Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Peco 05721201
Summary of Contents for Peco 05721201
- Page 1 P P P PTO GRASS PECO PECO PECO PECO PECO COLLECTION SYSTEM DESIGNED TO FIT: S150XT 2012-2013 MODEL #: 05721201 6.5HP BRIGGS & STRATTON VANGUARD MODEL #: 05721202 900 SERIES BRIGGS & STRATTON OPERATOR’S MANUAL ASSEMBLY OPERATION MAINTENANCE MANUAL PART#: Q0461...
-
Page 2: Table Of Contents
PECO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2... -
Page 3: Safety Alert Symbols
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later. -
Page 5: Introduction And Description
Installation for Use 2-1 Preparation Of Mower 1-1 Introduction We are pleased to have you as a PECO customer. Your On units with the Donaldson air cleaner, loosen the collection system has been designed to give you a low hardware and rotate the air cleaner to the forward-most maintenance, simple, and effective way to collect the position. -
Page 6: Left And Right Frame Bracket Installation
2-2 Left and Right Frame Bracket Installation Secure the left frame bracket P#(B0801) and right frame bracket P#(B0802) to the rear frame of the mower where the rear bumper was removed. Use the existing hardware from the rear bumper as shown in Figure 2-2. Figure 2-2 Existing Hardware... -
Page 7: Rear Frame Bracket Installation
2-3 Rear Frame Bracket Installation 2-4 Muffler Guard Bracket Installation Attach the rear frame bracket P#(B0803) to the left and Attach (2) muffler guard brackets P#(B0806) to the rear right frame bracket using (2) 3/8”-16 x 1” HHCS frame bracket using (1) 1/4”-20 x 3/4” HHCS P#(K1222) P#(K1191) and (2) 3/8”-16 nylon flange locknuts and (1) 1/4”-20 nylon flange locknut P#(K2014) PER P#(K2038). -
Page 8: Outer Engine Mount Tube Installation
2-5 Outer Engine Mount Tube 2-6 Engine Mount Arm Assembly Installation Installation Secure the outer engine mount tube P#(B3727) to the Insert the engine mount arm assembly P#(A0274) into rear frame bracket using (2) 3/8”-16 x 3” u-bolts the outer engine mount tube and secure with (1) detent P#(K1432) and (4) 3/8”-16 nylon flange locknuts pin P#(J0248). -
Page 9: Engine/Blower/Blade Assembly Installation
2-7 Engine/Blower/Blade Assembly Installation Place the engine/blower/blade assembly on top of the engine mount arm assembly as shown in Figure 2-7a. Secure the assembly using (4) 5/16”-18 x 1-1/2” HHCS P#(K1157) and (4) 5/16”-18 nylon flange lock nuts P#(K2516) as shown in Figure 2-7b. Adjust the position of the outer engine mount tube so that the blower housing has at least 1”... -
Page 10: Left And Right Frame Leg Installation
2-8 Left and Right Frame Leg Installation Attach the left frame leg P#(B0804) to the left frame bracket and the right frame leg P#(B0805) to the right frame bracket using (2) 1/2”-13 x 1” HHCS P#(K1231) and (2) 1/2”-13 nylon flange locknuts P#(K2012) PER BRACKET. -
Page 11: Lift Handle Installation
2-10 Lift Handle Installation Fasten the ball joint P#(K1442) to the end of the latch NOTE: Before continuing the lift handle installation, rod P#(A0620). Tighten the ball joint to approximately have someone assist you in turning the grass container half way down the threads on the latch rod. Attach the upside down. -
Page 12: Aluminum Grass Container Installation
2-11 Aluminum Grass Container Installation NOTE: It is recommended that (3) people assist in mounting the container. With three people available, two Figure 2-11b can lower the container onto the frame while the third person inserts the pivot pins P#(K0172) through the holes as shown in Figure 2-11a. -
Page 13: Exhaust Diverter Installation
2-13 Exhaust Diverter Installation 2-15 Boot To Mower Deck Installation Lift the grass deflector on the discharge chute. Insert (1) To prevent the engine exhaust from damaging the boot rod P#(B0348) through the outside set of mounting engine/blower/blade assembly, insert (1) exhaust holes on the deflector bracket, as shown in Figure 2-15a. -
Page 14: Length Of Hose Adjustment
2-16 Length Of Hose Adjustment 2-18 Lower Hose To Blower Cone Installation The hoses in steps 2-17 and 2-18 must be cut to fit your machine. Follow steps 2-17 and 2-18. do not cut the Slide a pre-assembled hose clamp P#(J1000) over both hoses until you have tried to fit them on your machine. -
Page 15: Impeller Blade Removal Replacement
2-20 Impeller Blade Removal/Replacement Tips on removing impeller blade; To gain impeller blade (#1) access, first remove the blower cone (#2) from the blower housing, located on 1 - Try carefully hitting the base of the impeller blade (#1), between each vein (#12), with a rubber mallet to the PTO assembly P#(A1821), by removing two blower loosen the taper-lock bushing hold. -
Page 16: Weight Kit Installation
2-21 Weight Kit Installation The collection system requires that a weight kit is Position (1) weight bar P#(B2220) on top of the weight installed to the front of the mower to counter-balance the bracket as shown in Figure 2-21b. Center the weight bar weight of the collection system, when filled with debris. -
Page 17: Throttle Cable Installation
2-22 Throttle Cable Installation Figure 2-22d To install the throttle cable kit P#(A0060) to the box assembly, align the large end of the slot in the throttle base plate (Figure 2-22a) with the rivets located on the front of the box assembly frame (Figure 2-22b). Place the throttle base plate over the rivets, Slide the throttle cable kit to the right, moving the smaller end of the slot Throttle Cable... -
Page 18: Exploded Views And Parts List
A0560 ALUMINUM GRASS CONTAINER EXPLODED VIEW... -
Page 21: Operating Instructions
(Experts recommend not cutting off more than 1/3 of been torn or worn through, replace with genuine the grass blade length at any given time.) PECO parts. * Mow twice, at different height settings, (high, then low), if grass is extra tall. -
Page 22: Parts And Service
SECTION V PARTS AND SERVICE 5-1 Parts And Service Information PECO collection system owners should record the name and telephone number of their Service Center. Your Service Center will be happy to supply replacement parts, accessories, and do any service or repairs to your collection system. -
Page 23: Safety Decals
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. # R2008 # R2007 Part #: R1057... - Page 25 P P P PECO PECO PECO PECO PECO 10 WALDEN DRIVE ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: peco@lawnvac.com WEBSITE: www.lawnvac.com...
Need help?
Do you have a question about the 05721201 and is the answer not in the manual?
Questions and answers