Extron electronics Digital Video Scaler Series User Manual page 3

Table of Contents

Advertisement

im Vertrieb von
Installation
Step 1
Refer to the application example at the end of this
page. Turn off power to the scaler and the input
and output devices, and remove power cords from
them.
Step 2
Install the four rubber feet on the bottom of the
DVS 304 scaler, or mount the scaler in a rack.
Step 3
Attach input devices to the scaler.
Rear panel video inputs
SDI input (DVS 304 D or AD models only)
Attach an SDI source to this optional BNC.
Input 1: Composite video
Input 2: Composite/S-video/YUVi/YUVp
S-video (YC)
Composite Video
Y
B-Y
Y
/VID
/VID
/C
R-Y
R-Y
2
2
Input 3: S-video
3
Input 4: Composite/S-video/YUVi/YUVp/
RGBcvS/RGB scaled/RGB pass through
RGB/R-Y,Y,B-Y/YC/VID
4
Step 4
Attach output devices to the scaler.
Rear panel video outputs
Output BNC connectors
RGBHV
R
G
B
/R-Y
/Y
/B-Y
H/
V
HV
RGsB
R
G
B
/R-Y
/Y
/B-Y
H/
V
HV
www.camboard.de
CAMBOARD Electronics
Quick Start — DVS 304
SDI
1
VID
Component Video (Y, R-Y, B-Y)
B-Y
Y
B-Y
/C
/VID
/C
R-Y
2
YC
RGBS
B
R
G
/B-Y
/R-Y
/Y
H/
V
HV
Component Video (Y, R-Y, B-Y)
R
G
B
/R-Y
/Y
/B-Y
H/
V
HV
Tel. 07131 911201
Fax 07131 911203
Output 15-pin HD connector
You can connect both outputs simultaneously
to two different displays. The sync format is
the same for both outputs.
Step 5 (for DVS 304 A or
304 AD only)
Connect up to four balanced or unbalanced stereo
audio input devices to the DVS 304 as shown below.
Each audio input has a 3.5 mm, 5-pole captive screw
connector.
For detailed wiring instructions, see chapter 2
Installation and Operation.
Balanced and unbalanced
audio input
Tip
Sleeve
Tip
Sleeve
Unbalanced Input
(high impedance)
Balanced and unbalanced
audio output
Unbalanced Output
Tip
See Warning
Sleeve (s)
Tip
See Warning
Connect the sleeve to ground. Connecting
the sleeve to a negative (-) terminal will
damage the audio output.
Step 6
Plug the DVS 304, and the input and output devices
into a grounded AC source, then turn on the input
and output devices.
Step 7
Use the LCD menu screens (detailed on the
following pages) or RS-232 programming to
configure the scaler.
See chapter 2, Installation and Operation for more
detailed operating procedures, chapter 3, Serial
Communication for programming information, and
chapter 4, Ethernet Control for details on the default
Web pages.
ce-info@camboard.de
DVS 304 • Quick Start
RGB/R-Y,Y,B-Y
Tip
Ring
Sleeve (s)
Tip
Ring
Balanced Input
(high impedance)
Balanced Output
Tip
Ring
Sleeve (s)
Tip
Ring
QS-1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Digital Video Scaler Series and is the answer not in the manual?

This manual is also suitable for:

Dvs 304Dvs 304 dDvs 304 aDvs 304 ad

Table of Contents