Related Manuals for Advantech ADAM-6541
Summary of Contents for Advantech ADAM-6541
-
Page 1: User Manual
ADAM-6541 10/100Base-TX Ethernet to 100Base-FX Multi-Mode Fiber Optic Converter User Manual... - Page 2 No part of this man- ual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reli- able.
- Page 3 Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its prod- ucts will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or...
-
Page 4: Declaration Of Conformity
This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering information. - Page 5 Step 1. Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. Step 2. Contact your distributor, sales representative, or Advantech's cus- tomer service center for technical support if you need additional assistance. Please have the following information ready before...
- Page 6 ADAM-6541 User Manual...
-
Page 7: Table Of Contents
Specifications ..............3 Ordering Information ............4 Chapter 2 Installation ............6 LED Indicators ..............6 Table 2.1:ADAM-6541 LED Definition ....... 6 Dimensions (units:mm) ............. 7 Figure 2.1:ADAM-6541-Front Panel ......7 Figure 2.2:ADAM-6541-Bottom ........7 Full / Half-Duplex Selection ..........8 Connecting the Hardware.......... - Page 8 ADAM-6541 User Manual viii...
- Page 9 Overview This chapter gives an overview of ADAM-6541 modules. Sections include: • Introduction • Features • Specifications • Ordering Information...
-
Page 10: Chapter 1 Overview
+10~30 V operating voltages are also sup- plied over the terminal block. In addition, the operating temperature ranges from -10 ~ 65° C. The above functions make the ADAM-6541 a stable and reliable industrial grade converter. High-Speed Transmissions The ADAM-6541 supports MDI/MDI-X of auto detection. -
Page 11: Features
Ethernet : up to 100 Mbps Transmission Speed Fiber : 100 Mbps Interface 1 x RJ-45 Connectors 1 x SC type fiber connector(ADAM-6541) 1 x ST type fiber connector(ADAM-6541/ST) Power, LED Indicators Full/Link(100BASE-FX), 100/10M (Ethernet) Power 2-pin removable screw terminal Power Connectors Max. -
Page 12: Ordering Information
EU : EN55011 EN55022 Class A EN61000-3-2/3 EN55024 IEC61000-4-2/3/4/5/6/8/11 1.4 Ordering Information ADAM-6541: 10/100 Base-TX Ethernet to 100 Base-FX Multi-Mode SC Type Fiber Optic Converter ADAM-6541/ST: 10/100 Base-TX Ethernet to 100 Base-FX Multi-Mode ST Type Fiber Optic Converter ADAM-6541 User Manual... - Page 13 Installation In this chapter, you will be given an overview of the ADAM-6541 hardware installation procedures. Sections include: • LED Indicators • Dimensions • Full/Half-Duplex Connections • Connecting the Hardware • Network Connection...
-
Page 14: Chapter 2 Installation
Chapter 2 Installation 2.1 LED Indicators There are six network LEDs located on the top panel of the ADAM-6541, each with its own specific function. Table 2.1: ADAM-6541 LED Definition Power Green Power is on Green Power is off Full/Link(100Base-... -
Page 15: Dimensions (Units:mm)
2.2 Dimensions (units:mm) Figure 2.1: ADAM-6541-Front Panel Figure 2.2: ADAM-6541-Bottom Chapter 2... -
Page 16: Full / Half-Duplex Selection
Half-duplex mode. You may select Full or half- duplex mode according to your equipment requirements. You can configure full or half-duplex ADAM-6541 via JP1 (located on the top-left PCB.) Description... -
Page 17: Connecting The Hardware
The ADAM-6541 can be attached to a wall using the included metal brackets. Each bracket comes with four screws. First attach the brackets to the bottom of the ADAM-6541, then screw each bracket to a wall. Figure 2.3: Figure 2-3 Panel Mounting... -
Page 18: Figure 2.4:Din Rail Mounting
DIN-rail Mounting You can mount the ADAM-6541 on a standard DIN-rail. First, using two screws, attach the metal plate to the DIN-rail bracket. Because the screw heads are beveled, the tops of the screws will be flush with the metal plate. -
Page 19: Figure 2.5:Figure2-5 Piggyback Stack
Piggyback Stack ADAM-6541 can be stacked as seen in the figure below. Figure 2.5: Figure2-5 Piggyback Stack 2.5 Network Connection 2.5.1 Connection to the devices The ADAM-6541 consists of one fiber and one RJ-45 port. Each of the converter’s twisted-pair ports can be used to connect a station or other device. -
Page 20: Connection To Other Hubs Or Switch
ADAM-6541 can be connected to other hub or switch via a two-pair straight through cable or crossover cable. The connection can be made from ADAM-6541’s ports to other Hub or Switch, such as MDI-X port or uplink MDI port. ADAM-6541 supports auto crossover to easily and flexibly network users’... - Page 21 Pin Assignments & Wiring...
-
Page 22: Figure A.1:Rj-45 Pin Assignment
It is suggested to adopt ELA/TIA as the wiring of the RJ45. Figure A.1: RJ-45 Pin Assignment 1. White, Green 2. Green 3. White, Orange 4. Blue 5. White, Blue 6. Orange 7. White, Brown Figure A.2: EIA/TIA-568B ADAM-6541 User Manual...