8.2 Overview
Section
Display and display number
8.4 Status (1)
8.4.1
Actual alarms (3.1)
8.4.2
System (1.2)
8.4.3
Operating mode (1.2.1)
8.4.4
Setpoint (1.2.2)
8.4.5
Setpoint influence (1.2.3)
8.4.6
Measured values (1.2.4)
8.4.7
Analog inputs (1.2.5)
8.4.8
Log graph (1.2.6)
8.4.9
Battery status (1.2.7)
8.4.10
Pump 1 - 6, Pilot pump, Backup pump (1.3 - 1.10)
8.5 Operation (2)
8.5.1
Operation (2)
8.5.2
System operating mode (2.1.1)
8.5.3
Control mode (2.1.2)
8.5.4
Alternative setpoints (2.1.3)
8.5.5
Individual pump control (2.1.4)
8.5.6
Pump 1 - 6 (2.1.4.1 - 2.1.4.6)
8.5.7
Operation, pilot pump (2.1.4.7)
8.5.8
Operation, backup pump (2.1.4.8)
8.6 Alarm (3)
8.6.1
Alarm status (3)
8.6.2
Actual alarms (3.1)
8.6.3
Alarm log (3.2)
8.6.4
Service contact information (3.3)
8.7 Settings (4)
8.7.1
Primary controller (4.1)
8.7.2
PI controller (4.1.1)
8.7.3
Alternative setpoints (4.1.2)
8.7.4
Alternative setpoints 2 - 7 (4.1.2.1 - 4.1.2.7)
8.7.5
External setpoint influence (4.1.3)
8.7.6
Setting of influence function (4.1.3.2)
8.7.7
Primary sensor (4.1.4)
8.7.8
Clock program (4.1.6)
8.7.9
Proportional pressure (4.1.7)
8.7.10
S-system configuration (4.1.8)
8.7.11
Setpoint ramp (4.1.9)
8.7.12
Pump cascade control (4.2)
8.7.13
Min. time between start/stop (4.2.1)
8.7.14
Max. number of starts/hour (4.2.1)
8.7.15
Standby pumps (4.2.3)
8.7.16
Forced pump changeover (4.2.4)
8.7.17
Pump test run (4.2.5)
8.7.18
Pump stop attempt (4.2.7)
8.7.19
Pump start and stop speed (4.2.8)
8.7.20
Min. performance (4.2.9)
8.7.21
Compensation for pump start-up time (4.2.10)
8.7.22
Secondary functions (4.3)
8.7.23
Stop function (4.3.1)
8.7.24
Soft pressure build-up (4.3.3)
8.7.25
Emergency run (4.3.5)
8.7.26
Digital inputs (4.3.7)
8.7.27
Functions of digital inputs (4.3.7.1)
8.7.28
Analog inputs (4.3.8)
8.7.29
Analog inputs (4.3.8.1 to 4.3.8.7)
8.7.30
Analog inputs and measured value (4.3.8.1.1 - 4.3.8.7.1)
12
See page
14
14
15
15
15
16
16
16
16
17
17
18
18
18
19
21
21
22
22
23
24
24
25
25
25
26
26
27
28
28
29
30
30
31
32
32
33
33
33
33
34
34
35
35
36
36
37
37
37
39
40
40
41
41
42
42
Need help?
Do you have a question about the Control MPC and is the answer not in the manual?
Questions and answers