J275 2K Ha; Intended Use; Limitations Of Use; Unauthorised Use - FAAC J275 2K HA Manual

3. J275 2K HA

3.1 INTENDED USE

The J275 2K HA, is an automatic hydraulic bollard designed for pe-
rimeter protection applications.
Installations using the J275 2K HA must be used for vehicular traffic.
To lower the bollard manually, follow the instructions in § 4.6.
!
Any other use that is not expressly specified in these instructions is
prohibited and could affect the integrity of the product and/or represent
a source of danger.

3.2 LIMITATIONS OF USE

Comply with the limitations on frequency of use listed in the techni-
cal data section.
The presence of snow, ice and strong wind, even occasional, could
affect the operation of the automation, the integrity of the com-
ponents and become a potential source of danger (see section §

Emergency use).

The J275 2K HA must be connected to a FAAC JE275 electronic board.
Implementing the automation requires the installation of the neces-
sary safety devices, identified by the installer through an appropriate
risk assessment of the installation site. The installation must be visible
during the day and at night. If it is not, appropriate solutions must be
provided in order to make the fixed and moving parts visible .

3.3 UNAUTHORISED USE

- Uses other than the intended use are prohibited.
- It is prohibited to install the automation outside of the limits
specified in the Technical Data and Installation Requirements
sections.
- It is prohibited to use the J275 2K HA in a configuration other
than the one intended by the manufacturer.
- No component part of the product may be modified.
- It is prohibited to install the automation on escape routes.
- It is prohibited to install the automation in environments in which
there is a risk of explosion and/or fire: the presence of flamma-
ble gases or fumes is a serious safety hazard (the product is not
94/9/EC ATEX certified).
- It is prohibited to power the system with energy sources other
than those specified.
- It is prohibited to integrate commercial systems and/or equip-
ment other than those specified, or use them for purposes not
intended and authorised by their respective manufacturers.
- It is prohibited to use and/or install accessories that have not
been specifically approved by FAAC S.p.A.
- It is prohibited to use the automation before performing com-
missioning.
- It is prohibited to use the automation in the presence of faults
which could compromise safety.
- It is prohibited to use the automation with the fixed and/or
mobile guards removed or altered.
- Do not use the automation unless the area of operation is free
of persons, animals or objects.
- Do not enter/remain in the area of operation of the automation
while it is moving.
- Do not try to prevent the movement of the automation.
- Do not climb or hold on to the cylinder or lift yourself up on it.
- Do not allow children to approach or play in the area of operation
of the automation.
- Do not allow the control devices to be used by anyone who is
not specifically authorised and trained to do so.
- Do not allow the control devices to be used by children or persons
with mental and physical deficiencies unless they are supervised
by an adult who is responsible for their safety.
J275 2K HA
3.4 EMERGENCY USE
In the event of a malfunction, emergency or failure, disconnect the
power supply to the automation. Place the automation out of
service until it has been reset/repaired.
In the case of a breakdown, the automation system must be reset/
repaired exclusively by the INSTALLER/MAINTENANCE TECHNICIAN.

3.5 PRODUCT IDENTIFICATION

The product can be identified by the plate (see  1 ).
J275 2K HA
••••••
MM/YY PROG
•••••• •••• ••••
•••• •••• ••••
••••••••••••••••
MMYYPROG
6
Sale code
Product name
IDENTIFICATION NUMBER
Month/year of production + progressive
number for the month of production
Example: 0117 0001
produced in January 2017 S/N 1
532208 - Rev.A
 1