Playing Or Recording From An Audio Cd - Korg D1600mkII Owner's Manual

Inserting a disc
Make sure that the power of the D1600mkII is turned on.
1. Open the disc tray
Press the eject button of the CD-R/RW drive, and the
disc tray will open.
2. Insert the disc
With the label of the disc facing upward, place it in
the disc tray.
3. Close the disc tray.
Press the eject button of the CD-R/RW drive to close
the disc tray.
Removing a disc
1. Press the eject button, and the disc tray will open.
2. Gently remove the disc from the disc tray.
3. Manually press the disc tray in until it is completely
closed.
Emergency removal of the disc
Normally you can use the above procedure to remove
and insert the disc. However if a problem (such as power
failure) occurs and the disc cannot be removed, you can
use the following method to remove the disc.
Please be aware that excessive use of this method
may cause the CD-R/RW drive to malfunction.
This procedure must be performed with the power
off.
To use this method, you will need a pin-like object of
less than 2 mm diameter, such as a straightened
paper clip.
Insert this "pin" straight into the manual eject
hole, and press.
The disc tray will be forced open.
3. Playing or recording from an
audio CD
To play an audio CD
1. Set the [PHONES LEVEL] knob and [MONITOR
OUT] knob to 0.
2. Press the eject button of the CD-R/RW drive to open
the disc tray, and insert the audio CD.
3. Access the [SONG/CD] "CDR/RW" tab page, and
press "CD Monitor" to set it to "
4. In the [SONG/CD] "CDR/RW" tab page, press
"
5. Gradually raise the [PHONES LEVEL] knob or the
[MONITOR OUT] knob.
6. To stop the audio CD, press the "
To record the sound of an audio CD
As an example, here's how to assign the L channel of an
audio CD to mixer channel 1, the R channel to mixer chan-
nel 2, and record the sound of the audio CD.
While recording the sound of an audio CD, you will
not be able to select digital input from the [S/P DIF
IN] jack.
1. Set the [CHANNEL 1] and [CHANNEL 2] faders to
0 dB.
If you want to hear the sound of the audio CD while
you record, we suggest that you first set the
[MASTER] fader below 0 dB, set the [PHONES
LEVEL] knob and [MONITOR OUT] knob to 0. Then
in step 8, gradually raise the volume while you play
back the audio CD, and when you have decided on
the volume, play back the CD once again and record
it.
The setting of the [MASTER] fader does not affect the
volume during recording.
2. Insert the audio CD into the CD-R/RW drive.
3. Access the [INPUT/TUNER] "Ch1–8" tab page, and
make sure that "DigiIn" is set to "
4. In the [INPUT/TUNER] "Ch1–8" tab page, select the
"Ch1" icon, and use the [VALUE] dial to select "CD-
L." Then select the "Ch2" icon and use the [VALUE]
dial to select "CD-R."
5. Access the [RECORD] "RecMode" tab page. For
"SelectRecMode," choose "Input."
6. Press the track 1 and 2 [TRACK STATUS] keys to
select REC (LED lit red).
7. Access the [SOLO/MONITOR] "Monitor" tab page,
and press "MasterLR" to set it to "
8. Access the [SONG/CD] "CDR/RW" tab page, and
press "
9. Press the [REC] key to enter record-ready mode, and
then press the [PLAY] key to start recording.
Playback of the CD in the CD-R/RW drive does
not synchronize with the beginning of recording
on the D1600mkII. If you want to start recording
from the beginning of the audio CD, use Trigger
Recording.
10. To stop recording, press the [STOP] key.
To stop playback of the audio CD before it ends, press
"
page.
When you finish recording, press the track 1 and
2 [TRACK STATUS] keys to set them to Play
(LED green), and play the song from the begin-
ning to verify that the recording occurred cor-
rectly.
."
".
".
."
" in the [SONG/CD] "CDR/RW"
".
."
161