Apache Labs ANAN-100/D Manual
  1. Manuals
  2. Brands
  3. Apache Labs Manuals
  4. Transceiver
  5. ANAN-100/D
  6. Manual

Apache Labs ANAN-100/D Manual

Ddc/duc transceiver
Hide thumbs
Table of Contents

Advertisement

Quick Links

Apache Labs ANAN-100/D
ANAN-100/D DDC/DUC Transceiver
This document uses the words Apache ANAN-10, ANAN-100 and ANAN-100/D
in reference to the Apache Labs Transceiver products
Apache Labs –
http://www.apache-labs.com
In cooperation with VK6APH and the Open Source Hardware and Software Project
http://openhpsdr.org
all images and manufacturer data is copied here with permission of the owner
Revision v1.8
April 23, 2013
1 of 70
authors N9VV and KC9XG

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ANAN-100/D and is the answer not in the manual?

Questions and answers

Related Manuals for Apache Labs ANAN-100/D

Summary of Contents for Apache Labs ANAN-100/D

  • Page 1 Apache Labs ANAN-100/D ANAN-100/D DDC/DUC Transceiver This document uses the words Apache ANAN-10, ANAN-100 and ANAN-100/D in reference to the Apache Labs Transceiver products Apache Labs – http://www.apache-labs.com In cooperation with VK6APH and the Open Source Hardware and Software Project http://openhpsdr.org...

  • Page 2: Table Of Contents

    Ethernet Connection...........................9 Connection to a dedicated Ethernet port is shown ................9 Ethernet switch is shown ........................9 Simple network setup..........................10 Here is what you need to get started with the ANAN-100/D..............11 ANAN-100/D Hardware Requirements....................11 13.8vdc minimum, 25A........................11 Dummy Load required for calibration....................11 PC microphone............................11...
  • Page 3 Apache Labs ANAN-100/D Antenna use and switching in ANAN-100/D...................27 HPF/LPF Filters and switching in ANAN-100/D..................29 OpenCollector BCD example by VK6APH.....................30 BCD (binary coded decimal) output....................30 Manual PA Calibration..........................31 Connect a suitable Dummy Load to ANT1..................31 Setup PA settings Band:........................32 Microphone Settings..........................33 Adjusting mic gain..........................33...
  • Page 4 Appendix – E Hermes block diagram (M0KHZ)..................52 Appendix – F Hermes functional diagram VK6APH................53 Contributing members to the Hermes project..................54 Kevin Wheatley M0KHZ ......................54 Abhi Arunoday Managing Director, Apache Labs.................54 Phil Harman - VK6APH.........................54 Bill Tracey - KD5TFD........................54 Lyle Johnson - KK7P........................54 Scotty Cowling - WA2DFI ......................54...
  • Page 5 Assigning an IP address using HPSDRProgrammer:..............57 ANAN-100/D block diagram........................58 ANAN-100/D PA and Filters........................59 ANAN-100D PA Filter PCB – installed in cabinet facing down.............60 ANAN-100/D Accessory Port (back panel).....................61 10Mhz Oscillator Jumpers........................65 Mic Jumpers.............................65 Angelia PCB - “Angelia” ANAN-100D....................66 APIPA - Automatic Private IP Addressing....................67 Additional reading:..........................68...

  • Page 6: Declarations Of Conformity

    <support@apach-labs.com> for details regarding your order or shipping charges. Apache Labs LLC, Inc. Declarations of Conformity The ANAN-100/D complies with FCC Part 97 rules for the Amateur Radio Service. It has been confirmed by the relevant authorities that the ANAN-10/100/100D DO NOT require FCC certification of any sort...

  • Page 7: Important Operation Tips

    4 rubber feet on bottom of case for proper cooling 2. Do not short rear speaker jack 3. Do not cover rear or bottom ventilation holes. Proper air circulation throughout the ANAN-100/D is necessary to prevent possible overheating and failure.

  • Page 8: Introduction

    PCB's (Mercury + Metis + Penelope). The Apache Labs ANAN equipment includes the Hermes design in a series of new transceivers. The ANAN-100/D provides a Gigabit (1000 baseT) Ethernet interface to the host PC. The ANAN-100/D does not use a Firewire™, or USB interface.

  • Page 9: Suitable Routers Or Lan Network Switches

    ANAN-100/D ANAN-100/D must be connected directly to a dedicated Ethernet port on the host PC or to a port on a suitable Ethernet router or switch. Connection to a dedicated Ethernet port is shown above 1000 baseT...

  • Page 10: Simple Network Setup

    Apache Labs ANAN-100/D Simple network setup The OpenHPSDR Hermes/Angelia, ANAN-10/ANAN-100/ANAN-100D radios are designed to work via Ethernet cabling on a "Local Area Network" or "LAN". Ethernet simplifies the installation, and configuration of hardware and software on a PC, making the installation basically plug and play. No sound card interface wiring, no Firewire cards or drivers, no USB ports or drivers needed.

  • Page 11: Here Is What You Need To Get Started With The Anan-100/D

    IC. Do NOT short these stereo pins or connect either side to ground! 6. DO NOT TURN THE ANAN-100/D RADIO ON until P*SDR software is properly installed and configured. ANAN-100/D Recommended Software requirements 1.

  • Page 12: Anan-100/D Front Panel

    Apache Labs ANAN-100/D ANAN-100/D Front Panel Power Ethernet Headphones Power Switch FPGA Activity Revision v1.8 April 23, 2013 12 of 70 authors N9VV and KC9XG...

  • Page 13: Anan-100/D Back Panel

    Apache Labs ANAN-100/D ANAN-100/D back panel 1. 13.8VDC Power connector 9. Transverter Rx 2. Balanced Speaker Out 10. Ext-1 3. Rx-2 11. Ground Lug 4. ANT-3 12. Transverter Tx 5 ANT-2 13. 10Mhz input 6. ANT-1 14. Push to Talk OUT 7.

  • Page 14: Quick Start Instructions

    The ANAN-100/D transceiver should be placed to allow unobstructed airflow around and beneath the housing. Damage can occur if the ventilation openings on the bottom or rear panel of the ANAN-100/D are blocked. Allow room for airflow between the housing and other equipment.
  • Page 15 Apache Labs ANAN-100/D S oftware Setup Go to the OpenHPSDR download page and download the P*SDR_mRX Installer software: ttp://openhpsdr.org/download.php scroll down to the WINDOWS section and look for the latest W5WC software example of OpenHPSDR Download webpage Revision v1.8 April 23, 2013...

  • Page 16: Windows

    Apache Labs ANAN-100/D Windows For example: On the OpenHPSDR Download webpage http://openhpsdr.org/download.php you will see: P*SDR mRx (compiled with MS VS 2010) the current version of P*SDR mRX 3.0.X.XX will have a current build number inserted in the place of “XX”. click on P*SDR mRX 3.0..XX and select “RUN” to install the application.
  • Page 17 Apache Labs ANAN-100/D Revision v1.8 April 23, 2013 17 of 70 authors N9VV and KC9XG...
  • Page 18 Apache Labs ANAN-100/D Revision v1.8 April 23, 2013 18 of 70 authors N9VV and KC9XG...
  • Page 19 Apache Labs ANAN-100/D Click on the desktop ICON to start P*SDR-mRX. If a P*SDR_mRX icon is not clearly apparent on your screen, use your start menu to locate the program. The program will begin with the “WISDOM” optimization. A one time DOS FFT optimization screen will appear. Wait for this process to finish and the DOS screen will disappear.
  • Page 20 This may take 10 minutes or more to complete the extended FFT calculation trough 262144. Wait for the message that it is OK. select “OK” to finish. Turn on your power supply. Push the POWER ON button on the ANAN-100/D. Then press the POWER button on P*SDR™.
  • Page 21 P*SDR/OpenHPSDR software has not been started Power button on the rig has not been activated Also check your LAN connector on the ANAN-100/D to insure that the Link Light on the LEFT side of the LAN connector is illuminated. Revision v1.8...
  • Page 22 Apache Labs ANAN-100/D Make a note of your ANAN-100/D Transceiver unique MAC address since this will be useful if there is a need for network problem-solving in the future. WARNING: Make sure you have selected the proper radio model from the selections on the LEFT side of the Hardware Configuration box.

  • Page 23: Hpsdrprogrammer V2 Utility

    An incorrect default value is 169.254.1XX.XXX. P*SDR™ will display the currently assigned IP address and MAC address of the ANAN-100/D Hermes board if the LAN connection is properly connected and configured. If the ANAN-100/D IP ADDRESS remains 0.0.0.0 then you must determine if P*SDR and your PC network connection is operating correctly.
  • Page 24 Apache Labs ANAN-100/D Please select a Sample Rate of 384khz, for the Panadapter display width, at this time (running P*SDR/OpenHPSDR 3.0.2.x) example 384khz panadapter single receiver display (entire 20M band) using the COLLAPSED display option Revision v1.8 April 23, 2013...
  • Page 25 Apache Labs ANAN-100/D The cluttered and dense entire Chicago AM Broadcast band shown using 3 x 384khz for RX1 General tab ---> APPEARANCE tab, and you should be able to change the graphical appearance of P*SDR by selecting different “skins”.

  • Page 26: Cw Key Selection And Wiring

    Apache Labs ANAN-100/D CW Key Selection and Wiring Select Iambic Paddles or straight key → To use a CW key with P*SDR™ you will need to enable it in the menu. To do so, click on Setup DSP tab followed by the Keyer tab.

  • Page 27: Antenna Use And Switching In Anan-100/D

    Apache Labs ANAN-100/D Antenna use and switching in ANAN-100/D There are many Antenna switching options for the Apache Labs ANAN-100/D. Below you see a screen picture of the Setup,General Ant/Filters, Antenna tab. The 1, 2, 3 selections correspond to the rear panel ANT1, ANT2, and ANT3 BNC connectors. You can select different antennas for receive and transmit on each band.
  • Page 28 Apache Labs ANAN-100/D Note the Antenna Control box on the right allows you to control the following options: 1. Software SWR Protection. Enabling this option will reduce power output when high SWR levels are detected. 2. Disable on Tune Pwr < 10W.

  • Page 29: Hpf/Lpf Filters And Switching In Anan-100/D

    HPF/LPF Filters and switching in ANAN-100/D The ANAN-100/D have a very effective set of High Pass Filters (HPF) and Low Pass Filters (LPF), available on the Setup, General, Ant/Filters/HPF/LPF tab. The HPF and LPF are automatically selected as you change bands, according to the settings on this form.

  • Page 30: Opencollector Bcd Example By Vk6Aph

    Apache Labs ANAN-100/D OpenCollector BCD example by VK6APH This is an example provided by Phil Harman VK6APH of how to code the P*SDR/OpenHPSDR Power_mRX program to give a BCD (binary coded decimal) output for control of external equipment (such as band information for a Linear Amplifier).

  • Page 31: Manual Pa Calibration

    7. Select the PA settings TAB on the Setup menu window. The PA Settings TAB allows you to set (calibrate) the ANAN-100/D Power Amplifier gain by band (dB – Power Output per Band) for each of the available Ham Bands. There is an up/down gain control for each band, which regulates the Power Amplifier output for that band.

  • Page 32: Setup Pa Settings Band

    Apache Labs ANAN-100/D Setup PA settings Band: 8. Select one of the bands on the PA settings TAB. 9. Ensure you have the Setup ---> Transmit tab ---> Tune control set to 100 and a 150W or larger Dummy Load connected to the selected antenna port on the ANT/FILTERS setup tab.

  • Page 33: Microphone Settings

    Adjusting mic gain . The ANAN-100/D microphone gain must be adjusted for each microphone used with the radio. The internal jumpers JP4, JP5, and JP6 on the Hermes board must be set properly for the type of microphone used. See the reference section of this document for the jumper settings, or refer to the document by Phil Harman VK6APH: http://svn.tapr.org/repos_sdr_hpsdr/trunk/Hermes/Documentation...
  • Page 34 Apache Labs ANAN-100/D (lower left), check "20db mic boost" and try again to adjust the "MIC" gain control on the main P*SDR window for 0 db on voice peaks. If you are still unable to achieve 0 db on voice peaks you can try increasing the Setup, Transmit tab "Mic Gain Max"...

  • Page 35: Transmit

    Apache Labs ANAN-100/D Transmit – Author Bill KC9XG The Setup, Transmit tab is used to set various transmit parameters. The "Profiles" drop down menu allows you select various transmit profiles. The default profile is "Default". You can modify profile settings on this tab and save them to a profile name you select, or you can just modify the included profiles to your liking.

  • Page 36: Tuning The P*Sdr Receiver

    Apache Labs ANAN-100/D Tuning the P*SDR receiver. Author Bill KC9XG Your ANAN-100/D is a "knobless" radio. Most functions are performed on a PC with the mouse or via keyboard commands. Preliminary receiver setup: 1. On the left side of the P*SDR window, locate the "AGC Gain" control and set the slider to 90. This control works similar to an RF gain control, but actually controls the level where the "Automatic Gain Control"...

  • Page 37: Attaching A Pc Microphone

    PC microphones to Hermes / ANAN-100/D. Garden variety PC microphones can give surprisingly good results when used with the P*SDR or external mic equalizers. Since I don't have a Hermes / ANAN-100/D+ I am unable to test these instructions with a working radio. Use at your own risk.

  • Page 38: P*Sdr Keyboard Commands

    Ring. Close Hermes / ANAN-100/D housing. 6. Connect radio to dummy load or suitable antenna. Power up radio. 7. Plug adapter into Hermes / ANAN-100/D+ Stereo mic plug. 8. Plug PTT switch into one side of RS 274-375. Revision v1.8...

  • Page 39: Modular Microphone Connections

    8 Pin Modular microphones available from Kenwood, Yaesu and others to Hermes / ANAN-100/D+. Since I don't have a Hermes / ANAN-100/D+ I am unable to test these instructions with a working radio. Use at your own risk.

  • Page 40: Example Adaptation

    1. Remove DC power from Hermes ANAN-100/D+. 2. Open Hermes / ANAN-100/D+ housing using a grounded wrist strap and an anti-static mat. Locate the following jumpers and change as needed: 3. JP4, Mic audio on Tip, jumper pins JP4-2 and JP4-3 (Hermes Default).

  • Page 41: Kenwood Modular

    The Hermes Jumpers JP4, JP5, and JP6 must be configured to accept the desired microphones: 1. Remove DC power from Hermes ANAN-100/D+. 2. Open Hermes / ANAN-100/D+ housing using a grounded wrist strap and an anti-static mat. Locate the following jumpers and change as needed: 3.
  • Page 42 Apache Labs ANAN-100/D IC-703 706MK1, 706MK2, 706Mk3, 2000, 2000h ICE-208, 2100H, 2725E, 2820, 7000,2800 Stereo Calrad terminal block. plug Ring : Pin 4 PTT See Hermes JP6 note! : Pin 5 Mic Ground Tip : Pin 6 Mic Hermes JP5 jumper between pins 2 and 3 for ICOM mics.

  • Page 43: Anan-100/D Rear Panel Connections

    ANAN-100/D Rear Panel connections Author William Diaz KC9XG ANAN-100/D Antenna connections as shown on 100W_Rev15A.pdf and as built on the back panel. 100W_Rev15A.pdf connector labels differ considerably from the ANAN-100/D back panel labels. 100W_Rev15A.pdf shows 2 separate RX2 in connectors, but they are, in fact, different as indicated by the underline.
  • Page 44 Apache Labs ANAN-100/D EXT1, EXT2 or XVTR RX. The receive signal path is then Ant(n), LPF, Bypass, external filter or pre-amp, Ext(n) or Xvrt RX, HPF, To_RX, then to Hermes/Angelia RX1_in. EXT1, EXT2, or XVTR RX can be used with an external receive antenna, but TX/RX switching/attenuation must be provided to protect the receiver from excessive receive levels which could damage the receiver.

  • Page 45: Troubleshooting Section

    Troubleshooting symptom ANAN-100/D receiver deafness: Improper/unintended settings: 1. Your ANAN-100/D receive signal path is routed to the bypass connector when EXT1, EXT2, or XVTR is selected on the Setup, Ant/Filters tab. 2. A pre-amp, or filter must be connected between the bypass connector and...

  • Page 46: Troubleshooting Symptom, No Transmit Audio

    Apache Labs ANAN-100/D Troubleshooting symptom, no transmit audio. 1. Mic is disabled by default when VAC1 is enabled. A. Setup, audio tab has check boxes for enabling PTT etc, while VAC is active. B. Alternately, disable VAC when transmitting with the mic.

  • Page 47: Apache Labs International Support

    Apache Labs ANAN-100/D Apache Labs International Support Technical support for ANAN-100/D from the factory is available via the Apache Labs Yahoo Group http://groups.yahoo.com/group/apache-labs/ <support@apache-labs.com> or directly via email Apache-Labs-Support U.S.A. Apache Labs is pleased to offer telephone support. In the United States you may contact the Telephone Customer Support Technician in five ways: (1) Skype ID "Apache-Labs"...

  • Page 48: Appendix - A - Computer Performance

    Apache Labs ANAN-100/D APPENDIX - A – Computer performance Computer Performance Processing of streaming data in real-time can be a challenging task for Windows-based applications and device drivers. This is because by design Windows is not a real-time operating system. There is no guarantee that tasks can be executed in a deterministic (timely) manner.

  • Page 49: Appendix - B - Warranty

    "Terms of Use". IMPORTANT The FPGA and other components on the ANAN-100/D PCBs can be damaged by Electrostatic Discharge (ESD). When handling the PCB, you should take ESD precautions (e.g. use a work bench with an antistatic mat on it and wear a grounded wrist strap).

  • Page 50: Appendix - C - Openhpsdr Software

    Apache Labs ANAN-100/D APPENDIX - C – OpenHPSDR Software OpenHPSDR P*SDR(tm) modifications W5WC source code: click here http://svn.tapr.org/repos_sdr_hpsdr/trunk/W5WC KD5TFD source code: click here http://svn.tapr.org/repos_sdr_windows/P*SDR/branches/kd5tfd W5WC skins with installer here http://svn.tapr.org/repos_sdr_hpsdr/trunk/W5WC/OpenHPSDR_Skins/ A BIG thank you to Joe, K5SO and Doug, W5WC for adding support for the 100W PA and other refinements to the code! K.I.S.S_Konsole from OpenHPSDR team...

  • Page 51: Appendix - D -- Vk6Aph Ddc/Duc Presentation

    Apache Labs ANAN-100/D Appendix – D -- VK6APH DDC/DUC Presentation HIGHLY RECOMMENDED FOR ALL NEW DDC LEARNERS To learn all about Digital Down Converter technology, please purchase DVD #6 from (Amateur Radio Video News) in which Phil Harman VK6APH teaches us the practical details from his wonderful presentation at ARRL/TAPR DCC-2008.

  • Page 52: Appendix - E Hermes Block Diagram (M0Khz)

    Apache Labs ANAN-100/D Appendix – E Hermes block diagram (M0KHZ) Revision v1.8 April 23, 2013 52 of 70 authors N9VV and KC9XG...

  • Page 53: Appendix - F Hermes Functional Diagram Vk6Aph

    Apache Labs ANAN-100/D Appendix – F Hermes functional diagram VK6APH Revision v1.8 April 23, 2013 53 of 70 authors N9VV and KC9XG...

  • Page 54: Contributing Members To The Hermes Project

    THANK YOU each for the wonderful gift you have shared with us all Kevin Wheatley M0KHZ who conceived the Hermes and is the Project Lead Abhi Arunoday Managing Director, Apache Labs, PCB layout, manufacturer Phil Harman - VK6APH - Software & hardware development, especially the brain wave for maintaining full DAC bits while reducing power.

  • Page 55: Appendix - G The Cordic Algorithm

    Apache Labs ANAN-100/D Appendix – G The CORDIC Algorithm The CORDIC mathematical algorithm used in the Apache-100W Transceiver; CORDIC - Wikipedia, the free encyclopedia http://en.wikipedia.org/wiki/CORDIC CORDIC FAQ http://www.dspguru.com/dsp/faqs/cordic CORDIC FAQ-II http://www.dspguru.com/info/faqs/cordic2.htm CORDIC for Dummies http://www.jacques-laporte.org/cordic_for_dummies.htm The CORDIC Algorithm http://www.andraka.com/cordic.htm CORDIC http://www.nist.gov/dads/HTML/cordic.html...

  • Page 56: Appendix - H - Hpsdrprogrammer

    Apache Labs ANAN-100/D Appendix – H – HPSDRProgrammer Author 2013 William Diaz KC9XG Updated 03/07/2013 OpenHpSDR/ Hermes/ANAN-* SDR: Updating firmware and assigning a static IP address. The OpenHPSDR HPSDRProgrammer_V2 application provided by KV0S can be used to load new firmware and assign or change IP address with properly configured OpenHpSDR Hermes/ANAN-* radios.

  • Page 57: Upgrading Openhpsdr Firmware Using Hpsdrprogrammer

    Apache Labs ANAN-100/D B. If your Hermes/ANAN-* MAC and IP address are not shown as indicated above, your OpenHpSDR Hermes/ANAN-* cannot be found on your network. Please check your Ethernet connections and try again. Upgrading OpenHPSdr firmware using HPSDRProgrammer: 1. Download new firmware by visiting http://openhpsdr.org/download.php . Find the appropriate .rbf firmware file for your SDR.

  • Page 58: Anan-100/D Block Diagram

    Apache Labs ANAN-100/D ANAN-100/D block diagram Revision v1.8 April 23, 2013 58 of 70 authors N9VV and KC9XG...

  • Page 59: Anan-100/D Pa And Filters

    Apache Labs ANAN-100/D ANAN-100/D PA and Filters Revision v1.8 April 23, 2013 59 of 70 authors N9VV and KC9XG...

  • Page 60: Anan-100D Pa Filter Pcb - Installed In Cabinet Facing Down

    Apache Labs ANAN-100/D ANAN-100D PA Filter PCB – installed in cabinet facing down Revision v1.8 April 23, 2013 60 of 70 authors N9VV and KC9XG...

  • Page 61: Anan-100/D Accessory Port (Back Panel)

    Apache Labs ANAN-100/D ANAN-100/D Accessory Port (back panel) The Hermes/Angelia schematic detail J16 pin numbering does not correspond to keyed IDC ribbon cable numbering conventions. An IDC to DB25 adapter cable further re-arranges the pin numbers. Pin number Number in parentheses is the J16 pin...
  • Page 62 Apache Labs ANAN-100/D The Hermes/Angelia schematic detail J16 pin numbering does not correspond to keyed IDC ribbon cable numbering conventions. An IDC to DB25 adapter cable further re-arranges the pin numbers. Pin out and connections between 26 pin J16, Modified (shifted) 26 pin IDC ribbon cable and DB 25.
  • Page 63 Apache Labs ANAN-100/D P*SDR Hermes/Angelia ANAN CTRL Tab Accessory I/O (female) Port Schematic J-16 as shown DB25 cable 17 OC0 18 0C1 19 OC2 20 OC3 21 OC4 22 OC5 23 OC6 14 OC REF 24 OC REF Revision v1.8...
  • Page 64 Apache Labs ANAN-100/D ANAN-10 Hermes DDC DUC Transceiver PCB NOTE: Please refer to the excellent Hermes jumper documentation written by Phil Harman VK6APH that can be found on the OpenHPSDR Documentation website: http://svn.tapr.org/repos_sdr_hpsdr/trunk/Hermes/Documentation Revision v1.8 April 23, 2013 64 of 70...

  • Page 65: 10Mhz Oscillator Jumpers

    Apache Labs ANAN-100/D 10Mhz Oscillator Jumpers J20: When a jumper is inserted between pins 1 and 3 (the default setting) the internal 10 MHz reference oscillator is selected. When pins 2 and 4 are jumpered, an external 10 MHz reference is selected at J25.

  • Page 66: Angelia Pcb - "Angelia" Anan-100D

    Apache Labs ANAN-100/D Angelia PCB - “Angelia” ANAN-100D J24 J22 Revision v1.8 April 23, 2013 66 of 70 authors N9VV and KC9XG...

  • Page 67: Apipa - Automatic Private Ip Addressing

    Apache Labs ANAN-100/D APIPA - Automatic Private IP Addressing Definition: A feature of Microsoft Windows, APIPA is a DHCP failover mechanism for local networks. With APIPA, DHCP clients can obtain IP addresses when DHCP servers are non-functional. APIPA exists in all modern versions of Windows except Windows NT.

  • Page 68: Additional Reading

    Apache Labs ANAN-100/D Additional reading: Please refer to this webpage for the most recent documentation by Phil Harman VK6APH for the OpenHPSDR version of the Hermes http://svn.tapr.org/repos_sdr_hpsdr/trunk/Hermes/Documentation http://www.n9vv.com Software Links: • http://openhpsdr.org/wiki/index.php?title=HPSDRwiki:Community_Portal • http://openhpsdr.org/download.php • http://svn.tapr.org/listing.php?repname=OpenHPSDR+KISS • http://svn.tapr.org/listing.php?repname=OpenHPSDR+Windows • http://svn.tapr.org/listing.php?repname=OpenHPSDR+Main •...
  • Page 69 Apache Labs ANAN-100/D 1023 Tower B4, Spaze I-Tech Park Sector - 49, Sohna Road Gurgaon - 122001 Haryana, India Tel: 91-0124-4245173/4/5 (10AM - 6PM IST) Email: support@apache-labs.com Website: www.apache-labs.com Revision v1.8 April 23, 2013 69 of 70 authors N9VV and KC9XG...
  • Page 70 Apache Labs ANAN-100/D NOTES __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ Revision v1.8 April 23, 2013 70 of 70...

Table of Contents

Save PDF