 001-2012SCM iPad Mini Charger 12V 001-2012P Ram mount 001-2012H iPad Mini 4 case 001-2012C4 iPad Mini spring load 001-2012SLC iPad Mini 4 006-4670IP cradle (Mini 1,2,3) 16 gauge power wire 006-4723P 4 amp fuse... -
Page 16: Notes
Notes... - Page 17 Notes...
- Page 18 Notes...
-
Page 19: Warranty
Harvest Tec, Inc. within 30 days of the failure. If it is determined that a non-Harvest Tec branded hay preservative has been used inside the Harvest Tec applicator system where the failure occurred, then Harvest Tec reserves the right to deny the warranty request at their discretion. - Page 20 HARVEST TEC, INC. P.O. BOX 63 2821 HARVEY STREET HUDSON, WI 54016 PHONE: 715-386-9100 1-800-635-7468 FAX: 715-381-1792 Email: info@harvesttec.com...
Need help?
Do you have a question about the 600RBC and is the answer not in the manual?
Questions and answers