How To Use Your Rcu; Projector Address; How To Display A Projector Address - Barco Graphics 808s Owner's Manual

Controlling
The BARCOREALITY 812HS can be controlled with
a. The RCU
b. The hardwired RCU (cable not included)
c. The local keyboard
The procedure and results of controlling the projector with either of
these RCU options is essentially the same.

How to use your RCU

a) Point the front of the RCU towards the reflective screen surface
Ceiling
IR sensor
Screen
b) Point the front of the RCU towards one of the IR sensors in the
projector.
Front of projector
I Ã D U ! " V ! Ã P T ! S " ! @ T U S D S P H @ S
S T ! " ! ÃDI S T !" !ÃP V U DS S @ H P U @
45° 45°
) 
)  )
)  )
$ ' - ( ;,7
( 1 7 ( 5
3 $ 8 6 ( 7 ( ; 7
3+$6 (
RCU

6 + $ 5 31
 
7 , 1 7
 
& 2/ 25
 
% 5, * + 71


& 2 1 7 5
75(% / ( % $ / $ 1& (
%$ 6 6 9 2/
When using the wireless remote control, make sure you are within
the effective operating distance (30m, 100ft in a straight line). The
remote control unit will not function properly if strong light strikes the
sensor window or if there are obstacles between the remote control
unit and the projector's IR sensor.
c) RCU used in a hardwired configuration.
Plug one end of the remote cable in the connector on the bottom of
the RCU and the second side in the connector in the rear panel of the
BARCODATA 808s SP labelled 'REMOTE'.
4-2
All manuals and user guides at all-guides.com
RCU
Rear side of projector
T rrà v  † ‡hy y h‡v ‚ Ãv †‡ … ˆ p‡v ‚  †Ãi rs ‚ …rÃp‚   rp ‡ v t à ‡ ‚ à ‡ u rà † ˆ ƒ ƒ y ’ ÅU u v † q r ‰ v p r p ‚ € ƒ y v r †  v ‡ u Q h … ‡ ‚ s
W ‚ v …à y h Á‚ ‡ v prÃq  v †‡ hy y h ‡v ‚  à h ‰h  ‡Ã q r à …h pp‚ …q r…à hˆ à … p †r hˆ  P ƒ r … h ‡v ‚  v † † ˆ i w r p ‡ ‡ ‚
s‚ yy ‚  v t ‡  ‚ p ‚  q v‡ v ‚  † )   U u v † $
q r ‰ v p r € h ’  ‚ ‡ p h ˆ † r u h … € s ˆ y v ‡ r … ‡u rÃA 88 ÃÃS ˆ y r†
W   ‚ € à !   !"  à W '   à ƒ r … v ƒ u r … h y † 5 B 7 & R P S   +  6 \ Q F W T ’  p T  W D9 @ P P A A à Ãà  Ãà à P I W D 9 @ P P A A Ãà à  à à ÃP I t … r r à ) à ‚ ƒ r… h ‡ v ‚  sr …r  p r h  q !  ‡ u v† q r ‰ v p r € ˆ † ‡
P A A P I D  ‚ € & $ Ã6€ ƒ & $ à P u € & $ à P u € … r q Ã) à † ‡h  q i ’ h p p r ƒ ‡ h  ’ v  ‡ r …s r …r  p r …r p r v ‰ r q 
… r „ A $   %  ÃC “ C O M M . P O R T v p yˆ q v t v ‡r …s r …r  p r ‡ u h ‡€ h ’ p h ˆ † r
P O WE R / M A I NS PO RT 3 P OR T 4/ 5 P O RT 2 P O R T 1 P R O J E C T O R M O DE ˆ  q r † v… r q à ‚ ƒ r … h ‡v ‚  Å
45° 45°
) 
)  ) 
)  )
$ ' - (;,7
( 1 7 (5
3$86( 7 ( ; 7
3+$6 (

6 + $ 5 3 1
 
7 , 1 7


& 2/ 25
 
%5 , * +7 1
 
& 2 1 75
75(% / ( % $/$1 & (
% $ 6 6 9 2 /
ST!"!ÃDI ST!"!ÃPVU DS S@HPU@

Projector Address

a. Hardware set up of the projector address.
Every projector requires an individual address between 0 and 255
which is set with hardware DIP switches inside the projector. To
change that address, contact a BARCO authorized technician.
b. How to control the projector.
The projector's address may be set to any value between 0 and 255.
When the address is set, the projector can be controlled now with:
- the RCU for addresses between 1 and 9.
- computer, e.g. IBM PC (or compatible), Apple MAC, etc. for
addresses between 0 and 255.
Note : A projector will respond to a RCU set to an address of '0'
regardless of what address is set in the projector itself. Address "O"
is therefore a universal address.
c. Using your RCU.
Before using your RCU, it is necessary to enter the projector address
into the RCU (only when that address is between 1 and 9). The
projector with the corresponding address will listen to that specific
RCU.
When address 0, 'zero address' is programmed into the RCU, every
projector, without exception will listen to the commands given by this
RCU.

How to display a projector address?

Press the ADDRESS key (recessed key on the RCU) with a pencil.
The projector's address will be displayed in a 'Text box'. This text box
disappears after a few seconds.
To continue using your RCU, it is necessary to enter the same address
with the digit buttons (address between 0 and 9). For exemple, if the
Adrress Key displays projector address 003, then press the "3" digit
button on the RCU to set the RCU's address to match the projector's
address. Do not press digit 003. This will address the remote to '0'
and control all projectors in the room.
5976283 BARCOGRAPHICS 808s 160501
219
PROJECTOR
ADDRESS
001