Operation - RIKA Memo Gsm Operating Manual

7. OPERATION

Save your telephone-number (done only once)
The operation of the stove is controlled by SMS commands. These
consist of the reception code you selected (described earlier) and a
command. After correct installation of the GSM set you must save a
valid telephone number on the device. (This is not possible when you
suppress your telephone number.)
In this case the TEL command follows the reception code.
Example-SMS
The device will save the telephone
1234 TEL
number and send a confirmation
(Note the SPACE
message back (MOBILE NUMBER „your
between code and
number" OK).
command)
Now you are able to set the stove to another operating mode by using
SMS-commands.
Note
You are also able to save a new number by sending a TEL code
again.
You also can send commands without registering a telephone number
using simply the reception code. In this case you will get back a
message „Please save TEL. number" in your answer-SMS.
Caution:
If no telephone number is stored at the device you will not receive
any message in case of errors.
The simplest command is switching ON and OFF:
Example SMS:
Device ON with presetting (operating
1234 ON
mode and setting maintained from
previous operation, e.g. HEAT 35,
(Note the SPACE
AUTO)
between reception and
command code)
1234 OFF Device OFF
Commands - Control panel
Additional you also have the possibility to change the mode of
operating. If there is a room sensor installed, you can switch between
three different modes. (HEAT / ROOM / AUTO)
You simply write the command after the reception code and a space.
Example
Switch to HEAT, device ON (device setting
SMS:
maintained from previous operation e.g. 35%
1234 heat
heat output)
Example SMS: Switch to ROOM, device ON (Device setting
1234 room maintained from previous operation e.g. 25°C
room temperature)
Switch to AUTO device ON (device setting
Example SMS:
maintained from previous operation – drop
1234 auto
temperature, heating temperature, time frames)
In addition to changing the mode of operation you can also enter and
change the operation values of HEAT and ROOM per SMS. (Heat output
in % in HEAT mode and room temperature in C° in ROOM mode).
You write the required value behind the initial letters of the operating
mode (h for HEAT and r for ROOM).
Switch to selected operating mode (ROOM).
Example SMS
Device setting changed to the required setting
1234 r21
e.g. 21°C room set temperature.
Switch to selected operating mode (HEAT).
Example SMS:
Device setting changed to the required setting
1234 h65
e.g. 65% heat out-put.
In automatic mode the settings of the room temperature are not
possible. Changes must be carried out directly at the device.
SMS Replies - Control Panel
On activation of the SMS option each change of state is acknowledged
by an SMS reply. When you send a SMS message to your RIKA pellet
stove you must not suppress your telephone number. More detailed in-
structions for activation of sending the telephone number can be found
in the operating instructions of your mobile phone.
Successful switching on and mode switching by SMS is acknowledged
by a SMS confirmation.
Examples:
Operating
Confirmation SMS for a switched on device
mode:
Stove ON – HEAT 30 (value can vary according
HEAT Modus
to setting)
Stove ON – ROOM 25 (value can vary according
ROOM Modus
to setting)
AUTO Modus Stove ON – AUTO
If the device is switched off by SMS then a successful switch off is
acknowledged by a confirmation SMS message.
SMS message: Stove OFF is sent back.
If there is an error when a new command SMS is received, notification
of the error is sent back by SMS. You will receive notification of the
error on your mobile phone.
Examples:
Error
Error "NO PELLETS"
Error "FAN DEFECT"
Safety related error
"CALL SERVICE" - the GSM
function will be deactivated
If an error occurs in the
reception code.
If a wrong command was sent.
If an error occurs during operation, the respective error is sent by SMS
message to the number saved at the device.
Caution:
If no telephone number is stored at the device you will not receive
any message in case of errors.
Caution:
The error messages "STB" and "DOOR OPEN" will not be sent via
a message.
Text-message
FAILURE: no pellets
FAILURE: fan defect
FAILURE: call service – GSM off
FAILURE: code error
FAILURE: text error