Daikin Altherma 3 GEO Series Installer's Reference Manual page 69

# Code
[3.5] [0-00] Set weather-dependent heating:
[0-01] Note: There are 2 methods to set the
weather dependent curve. See
[0-02]
points
[0-03]
offset
require 4 field settings to be configured
according to the figure below.
T t
[0-01]
[0-00]
▪ T : Target leaving water temperature
t
(additional zone)
▪ T : Outdoor temperature
a
▪ [0-03]:
temperature. –40°C~+5°C
▪ [0-02]:
temperature. 10°C~25°C
▪ [0-01]:
temperature
temperature equals or drops below the
low
[9‑05]°C~[9‑06]°C
Note: This value should be higher
than
temperatures
required.
▪ [0-00]:
temperature
temperature equals or rises above the
high
[9‑05]~min(45, [9‑06])°C
Note: This value should be lower than
[0‑01]
temperatures less warm water is
required.
Cooling WD curve
Set weather-dependent cooling for the additional zone (if [3.4]=2):
EGSAH/X06+10DA9W(G)
Daikin Altherma 3 GEO
4P569820-1A – 2019.09
Description
"10.4.2 2-
curve" [ 4 61] and
"10.4.3 Slope-
curve" [ 4 61]. Both curve types
[0-03] [0-02]
Low outdoor ambient
High outdoor ambient
Desired leaving water
when the outdoor
ambient temperature.
[0‑00] as for low outdoor
warmer water
Desired leaving water
when the outdoor
ambient temperature.
as for high outdoor
# Code
[3.6] [0-04]
[0-05]
[0-06]
[0-07]
T a
is
Emitter type
For more info about this functionality, see
# Code
[3.7] [2‑0D]
The setting of the emitter type has an influence on the space heating
setpoint range and the target delta T in heating as follows:
Emitter type
Additional zone
0: Underfloor
heating
1: Fancoil unit
2: Radiator
Setpoint range
For more information about this setting, also see
zone" [ 4 64].
10 Configuration
Description
Set weather-dependent cooling:
Note: There are 2 methods to set the
weather dependent curve. See
curve" [ 4 61] and
points "10.4.3 Slope-
curve" [ 4 61]. Both curve types
offset
require 4 field settings to be configured
according to the figure below.
T t
[0-05]
[0-04]
[0-07] [0-06]
▪ T : Target leaving water temperature
t
(additional zone)
▪ T : Outdoor temperature
a
▪ [0-07]: Low outdoor
temperature. 10°C~25°C
▪ [0-06]: High outdoor
temperature. 25°C~43°C
▪ [0-05]: Desired leaving
temperature when the
temperature equals or drops below the
low ambient
[9‑07]°C~[9‑08]°C
Note: This value should be higher
than [0‑04] as for low
temperatures less cold
required.
▪ [0-04]: Desired leaving
temperature when the
temperature equals or rises above the
high ambient
[9‑07]°C~[9‑08]°C
Note: This value should be lower than
[0‑05] as for high
temperatures colder water is required.
"10.5.3 Main
Description
Emitter type
▪ 0: Underfloor heating
▪ 1: Fancoil unit
▪ 2: Radiator
Space heating Target delta T in
setpoint range heating [1‑0C]
[9‑05]~[9‑06]
Maximum 55°C Variable (see [3.B.1])
Maximum 65°C Variable (see [3.B.1])
Maximum 65°C Variable (see [3.B.1])
Installer reference guide
"10.4.2 2-
T a
ambient
ambient
water
outdoor
temperature.
outdoor
water is
water
outdoor
temperature.
outdoor
zone" [ 4 64].
"10.5.3 Main
69