Aux Output Programming; Selection Of Aux Output And Operating Mode - King gates ROLLS Instructions And Warnings For Installation And Use

Advanced programming
13.

AUX output programming

These programming sequences are not essential for system opera-
tion, but allow the AUX output to be activated by choosing the rele-
vant terminals.
The AUX output delivers 24Vdc
To interrupt the following programming sequences at any time, press
the SET and RADIO buttons simultaneously or wait 10 seconds.
AUX USED AS COURTESY LIGHT
If the AUX output is used as courtesy light to control the lamps, a
relay must be connected.
The light can be activated via a special transmitter button (to be pro-
grammed as indicated in the relevant paragraph)
SWITCHING ON/OFF OF THE LIGHT THROUGH A DEDICATED
TRANSMITTER BUTTON:
- connect a monostable relay;
- set the AUX output on the desired terminals;
- the work mode is only bistable, ON / OFF;
- program the desired transmitter button for the AUX output (see the
relevant paragraph)
The AUX output switches on/off whenever the programmed trans-
mitter is pressed.
13.1 - Selection of AUX output and
operating mode
Default setting = AUX disabled
This procedure allows activating the "AUX" output. By default, the
AUX output is bistable and is associated with the remote control key
memorized for this function.
To control the AUX output you need to register a radio
transmitter by following the procedure described in the rele-
vant paragraph and connect a suitable relay.
ACTION
STEP
PRESS THE START
1 BUTTON FOR 3
SECONDS
PRESS THE RADIO
2
BUTTON FOR 1 SECOND
If the "Sic" LED is
off, the AUX output
is deactivated. (if the
2.1a
setting is correct, go to
Point 4; if not, proceed
to Point 3a)
Setting the AUX output
on the Phototest
3a terminals (4 and 8)
PRESS THE SET BUTTON
FOR 1 SECOND
Setting the AUX output
on the Flash terminals (1
3b and 2)
PRESS THE SET BUTTON
AGAIN FOR 1 SECOND
(not required for standard installation)
RESULT
All the LEDs turn off (if
not, refer to Paragraph
14.1)
The "SIC" LED is
switched off
The "SIC" LED lights up
in red
or
The "SIC" LED lights up
in green
PRESS THE SET AND RADIO
BUTTONS SIMULTANEOUSLY OR
4
WAIT 10 SECONDS TO EXIT THE
PROCEDURE
STEP ACTION
PRESS START BUTTON
1
FOR 3 SECONDS
PRESS THE RADIO
2
BUTTON FOR 1 SECOND:
If the yellow "Set" LED is
on AUX = Electric lock
2.1a (if the setting is correct,
go to Point 4; if not, pro-
ceed to Point 3a)
Courtesy light setting
3a PRESS THE RADIO
BUTTON FOR 1 SECOND
If the red "Error" LED is
on in fixed mode
AUX = Courtesy light
2.1b
(if the setting is correct,
go to Point 4; if not, pro-
ceed to Point 3b)
Electric lock setting
3b PRESS THE RADIO
BUTTON FOR 1 SECOND
PRESS THE SET AND
RADIO BUTTONS
4 SIMULTANEOUSLY OR
WAIT 10 SECONDS TO
EXIT THE PROCEDURE
The LEDs return to
the normal operation
configuration
RESULT
All the LEDs turn off (if not,
consult Paragraph 14.1)
The red "radio" LED turns
on in the fixed mode
The red "radio" LED
remains lit in the fixed mode
and the red "Error" LED
lights up. The yellow "Set"
LED goes off.
or
The red "radio" LED turns
on in the fixed mode
The red "radio" LED
remains lit in the fixed mode
and the yellow "Set" LED
lights up. The red "Error"
LED goes off
The LEDs return to
the normal operation
configuration
49