Grundfos Control MPC Installation And Operating Instructions Manual page 11

Continued from page 10
4. Settings
4.1 Primary controller
4.1.1 PI controller
4.1.2 Alternative setpoints
4.1.2.1 Alternative setpoints 2 - 7
4.1.3 External setpoint influence
4.1.3.1 Input value to be influenced by
4.1.4 Primary sensor
4.1.6 Clock program
4.1.7 Proportional pressure
4.1.8 S-system configuration
4.1.9 Setpoint ramp
4.2 Pump cascade control
Min. time between start/stop
4.2.1
Max. number of starts/hour
4.2.3 Standby pumps
4.2.4 Forced pump changeover
4.2.5 Pump test run
4.2.7 Pump stop attempt
4.2.8 Pump start and stop speed
4.2.9 Min. performance
4.2.10 Compensation for pump start-up time
4.3 Secondary functions
4.3.1 Stop function
4.3.1.1 Stop parameters
4.3.3 Soft pressure build-up
4.3.5 Emergency run
4.3.7 Digital inputs
4.3.8 Analog inputs
Setting, AI1 (CU 352), [51] - AI3, [51, 54, 57]
Setting, AI1 (IO 351-41), [57] - AI2 [57, 60]
Setting, AI1 (IO 351-42), [57] - AI2 [57, 60]
4.3.9 Digital outputs
DO1 (CU 352), [71] is signalling - DO2 [71, 74]
DO1 (IO 351-41), [77] is signalling - DO7 [77 - 88]
DO1 (IO 351-42), [77] is signalling - DO7 [77 - 88]
4.3.10 Analog outputs
AO1 (IO 351-41) [18] - AO3 [18, 22, 26]
AO1 (IO 351-42) [18] - AO3 [18, 22, 26]
4.3.14 Min., max. and user-defined duty
4.3.14. Min. duty
4.3.14. Max. duty
4.3.14. Set user-defined duty
4.3.19 Pump curve data
4.3.23
4.3.20 Control source
4.3.22 Fixed inlet pressure
4.3.23 Flow estimation
4.3.24 Reduced operation
4.4 Monitoring functions
4.4.1 Dry-running protection
4.4.1.1 Pressure/level switch
4.4.1.2 Measurement, inlet pressure
4.4.1.3 Measurement, tank level
4.4.2 Min. pressure
4.4.3 Max. pressure
4.4.4 External fault
4.4.5 Limit 1 exceeded
4.4.6 Limit 2 exceeded
4.4.7 Pumps outside duty range
4.4.8 Pressure relief
4.4.9 Log values
4.4.10 Fault, primary sensor
4.5 Functions, CU 352
Change language to the service language
Run wizard again
4.5.1 Display language
4.5.2 Units
4.5.2.1 Pressure
4.5.2.2 Differential pressure
4.5.2.3 Head
4.5.2.4 Level
4.5.2.5 Flow rate
4.5.2.6 Volume
4.5.2.7 Specific
4.1.3.2 Setting of influence function
Function, DI1 (CU 352) - DI3, [10, 12, 14]
Function, DI1 (IO 351-41) - DI9, [10 - 46]
Function, DI1 (IO 351-42) - DI9, [10 - 46]
Function, AI1 (CU 352) - AI3 [51, 54, 57]
Function, AI1 (IO 351-41) - AI2 [57, 60]
Function, AI1 (IO 351-42) - A2 [57, 60]
Flow estimation
4.5.2.8 Temperature
4.5.2.9 Power
4.5.2.10 Energy
4.5.3 Date and time
4.5.4 Password
4.5.5 Ethernet
4.5.6 GENIbus number
4.5.9 Software status
11