Advertisement
Congratulations on the purchase of your new SecuRam SafeLogic Basic Safe Lock!
This Quick Start Guide will help you set up your new safe lock.
Important:
• Always perform operations with the safe lock system unlock and the safe door open.
• Before closing the door, make sure all the program changes are correct
• Duracell and Energizer Alkaline batteries recommended
Your Safe Lock comes with 2 pre-programmed entry codes:
• The Manager Code is set to 1-1-1-1-1-1
• The User Code is set to 1-2-3-4-5-6
Note: In many cases the safe manufacturer retains this manager code – see "About Manager Codes".
Step 1: Open Lock
• Enter the User Code (Default Code is 1-2-3-4-5-6)
• The Lock Opens. Its that easy!
Step 2: Changing your Code
• Enter "0" six times, you will hear 2 beeps
• Enter the existing code 1-2-3-4-5-6, you will hear 2 beeps
• Enter a new 6 digit code, you will hear 1 beep
• Re-enter the new 6 digit code, you will hear 1 beep
That's it! Your Code has been successfully changed.
You can now use your new code to open the lock.
You are ready to begin using your SecuRam safe lock.
For a full set of Operating Instructions, please visit our website at
About Manager Codes
• The default Manager Code is 1-1-1-1-1-1.
• This code is often retained by the safe manufacturer as a reset code. They retain this code in case you lose
your User Code.
Important: Check to see if the Default Manager Code is still active on your safe lock
– Enter the Default Manager Code 1-1-1-1-1-1
– If the safe lock opens, the Manager Code is still set at the default setting and must be
changed.
• Follow "Step 2: Change your Code" to change the Manager Code but this time enter the Manager Code of 1-
1-1-1-1-1, instead of 1-2-3-4-5-6.
• The Manager Code will be changed and can be used as a second access code.
• The Manager Code can also be used to enable, disable or delete the User Code. Instructions for these
functions can be found in the Operating instructions, available on our website at
S e c u R a m :
R e l i a b l e .
Quick Start Guide – SafeLogic Basic
I n n o v a t i v e .
www.securamsys.com
T r u s t e d .
www.securamsys.com
Advertisement
Table of Contents
Related Manuals for Securam SafeLogic Basic
Summary of Contents for Securam SafeLogic Basic
- Page 1 Quick Start Guide – SafeLogic Basic Congratulations on the purchase of your new SecuRam SafeLogic Basic Safe Lock! This Quick Start Guide will help you set up your new safe lock. Important: • Always perform operations with the safe lock system unlock and the safe door open.
- Page 2 How to Replace the Battery – SureLock Compartment Use these Battery Change instructions if your Entrypad is equipped with a removal battery compartment as detailed below. Step1: To replace the battery, locate the battery compartment. See Fig 1. Step 2: Release the latch of the battery compartment, by pulling lever downward.
- Page 3 How to Replace the Battery – Standard Compartment How to Replace the Battery – Standard Compartment Use these Battery Change instructions if your Entrypad has a concealed mounted battery compartment. Step1: To remove the EntryPad from the safe door, push up from the bottom of the EntryPad.
- Page 4 6 Digits Mechanical System Life Span: >10,000 Cycles (UL requirement) >100,000 Cycles (SecuRam design criteria) SecuRam Systems Inc. U.S.A. IMPORTANT: Warranty Information Your safe lock is eligible for a 12 month warranty covering product defects. Within 90 days of purchasing your safe/safe lock, please visit our website to register your product.
Need help?
Do you have a question about the SafeLogic Basic and is the answer not in the manual?
Questions and answers