1. Manuals
  2. Brands
  3. Securam Manuals
  4. Locks
  5. TD-2006-U100
  6. User manual

Securam TD-2006-U100 User Manual

Digital electronic lock
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Digital Electronic Lock
User's manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TD-2006-U100 and is the answer not in the manual?

Questions and answers

Related Manuals for Securam TD-2006-U100

Summary of Contents for Securam TD-2006-U100

  • Page 1 Digital Electronic Lock User’s manual...

  • Page 2: Keypad Arrangement

    TD-2006-U100 Digital Electronic Lock is specially designed for use in apartments and small offices. The lock operates via passwords (4 to10 digits) or in an emergency via an over-riding mechanical key. It has a stand-alone safety device and the special feature free- passage function for office use.

  • Page 3: Front Panel Diagram

    Front Panel Diagram : LED Display Screen : Digital Keypad : Front Panel : Cylinder Cover : Outside Lever Handle...

  • Page 4: Back Panel Diagram

    Back Panel Diagram : Decorative Cover : Battery Case : Function Switch : A/M Switch─Unused : Fastener of Battery Case’s Cover : Inside Lever Handle ⑦: Back Panel : Latch ⑧...

  • Page 5: Table Of Contents

    Contents Contents 1.How to enroll the administrator’s password...….7 2.Enroll an individual user’s password via an administrator ............11 3.Use an enrolled password to unlock …...14 4.Change an enrolled password .......16 5.Delete all enrolled passwords ......18 6.Delete a specific user’s enrolled password…….20 7.Withhold a specific user’s enrolled password ...23 8.Reset a specific user’s enrolled password which has been withheld........26...

  • Page 6: How To Enroll The Administrator's Password

    Password After completing the initial installation of TD- 2006-U100 Digital Electronic Lock according to its installation drawing sheet( Installation Instructions for TD-2006-U100 Lock) , move the Function Switch (located under battery cover) to the center position shown as Install batteries.
  • Page 7 then press the enter key Now the display screen shows meanwhile, the LED indicator’s green light blinks, with a “beep-beep” sound, and the lock is in the open status, with on the display screen. Press and the display screen shows two flashing letters .
  • Page 8 the factory-set default password. Press to confirm, and the display screen shows Input the same password again and press . Then, the display screen will show two red bars By now, this password has been enrolled as the Administrator’s one. The lock will open by turning the outside lever handle downwards.
  • Page 9 ◆ The default password 123456 will be deleted automatically after the operation mentioned as the above procedures 1.6 and 1.7. ◆ After the password has been set, please try to use it to unlock so as to make sure the password has been correctly enrolled.

  • Page 10: Enroll An Individual User's Password Via An Administrator

    2. Enroll An Individual User’s Password Via An Administrator The Function Switch is set to the center position Press any key on the keypad to wake up the lock, meanwhile the display screen will show two red bars Input the Administrator’s enrolled password, and press , then the display screen shows , meanwhile, the LED indicator’s green...
  • Page 11 Input a password (4 to 10 digits) selected by an individual user. Press and the display screen shows Input the same password again and press The display screen shows the ID number corresponding to this password. By now, this individual user’s password is enrolled. Note ◆...
  • Page 12 correctly enrolled. ◆ If a user needs to continuously enroll several passwords, the user can do like this: when the display screen shows ID No., press , then the display screen will show Then, the user needs only to follow the procedures 2.5 and 2.6.

  • Page 13: Use An Enrolled Password To Unlock

    3. Use An Enrolled Password To Unlock The Function Switch is set to the center position Press any key to wake-up the lock. The display screen shows . Simply input the correct enrolled password and press . Now the display screen shows the corresponding ID No., meanwhile, the LED indicator’s green light blinks, with a “beep- beep”...
  • Page 14 Note ◆ In case of inputting an enrolled password, if one has delayed to press any key for 10 seconds, this input will be cancelled and the lock will be in the awaiting mode. ◆ When a password has been enrolled, the display screen will show the ID No.

  • Page 15: Change An Enrolled Password

    4. Change An Enrolled Password The Function Switch is set to the center position Press any key on the keypad to wake up the lock, meanwhile the display screen will show two red bars Input the enrolled password to be changed, and press , then the display screen shows the ID No.
  • Page 16 press the keys until there appears on the screen.) Then, press and there will appear on t screen, so that the lock will be in the status of changing the passwords Input a new selected password (4 to10 digits) so as to change the former enrolled password.Press to confirm, and then the display screen shows...

  • Page 17: Delete All Enrolled Passwords

    5. Delete All Enrolled Passwords Move the Function Switch to the position Press any key on the keypad to wake up the lock, meanwhile the display screen will show two red bars Press , and the display screen shows two flashing letters Press , and the display screen shows the...
  • Page 18 Note ◆ The display screen will show if the deletion is unsuccessful. Try the above deletion again. If the deletion is still unsuccessful, the lock shall be sent back to the Seller’s factory for maintenance. ◆ The Administrator’s enrolled password will be again automatically reset to the default password 123456 corresponding to the ID No.

  • Page 19: Delete A Specific User's Enrolled Password

    6. Delete A Specific User’s Enrolled Password The Function Switch is set to the center position Press any key to wake-up the lock. The display screen shows . Input the Administrator’s enrolled password corresponding to ( Administrators’ ID Nos.) and press .The display screen shows the ID No.
  • Page 20 two flashing letters .Press the keys until there appears on the screen. Then, press and there will appear the ID No. or ID No. Press the keys to select the ID No. corresponding to the enrolled password to be deleted. Press the , this ID No.
  • Page 21 Note The enrolled password corresponding to or the enrolled password corresponding to be crosswise-deleted, but either of these passwords can’t delete itself.

  • Page 22: Withhold A Specific User's Enrolled Password

    7. Withhold A Specific User’s Enrolled Password The Function Switch is set to the center position Press any key to wake-up the lock, and the display screen shows Input the Administrator’s enrolled password corresponding ( Administrators’ ID Nos.) and press display screen shows...
  • Page 23 Press and the display screen shows two flashing letters .Press the keys until there appears on the screen. Then, press , and the display screen will show . Press the keys to select the ID No. corresponding to the enrolled password to be withheld ( except this ID No.).
  • Page 24 Note The specific user’s enrolled password is withheld after it has been withheld through its ID No. The user can’t open the lock by this withheld password. The user can operate with this password only after it has been reset. The enrolled password corresponding to ID or that corresponding to ID No.

  • Page 25: Reset A Specific User's Enrolled Password Which Has Been Withheld

    8. Reset A Specific User’s Enrolled Password Which Has Been Withheld The Function Switch is set to the center position Press any key to wake-up the lock, and the display screen shows Input the Administrator’s enrolled password corresponding (Administrators’ ID Nos) and press .The display screen shows the ID No.
  • Page 26 Press and the display screen shows two flashing letters . Press the keys until there appears on the screen. Then, press , and the display screen will show corresponding to the enrolled password which has been withheld. Press the , the specific user’s enrolled password which has been withheld and corresponding to this ID No.

  • Page 27: Use Two Selected Enrolled Passwords To Co-Operatively Unlock

    9. Use Two Selected Enrolled Passwords To Co-operatively Unlock The Function Switch is set to the center position Firstly, enroll at least two individual user’s passwords according procedures mentioned in Section 2. Enroll An Individual User’s Password Via An Administrator. Press any key to wake-up the lock.
  • Page 28 the indicator’s green light blinks, with a “beep -beep” sound, and the lock is in the open status. Press and the display screen shows two flashing letters . Press the keys until there appears on the screen. Then, press , and the display screen will show for one second.
  • Page 29 the ID No. corresponding to the other individual user’s enrolled password (except the ID No. or ID No. , that ). Press user’s enrolled password corresponding to that ID No. is confirmed as the enrolled password corresponding to Then, there will appear on the screen, which means it has been completed to set up the operation mode of using two selected enrolled passwords...
  • Page 30 procedures: 1) Press any key to wake-up the lock, and the display screen shows 2) Input the enrolled password corresponding to (One Cooperative User’s ID No.) and press . The display screen shows 3) Input the enrolled password corresponding to (the Other Cooperative User’s ID No.) and press .
  • Page 31 Note In the operation mode of using two selected Enrolled passwords to cooperatively unlock, the lock can be unlocked only via the enrolled password corresponding to and that corresponding to . When the ID No. corresponding to is deleted, the ID No. corresponding to will also be deleted.

  • Page 32: Set Up Free-Passage-Mode

    10. Set Up Free-Passage-Mode Unlock the lock by an enrolled password. 10.1 Press and hold until the screen 10.2 shows the ID No. corresponding to this password. There will occur a “beep-beep” sound. Then, loosen the user’s finger, and the display screen will show .

  • Page 33: Withhold Free-Passage-Mode

    11. Withhold Free-Passage-Mode In the awaiting status, with two red bars 11.1 shown on the display screen, press hold until there occurs 1 “beep-beep” sound. Then, loosen the user’s finger. The display screen will show . and then two red bars , which means that it has withheld the Free- Passage-Mode.

  • Page 34: Lock-Info Display

    12. Lock-Info Display 12.1 The Function Switch is set to the center position Press any key to wake-up the lock. 12.2 The display screen shows . Input the 12.3 Administrator’s enrolled password corresponding ( Administrators’ ID Nos.) and press . The display screen shows the ID No. corresponding to this password and meanwhile, the LED indicator’s green light blinks, with a “beep-beep”...
  • Page 35 Press and the display screen shows 12.4 two flashing letters . Press the keys until there appears on the screen. Then, press there will appear such lock info as ( which means the maximum number of enrolled passwords) and so on.

  • Page 36: Use The Override Mechanical Key To Unlock

    13. Use The Override Mechanical Key To Unlock In An Emergency In an emergency or in case that the electronic part of the lock fails to work normally, an override mechanical key can be used to unlock the door. 13.1 Insert the Cylinder-Cover removal tool so as to remove the oval cover.

  • Page 37: Basic Rules

    14. Basic Rules To press means to choose menu or to 14.1 cancel. 14.2 The enter key is used for confirming. A “beep- beep” sound is used for confirming a 14.3 program has been finished, e.g. the input of a password or the enrollment of a password has been finished).

  • Page 38: Form Of Error Info

    15. Form of Error Info Error Code Error Type Error of EEPROM in CPU: if it happened repeatedly, the lock needs maintenance Error deleting enrolled password: happened repeatedly, the lock needs maintenance No more passwords can be enrolled. Low voltage: batteries need to be replaced...

  • Page 39: Specifications

    SPECIFICATIONS: ➤Password Capacity : (TD-2006-U100) 99 passwords <0.1% ➤FRR <0.0001% ➤FAR ➤Password length : 4 to10 digits ➤Static Current: 15 µA (standard) ➤Power Supply: 4 AA-size alkaline batteries or 4 AA-size rechargeable batteries (1.2V, 1800mA.h) ➤Battery Life Span: At least 2 to 3 years (assuming the lock operates 10 times per day.)
  • Page 40 SecuRam Inc. U.S.A.

Table of Contents