Advantech B+B SmartWorx IMcV-10G User Manual
  1. Manuals
  2. Brands
  3. Advantech Manuals
  4. Media Converter
  5. B+B SmartWorx IMcV-10G
  6. User manual

Advantech B+B SmartWorx IMcV-10G User Manual

Converter sfp+/sfp+, fiber mode converter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
IMcV-10G Converter
SFP+/SFP+
Fiber Mode Converter
USER MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the B+B SmartWorx IMcV-10G and is the answer not in the manual?

Questions and answers

Related Manuals for Advantech B+B SmartWorx IMcV-10G

Summary of Contents for Advantech B+B SmartWorx IMcV-10G

  • Page 1 IMcV-10G Converter SFP+/SFP+ Fiber Mode Converter USER MANUAL...
  • Page 2 Fiber Mode Converter SFP+/SFP+ Advantech B+B SmartWorx - Americas 707 Dayton Road Ottawa, IL 61350 USA Phone (815) 433-5100 (815) 433-5105 Advantech B+B SmartWorx - Europe Westlink Commercial Park Oranmore, Co. Galway, Ireland Phone +353 91-792444 Fax +353 91-792445 www.advantech-bb.com...

  • Page 3: Table Of Contents

    iMcV-10G Fiber Mode Converter SFP+/SFP+ CONTENTS iMcV-10G-Fiber Mode Converter SFP+/SFP+ ..........4 Overview ........................4 Specifications ....................... 4 Installation Instructions ................5 Pre-Setup Steps ......................5 Electrostatic Discharge (ESD) Precautions ..............5 Installing an iMcV Module ................... 6 Install iMcV-10G-Converter SFP+/SFP+ ..............6 Managed Modules ......................

  • Page 4: Imcv-10G-Fiber Mode Converter Sfp+/Sfp

    iMcV-10G Fiber Mode Converter SFP+/SFP+ IMCV-10G-FIBER MODE CONVERTER SFP+/SFP+ OVERVIEW The iMcV-10G-Converter SFP+/SFP+ is a single-wide module that can be installed in an iMediaChassis series, a MediaChassis series or an IE- MediaChassis series. The iMcV-10G-Converter SFP+/SFP+ is a media converter module with SFP+ ports that can provide a conversion between different fiber types.

  • Page 5: Installation Instructions

    iMcV-10G Fiber Mode Converter SFP+/SFP+ INSTALLATION INSTRUCTIONS PRE-SETUP STEPS The iMcV-10G-Converter SFP+/SFP+ modules have user-configurable features: Loss Carry Forward (LCF), Speed (based on protocol selection) and Loopback. Your iMcV-10G-Converter SFP+/SFP+ has been tested for proper operation before packaging and shipping. It should be in perfect mechanical and electrical condition upon receipt.

  • Page 6: Installing An Imcv Module

    iMcV-10G Fiber Mode Converter SFP+/SFP+ INSTALLING AN IMCV MODULE The iMcV-10G-Converter SFP+/SFP+ can be installed in B+B SmartWorx' SNMP manageable iMediaChassis, MediaChassis series AC or DC, or IE- MediaChassis AC or DC. NOTE: All modules are hot swappable. INSTALL IMCV-10G-CONVERTER SFP+/SFP+ Remove the blank bracket covering the slot where the module is to be installed by removing the screws on the outside edges of the bracket.
  • Page 7 iMcV-10G Fiber Mode Converter SFP+/SFP+ When non-Configuration Control modules are placed in a managed • chassis, the module’s DIP Switches are ignored, and the module is configured by the chassis’ Management Module. If the SNMP Management Module is removed or fails, then the modules will revert back to the DIP Switch settings.

  • Page 8: Unmanaged Modules

    iMcV-10G Fiber Mode Converter SFP+/SFP+ UNMANAGED MODULES Before installing, configure the iMcV-10G-Converter SFP+/SFP+ module/s for desired features. The DIP Switch settings enable the end user to select the speed/protocol, loopback modes and Loss Carry Forward (LCF). The table below indicates the available features and settings for the iMcV-10G- Converter SFP+/SFP+ module/s.
  • Page 9 iMcV-10G Fiber Mode Converter SFP+/SFP+ Board Layout...

  • Page 10: Operation

    iMcV-10G Fiber Mode Converter SFP+/SFP+ OPERATION LOSS CARRY FORW ARD (LCF) When a fault is detected on the incoming optical line that would severely affect the quality of the corresponding output optical signal, this signal is turned OFF as opposed to sending a bad optical signal to the next unit over the optical line.

  • Page 11: Led Operation

    iMcV-10G Fiber Mode Converter SFP+/SFP+ LED OPERATION Each iMcV-10G-Converter SFP+/SFP+ features diagnostic LEDs that provide information on features and ports. Name Color Function SFP+1 Yellow ON when a DDMI fault is detected or SFP+ not installed. ON when no link is detected. Green ON when the Optical Link is good.

  • Page 12: B+B Smartworx Technical Support

    USA/Canada: 1 (800) 346-3119 (Ottawa IL USA) Europe: +353 91 792444 (Ireland / Europe) Email: support@advantech-bb.com Web: www.advantech-bb.com STATEMENTS, GUIDELINES, PRECAUTIONS, REGULATORY FCC RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A computing device, pursuant to Part 15 of the FCC Rules.

  • Page 13: Fiber Optic Cleaning Guidelines

    iMcV-10G Fiber Mode Converter SFP+/SFP+ FIBER OPTIC CLEANING GUIDELINES Fiber Optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust, which can obstruct the optic path and cause performance degradation. Good system performance requires clean optics and connector ferrules.

  • Page 14: Regulatory, Standards, Compliances

    © 2018 B+B SmartWorx – powered by Advantech. All rights reserved. The information in this document is subject to change without notice. B+B SmartWorx assumes no responsibility for any errors that may appear in this document.

Table of Contents