Related Manuals for OLIMEX STM32-H107
Summary of Contents for OLIMEX STM32-H107
-
Page 1: Users Manual
STM32-H107 development board Users Manual All boards produced by Olimex are ROHS compliant Rev. A, December 2010 Copyright(c) 2010, OLIMEX Ltd, All rights reserved Page1... -
Page 2: Board Features
INTRODUCTION STM32-H107 header board provides easy way for developing and prototyping with STM32F107 connectivity line microcontroller, produced STMicroelectronics. STM32-H107 has JTAG port for programming and debugging, USB_OTG, user button, two status leds, and most of the GPIOs are on extension headers where you can connect your additional circuits. - Page 3 STM32-H107 board use ARM-based 32-bit microcontroller STM32F107VCT6 with these features: Core: ARM 32-bit Cortex™-M3 CPU – 72 MHz maximum frequency, 1.25 DMIPS/MHz (Dhrystone 2.1) – performance at 0 wait state memory access Single-cycle multiplication and hardware division – Memories –...
- Page 4 1 × 16-bit motor control PWM timer with dead-time generation and – emergency stop 2 × watchdog timers (Independent and Window) – SysTick timer: a 24-bit downcounter – 2 × 16-bit basic timers to drive the DAC – 14 communication interfaces –...
-
Page 5: Block Diagram
BLOCK DIAGRAM Page5... -
Page 6: Memory Map
MEMORY MAP Page6... - Page 7 6VAC 9VDC 330R/1% 3 3 0R/1 % 100nF 470uF/16VDC 47uF/6.3V/TANT EXT1-39 EXT2-39 EXT1-2 3 3 0R/1 % EXT2-38 EXT2-2 RESET CIRCUIT STATUS LEDS STM32-H107 3.3V Rev. Initial STAT2 390R/1% COPYRIGHT(C), 2009 390R/1% STAT1 http://www.olimex.com/dev NA(STM1001RWX6F) EXT1-3 RESET EXT2-3 330R/1% STAT1...
-
Page 8: Board Layout
BOARD LAYOUT Page8... -
Page 9: Reset Circuit
+5V_JTAG from JTAG – RESET CIRCUIT STM32-H107 reset circuit includes EXT1 pin 3, EXT2 pin 3, JTAG connector pin 15, STM32F107VCT6 pin 14 (NRST) and RESET button. CLOCK CIRCUIT Quartz crystal 25 MHz is connected to STM32F107 pin 12 (OSC_IN) and pin 13 (OSC_OUT). -
Page 10: Connector Descriptions
Default state is open. INPUT/OUTPUT Status LED1 (green) with name STAT1 connected to STM32F107VCT6 pin 63 (PC6/I2S2_MCK/TIM3_CH1). Status LED2 (yellow) with name STAT2 connected to STM32F107VCT6 pin 64 (PC7/I2S3_MCK/TIM3_CH2). Power-on LED (red) with name PWR – this led shows that +3.3V is applied to the board. - Page 11 PULL-DOWN PULL-DOWN +5V_JTAG PWR_JACK: Pin # Signal Name Power Input USB_OTG Pin # Signal Name +5V_OTG_PWR USB_OTG_D- USB_OTG_D+ OTG_ID 3V_BAT Pin # Signal Name VBAT Page11...
- Page 12 EXT1 Pin # Signal Name Pin # Signal Name 3.3V WKUP EXT1-5 EXT1-6 EXT1-7 EXT1-8 EXT1-9 EXT1-10 EXT1-11 EXT1-12 EXT1-13 USB_FAULT EXT1-15 EXT1-16 EXT1-17 EXT1-18 EXT1-19 EXT1-20 EXT1-21 EXT1-22 EXT1-23 EXT1-24 EXT1-25 EXT1-26 EXT1-27 EXT1-28 EXT1-29 EXT1-30 EXT1-31 EXT1-32 EXT1-33 EXT1-34 EXT1-35 VREF+...
- Page 13 EXT2 Pin # Signal Name Pin # Signal Name 3.3V EXT2-4 EXT2-5 EXT2-6 EXT2-7 EXT2-8 EXT2-9 EXT2-10 USB_VBUSON EXT2-12 EXT2-13 EXT2-14 EXT2-15 EXT2-16 EXT2-17 EXT2-18 EXT2-19 EXT2-20 EXT2-21 EXT2-22 EXT2-23 EXT2-24 EXT2-25 EXT2-26 EXT2-27 EXT2-28 EXT2-29 EXT2-20 EXT2-31 EXT2-32 EXT2-33 EXT2-34 EXT2-35 EXT2-36...
-
Page 14: Mechanical Dimensions
MECHANICAL DIMENSIONS Page14... -
Page 15: Available Demo Software
AVAILABLE DEMO SOFTWARE STM32F107_leds – STM32H107_usb_OTG – Page15... -
Page 16: Order Code
ORDER CODE STM32-H107 – assembled and tested (no kit, no soldering required) How to order? You can order to us directly or by any of our distributors. Check our web www.olimex.com/dev for more info. Revision history: REV. Initial - create November 2009 REV.A... - Page 17 This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such information or any incorrect use of the product.