APPENDIX 1. Spare Parts List Atmos Multi Mk 2 Parts List Atmos Multi 24/80 Atmos Multi 24/80 PLUS Atmos Multi 32/80 PLUS Drg Ref Description Part Ref. Wall bracket 07.98.37.043 Bracket fixing kit 07.95.82.006 Rear casing 07.90.22.080 AAV Grommet 15 mm red/brown 07.98.68.026...
Page 3
Atmos Multi Mk 2 Parts List Atmos Multi 24/80 Atmos Multi 24/80 PLUS Atmos Multi 32/80 PLUS Drg Ref Description Part Ref. 78.76.54.981 Thermostat Rear insulation 07.98.83.229 Burner/fan assembly - 24 Model 07.95.25.003 07.95.25.004 Burner/fan assembly - 32 Model 19.1 Burner casting 07.95.07.002...
Page 4
Atmos Multi Mk 2 Parts List Atmos Multi 24/80 Atmos Multi 24/80 PLUS Atmos Multi 32/80 PLUS Drg Ref Description Part Ref. 07.98.35.296 Data Plate Data Plate 32 Plus Model 07.98.35.297 Screw M3x 25 07.98.82.115 07.98.66.122 Cable loom K1 (room thermostat) Cable loom K2 (pressure sensor) 07.98.66.206...
Page 5
ATMOS MULTI Mk2 version 2004 Appendix Page 5...
Page 6
ATMOS MULTI Mk2 version 2004 Appendix Page 6...
Page 7
ATMOS MULTI Mk2 version 2004 Appendix Page 7...
Page 8
ATMOS MULTI Mk2 version 2004 Appendix Page 8...
Page 9
ATMOS MULTI Mk2 version 2004 Appendix Page 9...
APPENDIX 2. Fault Finding 1. GENERAL The Atmos Multi has 3 types of error messages:- 1. Warning messages In this case, instead of the status message, a letter appears on the diagnostic display for one second, once every 5 seconds.
Appliance type recognition error, control unit is set to 24/80 Appliance type recognition error, control unit is set to 32/80 plus Appliance type recognition error, control unit is set to 32/80 * this code will not be stored in the memory ATMOS MULTI Mk2 version 2004 Appendix Page 11...
Page 12
C) appears on the central heating • Temperature sensor wiring interrupted water display. • Sensor defective • Control unit • Control heating temperature <-10 • Short circuit in temperature sensor wiring • Sensor defective • Control unit ATMOS MULTI Mk2 version 2004 Appendix Page 12...
Page 13
Appliance type recognition error, the control unit is set to 32/80 Appliance type recognition error, the control plus unit is set to 32/80 * this code will not be stored in the memory ATMOS MULTI Mk2 version 2004 Appendix Page 13...
Page 14
Ionisation signal remains too long Valve in gas valve defective, remains open or leaks • after heat supply Control unit • Gas valve control receiving voltage Wiring error • erroneously Control unit ATMOS MULTI Mk2 version 2004 Appendix Page 14...
Page 15
Plug not inserted in wall socket • display] receiving any power No electricity from wall socket • Wire loom connector k6 not connected • Control unit fuse defective • Mains voltage wiring defective • Control unit ATMOS MULTI Mk2 version 2004 Appendix Page 15...
- 8 = malfunction code etc. Blocks (maximum 16) Begin/end - 8 = service identification number (0 - 6) Last blocking code - 8 = blocking code Last blocking code -1 etc. standard ATMOS MULTI Mk2 version 2004 Appendix Page 16...
Page 17
10 kW plus 32/80 21 kW *32 kW standard only visible if outside temperature sensor is connected with the proper selection, the code t will not be visible in the service program ATMOS MULTI Mk2 version 2004 Appendix Page 17...
Page 18
Every malfunction is preceded by a service identification number. The service identification number is a handy tool for servicing the ATMOS MULTI. By changing this number after every service, the next time, one can see which blocks and/or malfunctions occurred since the last service.
Atmos gives a 1 year guarantee on replacement parts. incorrectly implemented repairs. The guarantee also Parts or appliances sent to the factory for repair or becomes null and void if changes are made to the replacement must always be sent postage paid.