Huawei ECC800 User Manual

Huawei ECC800 User Manual

Data center controller
Hide thumbs Also See for ECC800:
Table of Contents

Advertisement

ECC800 Data Center Controller
V100R002C10
User Manual
Issue
05
Date
2019-09-16
HUAWEI TECHNOLOGIES CO., LTD.

Advertisement

Table of Contents
loading

Summary of Contents for Huawei ECC800

  • Page 1 ECC800 Data Center Controller V100R002C10 User Manual Issue Date 2019-09-16 HUAWEI TECHNOLOGIES CO., LTD.
  • Page 2 Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS"...
  • Page 3: About This Document

    About This Document About This Document Purpose This document describes the ECC800 data center controller in terms of features, devices, user interfaces (UIs), and power-on commissioning, as well as frequently asked questions (FAQ) and troubleshooting measures. This document describes all the functions of the ECC800. Certain functions are implemented by hardware such as the UPS and PDU, and may be unavailable if the hardware is not connected to the ECC800.
  • Page 4 Added the description about how to connect the HT-500 dehumidifier.  Deleted Wireless Components.  Deleted Facial Recognition. Issue 02 (2019-06-06)  Added Facial Recognition.  Added Wireless Components. Issue 01 (2018-07-02) This issue is the first official release. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 5: Table Of Contents

    3.2.7 Smoke Detector................................45 3.2.8 Temperature Sensor ................................. 46 3.2.9 Alarm Beacon................................... 46 3.2.10 (Optional) Smart U Space Manager ..........................47 3.2.11 eLight Actuator ................................48 3.2.12 Water Sensor .................................. 50 Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 6 6.2.3.2 Commissioning IPC6325 Camera (SD Card Configured) ..................113 6.2.4 Commissioning a Camera (LAN Switch Networking Scenario) ................115 6.2.4.1 Commissioning IPC6325 Cameras..........................115 6.2.4.2 Commissioning IPC6325 Camera (SD Card Configured) ..................118 Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 7 6.9.1 NetEco Management ..............................157 6.9.1.1 Connecting the Communications Cable ........................157 6.9.1.2 Setting NetEco Parameters............................157 6.9.1.3 Creating an ECC800 on the NetEco ..........................158 6.9.1.4 Setting the Transparent Transmission Function......................159 6.9.2 Third-party NMS Management (over SNMP) ......................162 6.9.2.1 Connecting the Communications Cable ........................162 6.9.2.2 Setting SNMP Management Parameters ........................162...
  • Page 8 8.1.8.26 How to Set and Add the Multi-functional Sensor?....................212 8.1.8.27 How to Set and Add the Smoke Detector (Connected to the AI/DI Port on the ECC800)? ........214 8.1.8.28 How to Set and Add the Smoke Detector (Connected to the AI/DI Port on the Skylight Actuator)? ....216 Issue 05 (2019-09-16) Copyright ©...
  • Page 9 8.1.22 How Can I Handle DO Association Failure? ......................236 8.1.23 What Do I Do If the ECC800 WebUI Display Language Changes from Chinese to English During Use? ..236 8.1.24 What Do I Do If the ECC800 Fails to Communicate with the UPS5000-E? ............236 8.1.25 What Do I Do If a Message Indicating Unauthorized Fingerprint Is Displayed During Fingerprint Scanning on...
  • Page 10 ECC800 Data Center Controller User Manual Contents 8.1.39 How Should I Modify Device Names over the ECC800 WebUI ................251 8.2 APP Operations .................................252 8.2.1 How to Connect to a WiFi Network ..........................252 8.2.2 How to Prepare and Login App ............................252 8.2.3 How Do I Ensure that Device Positions in the Plan View Are Consistent with Actual Positions? ......254...
  • Page 11: Safety Precautions

    The "NOTICE", "WARNING", and "DANGER" statements in this document do not cover all the safety instructions. They are only supplements to the safety instructions. Huawei will not be liable for any consequence caused by the violation of general safety requirements or design, production, and usage safety standards.
  • Page 12  Keep irrelevant people away from the equipment. Only operators are allowed to access the equipment.  Use insulated tools or tools with insulated handles, as shown in the following figure. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 13  To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telecommunication network voltage (TNV) circuits. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 14: Personnel Requirements

    Do not power on the equipment before it is installed or confirmed by professionals. 1.2 Personnel Requirements  Personnel who plan to install or maintain Huawei equipment must receive thorough training, understand all necessary safety precautions, and be able to correctly perform all operations.
  • Page 15 When selecting, connecting, and routing cables, follow local safety regulations and rules. The static electricity generated by human bodies may damage the electrostatic-sensitive components on boards, for example, the large-scale integrated (LSI) circuits. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 16: Installation Environment Requirements

     Ensure that the equipment room provides good heat insulation, and the walls and floor are dampproof.  Install a rat guard at the door of the equipment room. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 17: Mechanical Safety

    Before hoisting objects, ensure that hoisting tools are firmly secured onto a load-bearing object or wall.  Ensure that the angle formed by two hoisting cables is no more than 90 degrees, as shown in the following figure. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 18 Ensure that the wider end of the ladder is at the bottom, or protective measures have been taken at the bottom to prevent the ladder from sliding. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 19 Metal shavings from drilling may short-circuit boards inside the equipment.  Obtain the consent from the customer, subcontractor, and Huawei before drilling.  Wear goggles and protective gloves when drilling holes. ...
  • Page 20 Choose railways, sea, or a road with good condition for transportation to ensure equipment safety. Avoid tilt or jolt during transportation.  Move a cabinet with caution. Any bumping or falling may damage the equipment. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 21: Overview

    Overview 2.1 Positioning The ECC800 is the core component for the smart module local management. It is intelligent, flexible in connection, easy to maintain, and reliable. It adopts the POE bus for expansion, and allows all intelligent monitoring devices to be flexibly laid out so that it can manage the devices in the smart module.
  • Page 22 Supports local WiFi hotspots. After you install the WiFi module at the USB port on the ECC800, you can connect to the ECC800 using the app on the mobile phone or tablet computer to view the basic information about the smart module, such as layout, resources, energy efficiency, environment, and alarms.
  • Page 23: Device Description

    User Manual 3 Device Description Device Description 3.1 ECC800 The ECC800 consists of power supply units (PSUs) and an ECC800 main control module and monitors the equipment and environment in the smart module. Figure 3-1 ECC800 (front view) (1) PSU 1...
  • Page 24 3 Device Description Figure 3-2 ECC800 (rear view) (1) 53.5V DC_OUT1 (2) 53.5V DC_OUT2 (3) AC_INPUT1 (4) AC_INPUT2 Figure 3-3 ECC800 main control module (side view) (1) SIM card slot (2) Micro-SD card slot ECC800 Specifications Table 3-1 ECC800 environmental specifications Item Specifications –20°...
  • Page 25 ECC800 Data Center Controller User Manual 3 Device Description Table 3-2 ECC800 structural specifications Item Specifications Dimensions (L x W x H) 442 mm x 330 mm x 43.6 mm Color Black Installation Can be installed in a 1 U space in a standard...
  • Page 26  After installing the WiFi module, connect the WiFi module to the ECC800 using the app on the mobile phone or tablet computer to view the basic information about the smart module, such as layout, resources, energy efficiency, environment, and alarms.
  • Page 27 3 Device Description Indica Color Name Status Description NetEco successfully. Blinking at The ECC800 does not register short with the NetEco (the indicator intervals blinks at 4 Hz, on for 0.125s and then off for 0.125s). Alarm Steady on A system failure alarm is indicator generated.
  • Page 28 In non-wireless network (802.15.4) The RF_Z indicator network RF_Z pairing mode, press and hold down is blinking at super (802.15.4) the button for 1.2s to 5s to enter the short intervals. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 29 Then the IP addresses for the ECC800 WAN_1 and WAN_2 ports will restore to the default addresses. Communications Ports The ECC800 provides the following communications ports. Figure 3-4 shows the pins of the RJ45 port. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 30 There are four RS485 ports (COM1/12V–COM4/12V). Table 3-9 provides the RS485 port pin definitions. Table 3-9 RS485 port pin definitions Item Description Pin sequence Pin 1 RS485+ Pin 2 RS485– Pin 3 12 V DC_OUT Pin 4 RS485+ Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 31 Steady on: The 12 V DC output is normal.  Off: No 12 V DC output is provided. There are two DO dry contact outputs (DO_1 and DO_2). Table 3-11 provides the DO port pin definitions. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 32 Pin 3 Pin 4 Power Ports The ECC800 provides four power ports, including two AC input ports (AC_INPUT1 and AC_INPUT2) and two DC output ports (DC_OUTPUT1 and DC_OUTPUT2). Table 3-13 provides the power port pin definitions. Table 3-13 Power port pin definitions...
  • Page 33: Southbound Device Introduction

    Among the four RS485 ports, two support 12 V DC, 400 mA power expansion output.  The other two are isolated, with the default communications rate of 9600 bit/s, and do not support power output. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 34: Smart Eth Gateway

    3.2.2 Smart ETH Gateway A smart ETH gateway allows the extension of the 53.5 V DC power supply and FE communication for the ECC800 and can be flexibly deployed in a smart module. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 35 If you press the BLINK button, the RUN indicator blinks intermittently at button super short intervals (blinking at super short intervals for 0.5s and then off for 0.5s) for 5 seconds. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 36: Access Control System

    Blinking at The smart ETH gateway long successfully registers with intervals the ECC800 and the software runs properly (the indicator blinks at 0.5 Hz, on for 1s and then off for 1s). Blinking at The smart ETH gateway does...
  • Page 37: Access Actuator

    The access actuator is the control component for the aisle door in a smart module. It connects to the ECC800 controller over FE port, wireless networking (802.15.4). It opens the magnetic lock by detecting the card swiping information of the card reader, door open button information, and fire linkage information.
  • Page 38 POE input: One POE port that complies with IEEE802.3at. POE port FE communication, 10/100M communications rate Wireless One wireless communication port that complies with IEEE802.15.4, communicatio mutual backup with FE communication Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 39 ECC800 and the software runs properly (the indicator blinks at 0.5 Hz, on for 1s and then off for 1s).  Blinking at short intervals: The Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 40 0.05s and then off for 0.05s).  Blinking intermittently at super short intervals: The access actuator is searching for a network (the indicator blinks at super short intervals for 0.5s and then Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 41: Fingerprint And Card Reader With A Keypad

    For details, see "Access control device operating status." (1) Fingerprint reader (2) LED indicator Table 3-22 Specifications for the fingerprint and card reader with a keypad Item Specifications Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 42 Card swiping LED indicator The indicator blinks The indicator blinks blue, red, and blue blue, red, and blue in order. in order. Buzzer sounds The buzzer sounds The buzzer sounds once. once. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 43: Fingerprint And Card Reader

    The indicator is off. steady green. Unauthorized LED indicator The indicator blinks The indicator blinks fingerprint blue, red, blue, red, blue, red, blue, red, collection and blue in order. and blue in order. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 44: Card Reader With A Keypad

    Figure 3-10 Card reader with a keypad Table 3-26 Specifications of a card reader with a keypad Item Specifications Dimensions (L x W x H) 114 mm x 63 mm x 25 mm Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 45: Magnetic Lock

    (card swiping, key pressing) 150mA, minimum input current 12 V DC/300 mA Communications mode Wiegand communications port 3.2.3.1.5 Magnetic Lock Figure 3-11 Double door magnetic lock Figure 3-12 Single door magnetic lock Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 46: Cabinet Access Control System

    The system displays the status of cabinet doors and locks in real time, the system displays the status of cabinet doors and locks in real time and reports the unauthorized door opening.  The system supports remote unlocking. Figure 3-14 Electronic cabinet lock Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 47: Ac Actuator

    The AC actuator is used in a smart module to control the lighting inside the smart module by receiving commands from the access control system or host, infrared linkage information (disabled by default), or signals from the light button. It also provides a charging port for the pad. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 48 One route of dual RS485 ports, not isolated (reserved). AI/DI detection Two AI/DI dry contacts, connecting to two light buttons.  BLINK button Press the button for less than 1 second to start blinking. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 49 Blinking at The AC actuator successfully long intervals registers with the ECC800 and the software runs properly (the indicator blinks at 0.5 Hz, on for 1s and then off for 1s). Blinking at The communication is...
  • Page 50: Skylight Actuator

    (5) BLINK button (6) Status indicator (7) Address DIP (8) COM1 port switch (9) COM2 port (10) POE port (11) 48 V power port Specifications Table 3-30 Skylight actuator technical specifications Item Specifications Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 51 Blinking at The skylight actuator long intervals successfully registers with the ECC800 and the software runs properly (the indicator blinks at 0.5 Hz, on for 1s and then off for 1s). Blinking at The communication fails or the...
  • Page 52 The skylight actuator provides one DO port (LOCK/GND) and one DI port (BUTTON/GND). Table 3-32 lists the LOCK/GND/BUTTON/GND port pin definitions. Table 3-32 LOCK/GND/BUTTON/GND port pin definitions Item Description LOCK/GND LOCK 12V_OUT pin sequence BUTTON/GN BUTTON D pin sequence Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 53: Multi-Functional Sensor

    3.2.6 Multi-Functional Sensor A multi-functional sensor integrates the temperature and humidity (T/H) sensor, smoke sensor and infrared detection. The multi-functional sensor can connect to the ECC800 over FE or wireless communication. The infrared detection function is enabled only when the intelligent lighting function is enabled.
  • Page 54 Blinking at The multi-functional sensor running status long successfully registers with indicator intervals the ECC800 and the software runs properly (the indicator blinks at 0.5 Hz, on for 1s and then off for 1s). Blinking at The multi-functional sensor short...
  • Page 55: Smoke Detector

    Figure 3-19 Smoke detector Table 3-35 Technical specifications of a smoke detector Item Specifications Operating voltage DC12V (9–16 V DC) Quiescent current < 8 mA Alarm current < 35 mA Output mode Relay output Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 56: Temperature Sensor

    3.2.9 Alarm Beacon When a fire occurs or smokes are generated in the micro-modular equipment room, the alarm beacon generates an audible signal and flashes to inform operators of fire and security risks. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 57: Optional) Smart U Space Manager

    The smart U space manager is designed for IT asset management of the data center. The system automatically detects the physical location of IT devices in the data center, collects IT asset codes and the information about U space usage. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 58: Elight Actuator

    ≤ 0.2 kg (main control box), ≤ 0.35 kg (asset detection Weight strip) Installation mode Magnet-based installation 3.2.11 eLight Actuator The eLight actuator has the function of associating alarms, access authorization status, and atmospheres. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 59 The smart module raises a critical alarm. Blinking for Access authorization fails and the aisle door cannot be 3 seconds opened. Blinking The eLight fails to communicate with the ECC800. Orange light Steady on The smart module raises a major alarm. Yellow light Steady on The smart module raises a minor alarm.
  • Page 60: Water Sensor

    The WLDS600 water sensor with the BOM number of 33010556 consists of a water detection cable, a water detector, an extension line, and a conversion cable. Figure 3-24 WLDS600 water sensor (1) Tie line (2) Water leakage location cable (3) End cap Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 61: Wlds900 Water Sensor

    DIN track install supported. 3.2.12.2 WLDS900 Water Sensor The WLDS900 water sensor with the BOM number of 33010352 consists of a water detection cable, a water detector, and a conversion cable. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 62: Electrode Water Sensor

    –40° C to +85° C Storage temperature Humidity 10%–80% RH (non-condensing) 3.2.12.3 Electrode Water Sensor The electrode water sensor with the BOM number of 33010444 contains electrode probes and cables. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 63: Wifi Module

    The WiFi module provides WiFi signals for equipment such as pads and mobile phones to interact with the host computer. Figure 3-27 WiFi module Table 3-45 Technical specifications Item Specifications Wireless standard IEEE 802.11n, IEEE 802.11g, and IEEE 802.11b Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 64: Eth Converter

    5%–90% RH (non-condensing) Power < 0.8 W 3.2.14 ETH Converter The ETH converter is used to convert the Modbus–RTU protocol or CAN protocol to the Modbus-MAC protocol for connecting to the POE bus. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 65 (blinking at super short intervals for 0.5s and then off for 0.5s) for 10 seconds. E-label Supported Indicators Table 3-47 ETH converter indicators Indicator Color Name Status Description Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 66: Pad

    1s). Blinking at The communication fails or short the ETH converter fails to intervals register with the ECC800 (the indicator blinks at 4 Hz, on for 0.125s and then off for 0.125s). Blinking The indicator blinks at super short intervals for 0.5s...
  • Page 67 Video recording: rear camera up to 1080 pixels at 30 FPS; front camera up to 720 pixels at 30 FPS  Zoom mode: digital zoom  Photo resolution: rear camera up to 8 M (3264 x 2448 Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 68: T/H Sensor

    Power adapter charge time: about 3.5 hours (5 V 2A adapter) 3.2.16 T/H Sensor 3.2.16.1 T/H sensor (BOM number: 33010346) Figure 3-30 Appearance The T/H sensor uses an RJ45 connector. Figure 3-31 Pins of an RJ45 connector Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 69: T/H Sensor (Bom Number: 02310Nbs)

    9–16 V DC Storage temperature -40° C to 80° C (non-condensing) Output RS485 3.2.16.2 T/H Sensor (BOM number: 02310NBS) Figure 3-32 Appearance (1) Status indicator (2) RS485_IN (3) RS485_OUT (4) Address DIP switch Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 70 –20° C to +70° C Temperature measuring range Temperature accuracy ± 1° C –10° C to +55° C Operating temperature Operating voltage 9–16 V DC –40° C to +70° C Storage temperature Output RS485 Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 71: T/H Sensor (Bom Number: 02311Fqg)

    < 180 mW – 40° C to +70° C Storage environment Weight About 85 g 3.2.17 Intelligent Battery Monitoring System The intelligent battery monitoring system consists of the iBOX (CIM) and iBAT (BIM). Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 72: Ibox

    ETH gateway. (Optional) When a battery system needs to be managed by multiple iBOXs, the iBOXs can be connected to northbound devices using straight-through cables (the ECC800 supports four iBOXs in parallel through the smart ETH gateway) without cascading.
  • Page 73 (7) RF_Z antenna port (8) BCB_1–BCB_4 ports (9) BCB_OUT and BCB_IN (BCB_2–BCB_4 reserved) ports (10) Networking switch (11) PWR indicator (12) RUN indicator (13) ALM indicator (14) RF_Z indicator (15) Delivered antenna Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 74 Figure 3-38 Power port pins Table 3-55 12 V, 2 A port pin definitions Definition Description – In this scenario, an external power module is adopted to supply 12 V DC operating voltage. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 75 Table 3-57 POE port pin definitions Definition Description Supports power supply through the POE port. The TX– terminal is an RJ45 terminal with an indicator. 4, 5 P45_P1 RX– 7, 8 P78_P1 Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 76 Signal Status Initial Remarks Descriptio Descriptio Status  Dry contact Open: Open Dry contact input signal The dry input and – contact output signal input is open.  Closed: The dry Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 77 If the battery string is not configured with the neutral wire, measure the current of either the positive or negative battery string cable. The following uses the scenario where the battery string is configured with the neutral wire as an example. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 78 OFF.  Controls 0 V: There battery circuit is no driving breaker trip signal for and outputs 12 V driving tripping. signals  12 V: There is a driving Secondary side Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 79 12 no driving V driving signals signal for Secondary side ground tripping.  12 V: There is a driving signal for tripping. DIP Switch Table 3-63 DIP switch description Definition Description Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 80 (No communicati legitimate on cable is northbound data loose. has been received for 3 minutes.)  If yes, reconnect communi cation cable.  If no, go to the next step. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 81 Press the button for less iBOX blinking function than 1s. Button pressing Press and hold the button Creates a network if no network has for more than 1s but less been created. Switches between network Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 82: Ibat

     Supports the hibernation function. (When it detects that the battery voltage is low, it will enter the low-power mode.)  Communicates with the iBOX wirelessly. iBAT Appearance Figure 3-43 iBAT2.0 Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 83 The iBAT is blinking. (iBattery 2.0) Blinking at short intervals (iBattery 3.0)  If an indicator blinks at long intervals, it is blinking on for 1s and then off for 1s. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 84 Initializes the network parameters if there is a network. Button holding Hold down the button Clears the current network and resets the down for more than 5 wireless module; disconnects the network. seconds. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 85: Ui Description

    ECC800 Data Center Controller User Manual 4 UI Description UI Description 4.1 WebUI For data transmission security, the ECC800 supports WebUI access through TLS. Figure 4-1 Home page WebUI Introduction Table 4-1 WebUI introduction Second-Leve Third-Level Function Factor Remarks l Menu...
  • Page 86 AI/DI device Integrated PDU, parameters. PDU8000, and Power Distribution Unit Aisle Connected devices, such as Multi-Functiona l Sensor Group, Access Actuator Group, and Skylight Actuator Group – Cooling Connected Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 87 FusionModule by default. Setti System type is FusionModule2000 by default. NOTE If System type is General, the ECC800 is a general collector that collects device data and reports the data to the northbound NMS. Monitor IP Set the IP address ...
  • Page 88 Set basic alarm Parameters Parameters parameters and alarm association Alarm Linkage parameters. Performance Performance Query and set device Parameters Parameters performance parameters. All Configured View all the preset Data performance parameters Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 89 Fault Export fault Information information. Download the app Obtaining installation package by scanning the QR code.  Parameter Synchronize Sync device parameters to Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 90  a: The factory settings can be restored only on the WebUI.  b: Multi-Module Monitoring is displayed on the Home page only after you set Smart Module Cascading. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 91: Mobile Phone App

    Details system devices and other devices. iFind Allows you to modify the names and positions of devices in the device layout diagram, and deliver a blinking command to a device under Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 92 Data files, and historical data. Import Allows you to import a configuration file. Data Network Paramet Paramet er Sync Version Check the Software Version and Hardware Version of the device. Info Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 93: Pad App

    Allows you to modify the names and positions of devices in the device layout diagram, and deliver a blinking command to a device under iFind. Operation Access Event Performa Allows you to view device performance data, such as the battery curve Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 94 Data files, and historical data. Import Allows you to import a configuration file. Data Network Paramete Paramete r Sync Version Check the Software Version and Hardware Version of the device. Info Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 95: Power-On Commissioning

    You have obtained the ECC800 IP address as well as the user name and password used for WebUI login.  A PC with an IP address in the same network segment as the ECC800 IP address is prepared, and the PC has connected to the WAN_1 port on the ECC800. Context After installing or replacing the device or ECC800, set monitoring parameters and add the device.
  • Page 96 If the ECC800 connects to a LAN and a proxy server has been selected, perform Step 3.3 Step 3.4. If the ECC800 connects to the Internet, and the PC in a LAN accesses the Internet over a proxy  server, do not perform Step 3.3 Step 3.4.
  • Page 97 WebUI. Choose Tools > Compatibility View, and add the web access address to the compatibility view. Add the ECC800 IP address to the list of trusted sites. Figure 5-2 Adding an address Enable file download and set the security level of the trusted site to low.
  • Page 98 5 Power-On Commissioning Figure 5-3 Setting parameters When switching between different versions of the ECC800 on your PC, you are advised to clear the historical Internet Explorer cache. Failing to do so may cause some information missed or exception after login. The following provides the details: 1.
  • Page 99: Commissioning Configuration Wizard

    Procedure Step 1 Log in to the ECC800 WebUI as an administrator. The configuration wizard is displayed when you log in to the ECC800 WebUI for the first time or the system type is switched. Step 2 Choose Maintenance > Configuration Wizard to access the parameter configuring page for the deployment wizard.
  • Page 100: Commissioning Event Notification

    To implement alarm notification by email, the following conditions must be met:  The ECC800 is connected to a network with an email server through a WAN port. Both the Internet and local area network (LAN) are supported. The ECC800 supports only SMS notification service but not data service by using the 3G module.
  • Page 101 Password for cursor and 139 Mail smtp.139.com Non-encryption: 163 Mail, 126 press Enter to Mail, and QQ obtain email Mail. Hotmail smtp-mail.out TLS encryption: server IP look.com addresses. 189 Mail smtp.189.com Non-encryption: Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 102 Step 3 Add an email address to receive emails. The email address is used only for configuring the email function and is not used for other purposes. The address is encrypted during transmission in the ECC800 to ensure that the personal data of users is fully protected.
  • Page 103 The mobile phone number is used only for configuring the SMS function and is not used for other purposes. The phone number is encrypted during transmission in the ECC800 to ensure that the personal data of users is fully protected.
  • Page 104: Commissioning The New Main Way

    In the new main way scenario, general input units and power distribution units communicate with the ECC800 using the Modbus-MAC protocol. After the general input units and power distribution units properly connect to the ECC800, the ECC800 automatically identifies the units.
  • Page 105 Path: Maintenance > Parameter Sync Step 2 Set parameters for power distribution units on the ECC800 WebUI. (Optional) To modify the branch signal name of the power distribution unit, choose System Settings > Signal Name Modify and access the Batch Signal Configuration to modify the name, and then tap Submit.
  • Page 106: Commissioning The Elight

    Toggle switches 1 to 4 of the DIP switch specify the device address in binary mode. ON indicates 1, and OFF indicates 0. Table 5-5 Setting a device address Address Toggle Toggle Toggle Toggle Switch 1 Switch 2 Switch 3 Switch 4 Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 107 Step 3 Set eLight parameters. Log in to the ECC800 WebUI as an administrator. In the Smart Module View, click Modify Device. Select an eLight actuator under Devices, drag it to the access actuator to which you want to bind the eLight actuator, and click Exit Edit Mode.
  • Page 108  Warning: white light None The eLight strip light is steady blue (atmosphere light). NOTE After you set the alarm severity, the eLight indicator is off if no alarm is generated. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 109: Feature Description

    In this example, the door status sensor is connected to the AI/DI_1 port on the independent deployment AI_DI 1. Log in to the ECC800 WebUI as an administrator. Choose System Settings > Signal Name Modify. The Batch Signal Configuration page is displayed.
  • Page 110: Commissioning A Door Status Sensor (Connected To The Ai/Di Port On The Rack Environment Unit)

    2. Set AI/DI_2 sensor type to Door sensor, click Submit. Settings (AI/DI_2) Step 2 Check the door status sensor functions. Table 6-3 Commissioning the sensor Check Method Normal Connection Status Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 111: Commissioning An Access Control Device And A Cabinet Electronic Lock

     A maximum of eight access actuators are supported.  When the fingerprint reader is connected to the ECC800 for the first time, the permissions need to be synchronized. Procedure Step 1 Set the access user management and access permission management.
  • Page 112 ID, press * on the keyboard of the access controller to stop the authentication process. Then, enter user ID*password#. To query the user ID, log in to the ECC800 WebUI as an administrator. Choose System Settings > Access Management. In the Authorization area, view the user ID corresponding to the user name.
  • Page 113  If the access control system uses a Card and password reader, choose Monitoring > Aisle > Access Actuator Group > Access Actuator n on the ECC800 WebUI, click Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 114 Choose Query > Access Event on the WebUI, you can view the type of this access control event. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 115: Commissioning The Exit Button, Skylight Button, Atmosphere Light, Emergency Button, And Magnetic Lock

    Follow-up Procedure Status Attempt to open the door by The aisle door is You need to restore the pressing the emergency button opened successfully. emergency button. when the aisle door is closed. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 116: Commissioning An Emergency Door Release Button

    ----End 6.2 Video Management 6.2.1 Preparing Documentation Before commissioning a camera, prepare the following documents in addition to this document. Table 6-13 Documentation for Commissioning Preparation Component Document Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 117: Networking Scenarios

    To ensure the normal operating of the ECC800, avoid high data traffic, such as the concurrent display of dynamic monitoring of cameras and VCN500 video playback.  To ensure the normal operating of the ECC800, you can view the videos from a maximum of two IPC6325-WD-VR cameras concurrently. LAN Switch Networking Scenario There are multiple VCNs for multiple smart modules, you are advised to evenly distribute the cameras to each VCN.
  • Page 118: Commissioning A Camera (Smart Eth Gateway Networking Scenario)

    Context  The existing network is equipped with the ECC800 that supports the Dynamic Host Configuration Protocol (DHCP). After the ECC800 and IPC6325 camera are powered on, the IPC6325 camera automatically obtains an IP address that is in the same network segment as the ECC800 IP address.
  • Page 119 Use the following IP address and set an IP address to the planned IP address for the camera. The IP address should be in the range of 192.168.248.50 to 192.168.248.199. Step 3 On the ECC800 WebUI, click Add under Video Information. In the New Video Information dialog box that is displayed, enter camera/VCN information.
  • Page 120 ONVIF interface of the IP camera is changed, enter the new password in Password. Otherwise, the ECC cannot collect motion detection alarms from the IP camera. Figure 6-8 Adding video information Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 121 (Optional) If you use the SD card when no VCN is configured, perform commissioning by following the instructions in 6.2.3.2 Commissioning IPC6325 Camera (SD Card Configured). Set camera stream type, primary stream, and secondary stream 1 parameters. Set coding protocol to H.265. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 122 ECC800 Data Center Controller User Manual 6 Feature Description Figure 6-10 Setting primary stream parameters Figure 6-11 Setting secondary stream 1 parameters Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 123: Commissioning Ipc6325 Camera (Sd Card Configured)

    Context If the VCN is not configured and an SD card is chosen, perform the following procedure. Procedure Step 1 Log in to the Huawei IPC WebUI. Step 2 Format the SD card. Choose Settings>System Configuration>Storage Management. The Storage Management page is displayed. Format the SD card.
  • Page 124 720P 0.8M Step 4 Select Enable, click Add, add motion detection areas, set motion detection parameters, and click Save. Figure 6-13 Setting motion detection parameters Step 5 Set the deployment policy. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 125: Commissioning A Camera (Lan Switch Networking Scenario)

    6.2.4.1 Commissioning IPC6325 Cameras Prerequisites If multiple cameras are accessed, retain the connection of one camera and disconnect connections from other cameras. After commissioning the connected camera, commission other cameras in the same way. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 126 Choose Settings > Video/Audio/Image > Video Settings, and set IP address, Subnet mask, and Gateway IP address for the camera according to the site plan. Set coding protocol to H.265. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 127 ECC800 Data Center Controller User Manual 6 Feature Description Figure 6-16 Setting primary stream parameters Figure 6-17 Setting secondary stream 1 parameters Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 128: Commissioning Ipc6325 Camera (Sd Card Configured)

    Set IPv4 address, IPv4 subnet mask, and IPv4 gateway address to the planned values. Figure 6-18 Basic camera configuration Format the SD card. Choose Settings> System Configuration > Storage Management. The Storage Management page is displayed, format the SD card. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 129 Result Coding Resolution Frame rate I-frame Minimum Supported protocol interval required video bit rate storage duration H.265 1080P H.264 1080P H.265 720P 0.8M H.264 720P H.265 720P 0.6M H.264 720P 0.8M Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 130 Select Enable, click Add, add motion detection areas, set motion detection parameters, and click Save. Figure 6-20 Setting motion detection parameters Set the deployment policy. Figure 6-21 Setting the deployment policy Set the alarm linkage policy. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 131: Setting Parameters On The Vcn Webui

    VCN540 is https://192.168.2.101:8443) in the address bar of the Internet Explorer and press the Enter button. The OMU Portal supports Internet Explorer 8.0 and later versions. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 132 After the first login, change the password in time to ensure account security and prevent unauthorized network attacks, such as data tampering. Huawei will not be liable for any security issues caused by your failure to change the default password in time or password loss after changing.
  • Page 133: Setting Parameters On The Vcn Ivs Client

    VCN IP address in the address box of the Internet browser, and log in to the OMU Portal system.  (Optional) Deploying IVS in Stack Mode. For details, log in to the http://e.huawei.com/, search for the VCN product documentation, open the documentation, and see the section (Optional) Deploying IVS in Stack Mode.
  • Page 134 After the first login, change the password in time to ensure account security and prevent unauthorized network attacks, such as data tampering. Huawei will not be liable for any security issues caused by your failure to change the default password in time or password loss after changing.
  • Page 135 In the Assign Device View Rights area, select the cameras to be browsed and queried by the user. Set other parameters based on the documentation delivered with the equipment or the documentation obtained by referring to the Preparing Documentation section, and click Finish. ----End Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 136: Linkage Control

    You have obtained the IP address of the ECC800 as well as the user name and password used for WebUI login.  A PC with an IP address in the same network segment as that of the ECC800 is prepared, and the PC has connected to port WAN_1 on the ECC800. ...
  • Page 137: Fire Control Linkage

    6 Feature Description 6.3.1 Fire Control Linkage Context  The ECC800 can generate an alarm using the multi-functional sensor or smoke sensor in the aisle. This alarm, however, cannot be used to trigger the customer's fire extinguishing system.  A passive dry contact alarm signal of the customer's fire extinguishing system can be...
  • Page 138 Choose System Settings > Signal Name Modify. The Batch Signal Configuration page is displayed. Set Device type to ECC800 and Device name to ECC800, and click OK. On the query result tab page, set the new signal name of AI/DI_6 to Fire and click Submit.
  • Page 139: High Temperature Linkage

    The ECC800 implements high temperature linkage. If it detects high temperature alarms by interacting with multi-functional sensors and all smart cooling products fail to communicate with the ECC800, the ECC800 opens skylights based on the alarm status to facilitate heat dissipation.
  • Page 140 That is, the RF_Z indicators on the ECC800 and AC actuator are both steady green.  If the RF_Z indicator on the ECC800 is not steady green, hold down the SW button on the ECC800 for more than 6 seconds to make the ECC800 enter non-networking status. ...
  • Page 141 Select the actual camera type and go to the camera web page. For details, see the section about camera commissioning. Choose Settings> Network > Platform Connection > Second Protocol Parameters. On the ONVIF and GENETEC tab pages, set platform interconnection parameters. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 142 Select Enable, click Add, add motion detection areas, set motion detection parameters, and click Save. Figure 6-29 Setting motion detection parameters If there are multiple cameras, repeat Step8.a Step 8.3. ----End Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 143: Pue Configuration

    IT load output NOTE When the configuration mode is set to Standard, the ECC800 can automatically calculate the PUE of multiple devices connected in the N+1 and 2N scenarios. 6.4.1 Configuring PUE Standard Mode Procedure Step 1 Log in to the ECC800 WebUI as an administrator.
  • Page 144 User Manual 6 Feature Description Step 5 View the PUE. Choose Query > Performance Data and set Device to ECC800 from the drop-down list box. For other searching criteria such as Performance data, Statistics mode, Start time, and End time, select the item based on requirements and click Query. You can also view the PUE in the dashboard or curve on the home page.
  • Page 145: Configuring Pue User-Defined Mode

    Deletes a parameter setting for the total power consumption or IT power consumption. Procedure Step 1 Log in to the ECC800 WebUI as an administrator. Step 2 Choose System Settings > PUE Configuration. Step 3 Ensure that PUE function is set to Enable.
  • Page 146: Viewing Pue Data

    IT load output) Performance data source: The ECC800 obtains total electricity energy of branches from the power distribution devices. Step 6 You can also view the PUE in the dashboard or PUE Chart on the home page.
  • Page 147: Battery Management

    If iBOXs and iBATs are configured, perform the following steps to commission them. 6.5.1 Setting iBOX and iBAT Parameters Procedure Step 1 Log in to the ECC800 WebUI as an administrator. Step 2 Choose Monitoring > Power Distribution > iBOX/CIM > Running Parameters. Issue 05 (2019-09-16)
  • Page 148: Networking Iboxs And Ibats In Wireless Mode

    Blinking at long intervals: The indicator is on for 1 second and then off for 1 second alternately. − Blinking at super short intervals: The indicator is on for 0.05 seconds and then off for 0.05 seconds alternately. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 149 Number. Check that iBAT Number is set to a correct value and that the iBAT is successfully networked. Step 5 (Optional) If multiple iBOXs are cascaded, repeat Step 1 Step 4 to perform networking for remaining iBOXs and iBATs. ----End Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 150: Asset Management

    Connect the smart U space manager to the COM1 or COM2 port on the rack environment unit. Procedure Step 1 Log in to the ECC800 WebUI as an administrator. Step 2 View the position of the smart U space manager. Choose Monitoring > Cabinet > IT Cabinet > Smart U Space Manager.
  • Page 151: Querying The U Space Use Information

    ----End 6.6.2 Querying the U Space Use Information Prerequisites  The ECC800 is connected to the NMS that supports asset management.  The actual assets of the smart module have been allocated. Procedure Step 1 Log in to the ECC800 WebUI as an administrator.
  • Page 152 6 Feature Description Context IT cabinets, network cabinets, and smart cooling products support power management. The ECC800 connected to an IT cabinet is used as an example in this section. Procedure Step 1 Log in to the ECC800 WebUI as an administrator.
  • Page 153 2QF1(L1), the branches for subsequent cabinets are 1QF2(L2), 2QF2(L2), and the like.  If the branch for the first cabinet is 1QF10(L1), 2QF10(L1), the branches for subsequent cabinets are 1QF9(L3), 2QF9(L3), and the like. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 154 The alarm hysteresis is 5% by default. That is, if the cabinet load factor overhigh alarm threshold is 90%, the raised alarm will be cleared when the load factor drops to a value smaller than 85%. ----End Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 155: Setting Fault Isolation Parameters

     Smart rPDU overcurrent disconnection: Whenever the ECC800 detects overcurrent of an rPDU branch, it disconnects the rPDU of this branch to protect the IT devices. Then the rPDU branch fault information is displayed in the power supply and distribution link diagram.
  • Page 156: Viewing The Power Supply Links Diagram

    6.7.4 Viewing the Power Supply Links Diagram Procedure Step 1 Connect the pad to the WiFi network of the ECC800 in the room. Step 2 Log in to the ECC800 app as the administrator. Step 3 View the power supply status of the smart module and basic information about each device in real time to quickly locate faults.
  • Page 157 (tap to view the basic information about the smart rPDU)  Yellow: smart rPDU (Click to view the rPDU number, current, and status)  Blue or green: non-smart rPDU Branch switch SPD switch Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 158: Cooling Capacity Management

    The number of smart cooling products (number of started smart cooling products) with the valid maximum cooling capacity received by the ECC800 is greater than or equal to the Number of running air conditioners in this group in Teamwork settings of smart cooling products.
  • Page 159: Viewing Cooling Capacity Usage Information

    Smart cooling products have been connected to the ECC800. Procedure Step 1 Connect the PAD to the WiFi network of the corresponding ECC800 in the room. Step 2 Choose Home > Temp.. The view displays the temperature distribution map of each cabinet.
  • Page 160: Optional) Setting Cooling Management Parameters

    The smart module is configured with an integrated UPS or integrated PDF. Electricity has been configured for IT cabinets, network cabinets, and smart cooling products. The ECC800 collects statistics on IT branch power information, which is mapped to IT cabinets and network cabinets.
  • Page 161 Monitoring > Cooling > NetCol5000 > Running Info > Status Information.  When iCooling is enabled, the T/H threshold can only be set on the ECC800 WebUI.  When iCooling is disabled, smart cooling products enter the intelligent teamwork control mode (teamwork control of smart cooling products).
  • Page 162: Viewing The Cooling Links Diagram

    Submit. Figure 6-44 Setting running parameters Step 3 Use the pad to connect to the WiFi network of the ECC800 in the room. Step 4 Log in to the ECC800 app as the administrator. Step 5 View the cooling distribution information.
  • Page 163 Table 6-28 Specifications of the links for a single smart cooling product Item Specifications Smart cooling product appearance Alarm (tap to view specific alarms) Internal fan Condensate pipe (yellow: high temperature) Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 164: Setting The Temperature Map

     A maximum of eight T/H sensors can be cascaded to each COM port. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 165  The first group of T/H sensors (sensors 1 to 8) are connected to the COM1 port on the ECC800, the second group to the COM2 port, the third group to the COM3 port, and the fourth group to the COM4 port.
  • Page 166 Number of connected devices list. − If the T/H sensor does not connect to the ECC800 properly, check whether the cable between the T/H sensor and the ECC800 is connected properly, whether the T/H sensor and ECC800 are running properly, and whether the input parameters are consistent with the T/H sensor parameters.
  • Page 167: Remote Management

    When the smart module can be connected to the NetEco, perform the following steps to configure parameters. Procedure Step 1 Apply for a fixed IP address to the equipment room network administrator. Step 2 Set the IP address, subnet mask, and default gateway on the ECC800 WebUI. Table 6-31 IP parameters Path Parameter...
  • Page 168: Creating An Ecc800 On The Neteco

    ECC800 Data Center Controller User Manual 6 Feature Description Step 4 Set NetEco communications parameters on the ECC800 WebUI. Table 6-32 NetEco parameters Path Parameter Default Setting Value System Server IP 192.168.8.1 IP address of the primary NetEco server Settings >...
  • Page 169: Setting The Transparent Transmission Function

    Click in the upper left area of the Data Center Planning window. Click Access switch to the Add Device window. You can add an ECC800 device to the specified modular in the Add Device window. Figure 6-50 Adding an ECC800 device to the modular Click OK, and you can view the task information, including Type, Device Name, Region, Progress, Status, Start Time, End Time, and Information in the displayed Progress window.
  • Page 170 Step 9 In this example, a Polymer temperature and humidity (T/H) sensor is added in the equipment room of the root node. Select the device to be added and drag its icon to the management domain. Step 10 Set management attributes. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 171 Step 11 Click to save the created device view. Choose System> Configuration > Transmission Channel Management. Step 12 Click Modify after selecting the IP address of the ECC800 connected to the NMS.  If Connection mode is set to Compatible, click Confirm.
  • Page 172: Third-Party Nms Management (Over Snmp)

    Figure 6-52 Page for managing transparent transmission channels ----End 6.9.2 Third-party NMS Management (over SNMP) 6.9.2.1 Connecting the Communications Cable Procedure Step 1 Connect the communications cable to the WAN_1 port on the ECC800. Figure 6-53 Connecting the communications cable ----End 6.9.2.2 Setting SNMP Management Parameters Prerequisites Before setting SNMP parameters, obtain the information listed as follows from the NMS.
  • Page 173 SNMPv3 as an example. Procedure Step 1 Apply to the equipment room network administrator for a fixed IP address. Step 2 Set the IP address, subnet mask, and default gateway on the ECC800 WebUI. Table 6-35 IP parameters Path...
  • Page 174 For carrier users: Log in to http://support.huawei.com, download the software package of the required version from Support > Software > Carrier Cloud & Data Center > Data Center Facility > Fusion Modular Data Center > ECC800, and decompress the software package to obtain the MIB file. ----End Issue 05 (2019-09-16) Copyright ©...
  • Page 175: Maintenance

    The cable connection is Secure loose cables. connection secure. Cables are not damaged. Replace damaged cables. Table 7-2 Routine maintenance for the main control module in the ECC800 Check Item Expected Result Troubleshooting Indicator The green indicator is steady If the indicator is off or any abnormal on or blinking.
  • Page 176: Common Faults And Troubleshooting

    The ALM indicator (red) is Output overvoltage If the PSU is locked out, steady on. protection is triggered. disconnect the AC input from the PSU, and then power on the PSU again Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 177 ECC800 and independent AI_DI unit is abnormal. deployment AI_DI unit is normal. The RUN indicator is off. The contact between the Check whether the Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 178: Component Replacement

    Submit to synchronize the configuration parameters of the failure device to the reserved device. On the Monitoring > System > ECC800 > Controls tab page, select Delete device with communication failure and click Submit, add the reserved device to the smart module view.
  • Page 179 Path: Maintenance > Configuration File > Back Up Current Settings If the main control module is damaged, you may fail to log in to the ECC800. In this case, you cannot back up the settings.
  • Page 180: Replacing A Psu

    7 Maintenance Figure 7-2 Installing the Micro SD and SIM card Step 7 Install the spare ECC800 main control module in the ECC800 subrack and tighten the screws on both sides of the ECC800 main control module. Step 8 Connect the communications cables, WiFi module, and antennas to the ECC800 main control module.
  • Page 181: Replacing Ecc800 Antennas

     Materials: Spare ECC800 antennas of the same model are available and functional. Procedure Step 1 Remove the 2.4G and 3G antenna cables connected to the ports on the ECC800, as shown in Figure 7-4. Figure 7-4 Removing antennas Step 2 Install the spare 2.4G antenna and 3G antenna in the original positions and connect them to the ECC800.
  • Page 182: Replacing A Sim Card And Micro Sd Card

    Step 2 Loosen the screws on both sides of the ECC800 main control module. Step 3 Pull the handles on both sides of the ECC800 main control module, and to remove the main control module.
  • Page 183 Step 6 Install the ECC800 main control module in the card slot. Step 7 Tighten the screws on both sides of the ECC800 main control module. Step 8 Reconnect signal cables to the ECC800 main control module panel based on the recorded information.
  • Page 184: Faq

    Context A maximum of three ECC800s can be cascaded. After the IP addresses of other smart module ECC800s in the room are added to an ECC800, their active alarms and PUE data can be displayed and viewed. You can click links on the cascading management page of the master ECC800 to display the login pages of the other ECC800s.
  • Page 185: Optional) Setting Device Performance Parameters

    ECC800 Data Center Controller User Manual 8 FAQ Figure 8-1 ECC800 cascading page Step 6 (Optional) Click the alarm bubble in the Active alarms area in a smart module to view the corresponding active alarm information. Step 7 (Optional) Click the pencil icon next to a smart module name, and the Edit Smart Module Title dialog box is displayed.
  • Page 186: How Can I View Version Information

    Step 1 Log in to the ECC800 WebUI as an administrator. Step 2 Click in the upper right corner of the home page and view the ECC800 version information. Step 3 Choose Maintenance > Version Information and view the version information of ECC800 and connected device.
  • Page 187: How To Check The System Type And Set The Smart Module Name

    Go to the Re-authentication page, enter the login user name and password, and click Submit. Step 2 Choose System Settings > System Parameters > Site Configuration, modify Smart module name, and click Submit in the Site ID area. ----End Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 188: How To Manage Webui Users

    Procedure Step 1 Change the login password. Log in to the ECC800 WebUI as the administrator. Choose Maintenance > User Management. The user management page is displayed. Choose the user to be modified and click Modify. Reset the login password on the displayed page.
  • Page 189 The WebUI supports a maximum of 16 users and a maximum of 3 concurrent online users. ----End Follow-up Procedure If you forgot the password, perform the following steps: Click Forgot password. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 190: How Do I Create A Smart Module Plan View

    Step 1 Choose Home > Plan View and click Create smart module in Smart Module View. The Modify Basic Config dialog box is displayed. Set the layout and device quantity in Layout and Half-size cabinet qty./row based on the actual smart module scenario. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 191 Step 3 Hold down the BLINK button on a device such as a smart ETH gateway for less than 1s to report the blinking status to the ECC800. The corresponding device icon in the WebUI plan view blinks. Check that the device positions and types in the plan view are consistent with the actual situation by delivering the blinking command.
  • Page 192: How Do I Set And Add Devices

    One end of the straight-through cable has been connected to the FE port on the integrated UPS, and the other end has been connected to the POE port on the smart ETH gateway. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 193: How To Set And Add A Ups2000-G

    Step 3 Choose Settings > Communication, and set IP address assign to Automatic(DHCP). Step 4 Tap to go back to the main menu screen. After setting parameters for the integrated UPS, the ECC800 discovers the access from the integrated UPS automatically. ----End 8.1.8.2 How to Set and Add a UPS2000-G?
  • Page 194 UPS2000-G based on the actual situation. Click Test Connect to check whether the UPS2000-G connects to the ECC800 properly. − If the UPS2000-G connects to the ECC800 properly, click Confirm. The connected devices are displayed in the Number of connected devices list.
  • Page 195: How To Set And Add A Ups5000-E

    The section describes how to add a UPS2000-G in a single UPS scenario. In a parallel UPS scenario, if the common communications address of the Modbus card is added to the ECC800, all UPS2000-Gs can be connected to the ECC800.
  • Page 196: How To Set And Add A Pdu8000 Or Integrated Pdf (Over Modbus-Tcp)

    PDF, and the other end has been connected to the POE port on the smart ETH gateway. Context The method of connecting the PDU8000 to the ECC800 is the same as that for the integrated PDF. Connecting the integrated PDF to the ECC800 by following the instructions in this section.
  • Page 197: How To Set And Add A Pdu8000 (Over Modbus Rtu)

    8.1.8.5 How to Set and Add a PDU8000 (over Modbus RTU)? Prerequisites One end of the straight-through cable has been connected to the COM port on the PDU8000, and the other end has been connected to the COM port on the ECC800 collector, rack environment unit, or ETH converter. Procedure Step 1 Set the PDU8000 monitoring parameters.
  • Page 198: How To Set And Add A Pdu2000

    One end of the straight-through cable has been connected to the COM 1 or COM 2 port on the PDU2000, and the other end has been connected to the COM port on the ECC800 collector, rack environment unit, or ETH converter.
  • Page 199 The parameter settings take effect only if you press MENU and then the PDU2000-M (C) buzzes and restarts. If you do not press MENU, the PDU2000-M (C) buzzes and restarts automatically after 30s and the settings are not saved.  Set the PDU2000-M (H) monitoring parameters Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 200 Port NOTE are displayed. The setting example indicates that the PDU2000 is connected to the COM1 port on the ECC800. If the PDU2000 is connected to another port, enter the number of the connected port. Device Address Enter the actual device address of the PDU2000.
  • Page 201: How To Set And Add An Ats

    8.1.8.7 How to Set and Add an ATS? Prerequisites One end of the straight-through cable has been connected to the COM port on the ATS, and the other end has been connected to the COM port on the ECC800 collector, rack environment unit, or ETH converter. Context The ATS (ABB) model is OMD800.
  • Page 202: How To Set And Add A Pmac615 Ac Meter

    Prerequisites One end of the straight-through cable has been connected to the RS485 port on the PMAC615 AC meter, and the other end has been connected to the COM port on the ECC800. Context The model of the single-phase AC meter for the lighting control box is PMAC615.
  • Page 203: How To Set And Add A Pmac625 Ac Meter

    8.1.8.9 How to Set and Add a PMAC625 AC Meter? Prerequisites One end of the straight-through cable has been connected to the RS485 port on the PMAC625 AC meter, and the other end has been connected to the COM port on the ECC800. Context ...
  • Page 204 , and then press to save the setting. Figure 8-18 Communications address of the PMAC625 Step 2 Add a PMAC625. Log in to the ECC800 WebUI as an administrator. Add a PMAC625. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 205: How To Set And Add A Pdc Dc Meter

    Prerequisites One end of the straight-through cable has been connected to the RS485 port on the PDC DC meter, and the other end has been connected to the COM port on the ECC800. Context The model of the PDC is PDU8000-0630DCV5-HVA002 and the BOM number is 02403121.
  • Page 206 Number of connected devices list. − If the PDC DC meter does not connect to the ECC800 properly, check whether the cable between the PDC DC meter and the ECC800 is connected properly, whether the PDC DC meter and ECC800 are running properly, and whether the input parameters are consistent with the PDC DC meter parameters.
  • Page 207: How To Set And Add An Ac Pdc Ma01C

    In this example, Device Address is set to 1. During actual configuration, set the device address based on the actual situation. Click Test Connect to check whether the AC PDC MA01C connects to the ECC800 properly. − If the AC PDC MA01C connects to the ECC800 properly, click Confirm. The connected devices are displayed in the Number of connected devices list.
  • Page 208: How To Set And Add A Netcol5000-A042 Parameters

    Choose Settings > Comm Settings > Modbus Settings, and set Connection mode to Server and client, Server encryption to Enable. After the NetCol5000-A042 parameters are set, the ECC800 can automatically identify the automatic access of the NetCol5000-A042. Step 2 Set the running parameters and control parameters for the 42 kW smart cooling product on the ECC800 WebUI.
  • Page 209: How To Set And Add A Netcol5000-C030 (Over Modbus Rtu)

    Choose Settings > Comm Settings > Modbus Settings, and set Connection mode to Server and client, Server encryption to Enable.  After setting parameters for the NetCol5000-C030, the ECC800 discovers the access from the smart cooling product automatically.  The earlier version has Protocol setting on the screen. The actual screen prevails.
  • Page 210 In this example, Device Address is set to 1. During actual configuration, set the device address for the NetCol5000-C030 based on the actual situation. Click Test Connect to check whether the NetCol5000-C030 connects to the ECC800 properly. − If the NetCol5000-C030 connects to the ECC800 properly, click Confirm. The connected devices are displayed in the Number of connected devices list.
  • Page 211: How To Set And Add A Netcol5000-A025 Parameters (Over Mac-Modbus)

    Choose Settings > Comm Settings > Modbus Settings, and set Connection mode to Server and client, Server encryption to Enable. After the NetCol5000-A025 parameters are set, the ECC800 can automatically identify the automatic access of the NetCol5000-A025. Step 2 Set the running parameters and control parameters for the 25 kW smart cooling product on the ECC800 WebUI.
  • Page 212: How To Set And Add A Netcol5000-A025 Parameters (Over Modbus-Tcp)

    Choose Settings > Comm Settings > Modbus Settings, and set Connection mode to Server and client, Server encryption to Enable. After the NetCol5000-A025 parameters are set, the ECC800 can automatically identify the automatic access of the NetCol5000-A025. Step 2 Set the running parameters and control parameters for the 25 kW smart cooling product on the ECC800 WebUI.
  • Page 213: How To Set And Add A Netcol5000-A010 Parameters(Over Mac-Modbus)

    NetCol5000-A010 main control board, and the other end has been connected to the POE port on the ETH converter. Procedure Step 1 Set the running parameters and control parameters for the NetCol5000-A010 on the ECC800 WebUI. Log in to the ECC800 WebUI as an administrator.
  • Page 214: How To Set And Add A Netcol5000Cf_110 Parameters (Over Modbus-Tcp)

    NetCol5000CF_110 main control board, and the other end has been connected to the POE port on the smart ETH gateway. Context The chilled water smart cooling product is displayed as NetCol5000CF_110 on the ECC800 WebUI and the corresponding smart cooling product is NetCol5000-C(065, 080). Procedure Step 1 Set the NetCol5000CF_110 monitoring parameters.
  • Page 215: How To Set And Add A Sunrise Scu-20K

    If multiple SUNRISE-SCU-20K devices are connected to a same smart module, ensure that each  monitoring address of a SUNRISE-SCU-20K is unique. Step 2 Add a SUNRISE-SCU-20K. Log in to the ECC800 WebUI as an administrator. Add a SUNRISE-SCU-20K. Table 8-14 Adding a SUNRISE-SCU-20K Path...
  • Page 216 In this example, Device Address is set to 2. During actual configuration, set the device address based on the actual situation. Click Test Connect to check whether the SUNRISE-SCU-20K connects to the ECC800 properly. − If the SUNRISE-SCU-20K connects to the ECC800 properly, click Confirm. The connected devices are displayed in the Number of connected devices list.
  • Page 217: How To Set And Add A Rack-Mounted Hr04A

    In this example, Device address is set to 1. During actual configuration, set the device address based on the actual situation. Click Test Connect to check whether the rack-mounted HR04A connects to the ECC800 properly. − If the rack-mounted HR04A connects to the ECC800 properly, click Confirm. The connected devices are displayed in the Number of connected devices list.
  • Page 218: How Do I Add And Set An Airsys Air Conditioner

    8.1.8.22 How Do I Add and Set an AIRSYS Air Conditioner? Procedure Step 1 Add an AIRSYS air conditioner. Log in to the ECC800 WebUI as an administrator. Add an AIRSYS air conditioner. Table 8-16 Adding an AIRSYS air conditioner...
  • Page 219: How To Set And Add A Dehumidifier Ht-500

    8.1.8.23 How to Set and Add a Dehumidifier HT-500? Prerequisites One end of the straight-through cable has been connected to the RS485 port on the Dehumidifier HT-500, and the other end has been connected to the COM port on the ECC800 collector. Procedure Step 1 Log in to the ECC800 WebUI as an administrator.
  • Page 220: How To Set And Add An Ip Device

    IP devices, such as ATMs, are devices with IP attributes in an equipment room or site. By adding an IP device, you connect the device to the ECC800 in the same network so that the ECC800 monitors the device status. If the IP device is offline, the ECC800 will report a disconnection alarm on its WebUI.
  • Page 221: How To Set And Add An Independent Deployment Ai_Di Unit

    One end of the straight-through cable has been connected to the COM_IN port on the independent deployment AI_DI unit, and the other end has been connected to the COM port on the ECC800 collector, rack environment unit, or ETH converter. Procedure Step 1 Set monitoring parameters for the independent deployment AI_DI unit.
  • Page 222: How To Set And Add The Multi-Functional Sensor

    Confirm. The connected devices are displayed in the Number of connected devices list. If the independent deployment AI_DI unit does not connect to the ECC800 properly, check whether the cable between the independent deployment AI_DI unit and the ECC800 is connected properly, whether the independent deployment AI_DI unit and ECC800 are running properly, and whether the input parameters are consistent with the parameters of the independent deployment AI_DI unit.
  • Page 223 After the commissioning is  complete, clean up dust. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 224: How To Set And Add The Smoke Detector (Connected To The Ai/Di Port On The Ecc800)

    Prerequisites  Connecting Cables to the Smoke sensor(NC): The smoke detector has been connected to the AI/DI port on the ECC800 collector using a network cable. To connect the cable for the smoke detector, perform the following steps: Short-circuit core wires 1 and 8 on the other end of the network cable, and connect the network cable to the cable delivered with the smoke detector.
  • Page 225 Procedure Step 1 Set smoke detector parameters. In this example, the smoke detector is connected to the AI/DI_2 port on the ECC800. Log in to the ECC800 WebUI as an administrator. Choose System Settings > Signal Name Modify. The Batch Signal Configuration page is displayed.
  • Page 226: How To Set And Add The Smoke Detector (Connected To The Ai/Di Port On The Skylight Actuator)

    Step 1 Set smoke sensor parameters. In this example, the smoke sensor is connected to the AI/DI_1 port on the skylight actuator. Log in to the ECC800 WebUI as an administrator. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 227: How To Set And Add The Smoke Detector (Connected To The Ai/Di Port On The Rack Environment Unit)

    In this example, the smoke sensor is connected to the AI/DI_1 port on the rack environment unit. Log in to the ECC800 WebUI as an administrator. Choose Monitoring > Cabinet > IT Cabinet n > Cabinet Collector n > Running Parameters.
  • Page 228: How To Set And Add The Wlds900 Water Sensor

    If a water sensor is installed, perform the following steps to configure it. Prerequisites One end of the straight-through cable has been connected to the RJ45 port on the WLDS900 water sensor, and the other end has been connected to the AI/DI port on the ECC800. Context ...
  • Page 229: How To Set And Add The Wlds600 Water Sensor

    Step 4 Click Test Connect to check whether the water sensor connects to the ECC800 properly. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 230: How To Set And Add The Electrode Water Sensor

    Number of connected devices list.  If the water sensor does not connect to the ECC800 properly, check whether the cable between the water sensor and the ECC800 is connected properly, whether the water sensor and ECC800 are running properly, and whether the input parameters are consistent with the water sensor parameters.
  • Page 231: How To Set And Add The Temperature Sensor (Connected To The Ai/Di Port On The Ecc800)

    ECC800 Data Center Controller User Manual 8 FAQ In this example, the water sensor is connected to the AI/DI_3 port on the ECC800. Log in to the ECC800 WebUI as an administrator. Choose System Settings > Signal Name Modify. The Batch Signal Configuration page is displayed.
  • Page 232: How To Set And Add The Temperature Sensor (Connected To The Ntc Port On The Rack Environment Unit)

    Choose System Settings > Signal Name Modify. The Batch Signal Configuration page is displayed. Set Device Type to ECC800, set Device Name to ECC800, and click OK. On the query result tab page, set the new signal name of AI/DI_2 to Temperature and click Submit.
  • Page 233: How To Set And Add The T/H Sensor (Bom Number: 33010346)

    Prerequisites One end of the straight-through cable has been connected to the RJ45 port on the temperature sensor, and the other end has been connected to the COM port on the ECC800. Procedure Step 1 Set the T/H sensor device address.
  • Page 234: How To Set And Add The T/H Sensor (Bom Number: 02310Nbs)

    Prerequisites One end of the straight-through cable has been connected to the RS485_IN port on the T/H sensor, and the other end has been connected to the COM port on the ECC800. Procedure Step 1 Set the T/H sensor device address.
  • Page 235 Number of connected devices list. − If the T/H sensor does not connect to the ECC800 properly, check whether the cable between the T/H sensor and the ECC800 is connected properly, whether the T/H sensor and ECC800 are running properly, and whether the input parameters are consistent with the T/H sensor parameters.
  • Page 236: How To Set And Add The T/H Sensor (Bom Number: 02311Fqg)

    Prerequisites One end of the straight-through cable has been connected to the RS485_IN port on the T/H sensor, and the other end has been connected to the COM port on the ECC800. Procedure Step 1 Set the T/H sensor device address.
  • Page 237 Number of connected devices list. − If the T/H sensor does not connect to the ECC800 properly, check whether the cable between the T/H sensor and the ECC800 is connected properly, whether the T/H sensor and ECC800 are running properly, and whether the input parameters are consistent with the T/H sensor parameters.
  • Page 238: How To Restore Factory Settings

    ECC800 WebUI.  You need to apply to an organization authorized by the customer for a network security certificate and its key with the ECC800 IP address or domain name. This section describes how to import the certificate and key. Procedure Step 1 Log in to the ECC800 WebUI as the administrator.
  • Page 239: How Can I Install A Device Access Certificate

    You have obtained a device access certificate and the certificate key and have copied the certificate and key file to the PC.  A preset certificate is provided for the ECC800 and its connected devices. If a higher security level is required, replace the certificate both on the ECC800 and the devices. ...
  • Page 240: How Do I Configure Ecc800 Alarm Parameters

    Step 5 On the Alarm Linkage page, set Device type to ECC800, select Device Type or Device in the Linkage type column, and click Confirm. Step 6 (Optional) If you select Device in the Linkage type column, select the ECC800 to be set in the Device name column.
  • Page 241: How Can I View Real-Time Monitoring Data, Active Alarms, Historical Alarms, Access Event, And Operation Logs

    Step 2 Click Monitoring, select the device to be viewed, and select Running Info to view the real-time data of the device. Step 3 Choose Home > Active Alarms to view the active alarms of the ECC800. Click Details in the Alarm Details area to view alarm details of devices.
  • Page 242: How Can I View Performance Data

    8.1.17 How Is a Signal Name Changed? Context  In this example, the smoke sensor is connected to the AI/DI_3 port on the ECC800.  The following procedure describes how to change the signal name of AI/DI_3. Other signal names can be changed in a similar way.
  • Page 243: How Can I Export Or Import A Configuration File

    ECC800_2 and ECC800_1 must have the same type and number of connected devices. Procedure Step 1 Log in to the ECC800_1 WebUI as an administrator. Step 2 Choose Maintenance > Configuration File. Step 3 Export a configuration file. Specify Configuration file encryption password. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 244: How Can I Export Fault Information

    Encryption password for export. Record the password for decompressing the data package. Step 4 Export fault information and save the exported data to the PC or USB flash drive. Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 245: How Can I Synchronize Device Parameters

    Step 3 Select a value from the Device type drop-down list box. Step 4 Specify source device and target device, click Submit. If communication between the ECC800 and the device is interrupted during parameter synchronization, the synchronization fails. Ensure that the ECC800 and the device communicate properly and synchronize parameters again.
  • Page 246: How Can I Handle Do Association Failure

    If DO association fails, the DO port to be associated may be used by other functions. Check whether the DO port is used.  Two ECC800 functions may use a DO port: Linkage control and alarm linkage. Procedure Step 1 Log in to the ECC800 WebUI as an administrator.
  • Page 247: What Do I Do If A Message Indicating Unauthorized Fingerprint Is Displayed During Fingerprint Scanning On The Access Control Device (Fingerprint Has Been Recorded)

    ----End 8.1.26 How Can I Rectify Camera Access Restriction? Prerequisites If Huawei S12700 series switch is used, refer to this section to rectify the fault. For more information, consult network engineers. Context The camera is inaccessible after the MAC address and IP address are bound in network configuration.
  • Page 248: How Should I Add The Devices Accessed Through A Smart Eth Gateway Over Modbus-Tcp To The Ecc800 Webui

    Figure 8-25 Network diagram Procedure Step 1 Ensure that the device communication mode has been set to DHCP. Step 2 Log in to the ECC800 WebUI as an administrator, and check whether the device exists on the Monitoring page. ...
  • Page 249: How Should I Add The Devices Accessed Through A Smart Eth Gateway Over Modbus-Mac To The Ecc800 Webui

    The device that supports Modbus-MAC can be automatically identified by the ECC800. Figure 8-27 Network diagram Procedure Step 1 Log in to the ECC800 WebUI as an administrator, and check whether the device exists on the Monitoring page. The following is an example of confirming the access of a WiFi converter.
  • Page 250: How Should I Add Devices Accessed Through The Eth Converter To The Ecc800 Webui

    ----End Follow-up Procedure Choose Home > Plan View on the ECC800 WebUI, and drag the device to the corresponding position in the Smart Module View pane based on the actual device layout. 8.1.29 How Should I Add Devices Accessed Through the ETH...
  • Page 251 − If the connection is not proper, check that the cable is properly connected between the device and the ECC800, that the device and ECC800 are running properly, and that the input parameters are consistent with the device parameters. Issue 05 (2019-09-16)
  • Page 252: How Should I Add Devices Accessed Through The Ecc800 Com Port To The Ecc800 Webui

    ----End Follow-up Procedure Choose Home > Plan View on the ECC800 WebUI, and drag the device to the corresponding position in the Smart Module View pane based on the actual device layout. 8.1.30 How Should I Add Devices Accessed Through the ECC800...
  • Page 253: How Should I Add Devices Accessed Through The Ecc800 Ai/Di Port To The Ecc800 Webui

    ----End Follow-up Procedure Choose Home > Plan View on the ECC800 WebUI, and drag the device to the corresponding position in the Smart Module View pane based on the actual device layout. 8.1.31 How Should I Add Devices Accessed Through the ECC800...
  • Page 254 Step 3 After setting all mandatory parameters, click Submit. ----End Follow-up Procedure Choose Home > Plan View on the ECC800 WebUI, and drag the device to the corresponding position in the Smart Module View pane based on the actual device layout. Issue 05 (2019-09-16)
  • Page 255: How Should I Open Doors Remotely Over The Ecc800 Webui

    Context If O&M personnel need to enter a smart module but do not take an access cord or forget the password, you can open the door remotely over the ECC800 WebUI. Procedure Step 1 Log in to the ECC800 WebUI as an administrator.
  • Page 256: How Should I Turn On Or Off Aisle Lights In The Smart Module Over The Ecc800 Webui

    ECC800 WebUI. Procedure Step 1 Log in to the ECC800 WebUI as an administrator. Step 2 Turn on or off aisle lights. Table 8-44 Operations for turning on or off aisle lights...
  • Page 257: How Should I Opening Skylights Remotely Over The Ecc800 Webui

    8.1.34 How Should I Opening Skylights Remotely over the ECC800 WebUI? Context You can open skylights over the ECC800 WebUI in emergencies. Procedure Step 1 Log in to the ECC800 WebUI as an administrator. Step 2 Open skylights. Table 8-45 Operations for opening skylights Path Setting Monitoring >...
  • Page 258: How Should I Turn On Or Off Smart Cooling Products Over The Ecc800 Webui

    8.1.35 How Should I Turn On or Off Smart Cooling Products over the ECC800 WebUI? Context You can turn on or off smart cooling products over the ECC800 WebUI in emergencies. Procedure Step 1 Log in to the ECC800 WebUI as an administrator.
  • Page 259: How Should I Link The Smoke Alarm With The Alarm Beacon Over The Ecc800 Webui

    8.1.37 How Should I Link the Smoke Alarm with the Alarm Beacon over the ECC800 WebUI Prerequisites The alarm beacon is connected to the DO port on the ECC800. Context This section describes how to set an alarm linkage by linking output dry contact of the smoke alarm on the multi-functional sensor to the DO2 port.
  • Page 260: How Should I Link The Ai/Di Alarm With The Alarm Beacon Over The Ecc800 Webui

    Procedure Step 1 Choose System Settings > Alarm Parameter > Alarm Linkage. Step 2 Select ECC800 for Device type, select Device Type or Device for Linkage type, and click Confirm. Select ECC800 from the Device name list if you have selected Device for Linkage type, and click Confirm.
  • Page 261: How Should I Modify Device Names Over The Ecc800 Webui

     The following describes how to modify the name of the smart ETH gateway. Procedure Step 1 Log in to the ECC800 WebUI as an administrator. Step 2 Modify the device name. Table 8-48 Operations for modifying a device name...
  • Page 262: App Operations

    You have obtained the IP address of the ECC800 as well as the user name and password used for WebUI login.  A PC with an IP address in the same network segment as that of the ECC800 is prepared, and the PC has connected to port WAN_1 on the ECC800. Procedure Step 1 Download and obtain the app installation package using any of the following three methods: ...
  • Page 263 After you open the HUAWEI App Store, select NOT NOW if "New Version" is displayed.  Log in to the ECC800 WebUI using a PC. Choose Maintenance > App Obtaining, scan QR code, and save the app installation package to the PC or a path on the mobile storage device.
  • Page 264: How Do I Ensure That Device Positions In The Plan View Are Consistent With Actual Positions

     It is recommended that you use different user names to log in to both the ECC800 WebUI and app at the same time. If you use the same user name to log in to the WebUI and app at the same time, either of them will be forcibly logged out.
  • Page 265: How To View Real-Time Data

    8.2.4 How to View Real-time Data? Procedure Step 1 Log in to the ECC800 mobile phone or pad app as an administrator. Step 2 To view the smart module data center layout, tap Home. Step 3 To view active alarms and historical alarms, choose Alarms > Active Alarms or Alarms >...
  • Page 266: How Can I Synchronize Device Parameters

    After a device is replaced, you can synchronize the parameters of the original device to the new device. Procedure Step 1 Log in to the ECC800 mobile phone or pad app as an administrator. Step 2 Choose Parameter Sync. ...
  • Page 267: How Can I Handle App Login Failure

    Step 1 If you have obtained the user name and password used in the previous successful login, perform the following operations: Check that the mobile phone or pad connects to the ECC800 over WiFi properly. Use the obtained user name and password to log in to the app and exit.
  • Page 268: Plc Function

    PLC Function 9.1 Linkage Control Introduction The ECC800 provides the linkage control function. You can set logic rules and control the DO output signal by collecting the signal value. You can select signals (such as the AI/DI device status signals) and perform logic operations such as AND, OR, NOT, GREATER THAN, LESS THAN, DELAY, and FILTER.
  • Page 269: Linkage Control Configuration Examples

     The ECC800 supports fire control linkage and high temperature linkage control. For example, the ECC800 can implement fire linkage by detecting fire alarms through the fire controller and opening the skylight, opening the aisle door, and shutting down the smart cooling product based on the alarm status.
  • Page 270 When adding high temperature linkage control, ensure that all smart cooling products fail to communicate with the ECC800. If smart cooling products communicate properly, cooling can be automatically implemented when the smart cooling products are at high temperature. Opening the skylights may cause the cooling effect to fail.
  • Page 271 You can use the configuration file import and export function to export the linkage control linkage rules configured for an ECC800 to a local PC and then import the rules to another ECC800. This function achieves quick configuration for the linkage control.
  • Page 272: Acronyms And Abbreviations

    Advanced encryption standard analog input application battery control I/O board component object model direct current Data Encryption Standard digital input digital output energy control center equipment serial number Ethernet Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 273 Media Access Control message digest algorithm network address translation NetEco iManager NetEco data center infrastructure management system negative temperature coefficient power distribution unit power over Ethernet power supply unit power usage effectiveness Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.
  • Page 274 Simple Mail Transfer Protocol SNMP Simple Network Management Protocol Secure Sockets Layer SSID service set identifier Transport Layer Security uninterruptible power system universal serial bus video cloud node WiFi wireless fidelity WiFi protected setup Issue 05 (2019-09-16) Copyright © Huawei Technologies Co., Ltd.

Table of Contents