GE MULTILIN 269 MOTOR MANAGEMENT RELAY Series Instruction Manual page 135

negative sequence current, 1-1, 3-45, 3-56, 5-3
O
output relays, 1-1, 2-12, 2-15, 3-4, 3-25, 3-33, 3-44, 3-
51, 4-5, 5-1, 6-1
overload curve, 1-2, 3-44, 3-52, 3-55, 3-56, 3-58, 4-5,
6-1
overload pickup, 3-44, 3-56
overload trips, 3-57
overload warning, 3-49
overvoltage, 3-38
P
PF protection, 3-38
phase CT primary, 2-15, 3-36
phase reversal, 1-2, 3-40, 3-59
positive kvar, 3-40
positive sequence current, 3-7, 3-12, 3-45, 4-4, 5-3
power consumption, 2-12
power factor, 2-24, 3-15, 3-39, 3-40, 3-58, 3-59
power measurement conventions, 3-59
pulsating loads, 3-46
R
register, 3-55, 5-1, 5-3
relay commissioning, 4-1
remote reset, 2-18
reset, 2-15, 2-18, 3-4, 3-57, 5-1
resetting, 3-16
residual, 2-15
restart, 2-18, 3-4
RS485, 1-5
RTD, 1-1, 1-2, 1-5
alarm, 3-43, 3-61
average stator RTD temperature, 5-3
bearing, 3-29, 3-51, 4-4
bias, 3-27, 3-44, 3-51, 3-55, 3-57, 4-5
broken sensor alarm, 3-26
circuitry, 4-1
hottest stator RTD, 2-18, 3-8, 4-5
inputs, 4-4
low temp alarm, 3-26
max stator RTD temperature, 3-57
maximum stator RTD temperature, 3-7, 3-9, 3-12
measurement tests, 4-4
motor RTD temperature, 4-5
open RTD, 3-51
other, 3-50, 3-51
potentiometers, 4-4
resistance, 4-4
sensor connections, 2-17
sensor type, 3-21
setpoints, 3-2, 3-21, 3-50
stator, 2-7, 2-15, 2-16, 3-16, 3-27, 3-42, 3-50, 3-
51, 4-4, 4-5
stator RTD temperature, 3-27, 3-56
stator RTD voting, 3-27, 4-4
temperature, 3-2, 3-4, 3-8, 4-5
trip, 3-42, 3-61
running hours, 1-2, 3-11, 3-58
S
serial number identifier, 3-34
short circuit, 2-12, 2-15, 2-16, 3-50, 4-1, 4-5, 5-1, 6-1
software access, 3-34
software access code, 2-19
solidly grounded system, 2-15
spare input, 3-31
specifications, 1-5, 1-7
standard overload curve, 1-2
standard overload curves, 1-2
starter, 2-15, 2-16
starting current, 3-7, 3-14, 3-56
starts/hour, 2-18, 3-16, 3-44, 3-57
synchronous motor, 3-59
synchronous motors, 3-58
T
temperature, 1-1, 1-2, 2-17, 3-56, 3-58, 5-1, 6-1
test analog output, 4-5
thermal capacity used, 2-18, 3-10, 3-29, 3-55, 3-56, 3-
57, 4-5, 6-1
thermal model, 1-1, 3-56
time between starts, 2-18, 3-16, 3-45
timers, 3-7, 5-1, 5-3
timing, 4-1
trip relay, 1-1, 1-2, 2-9, 2-16, 3-5, 3-31, 4-5
trips, 2-7, 2-16, 2-17, 2-18, 3-16, 3-26, 3-45, 3-49, 3-
57, 3-59, 4-5
two-wire isolated transmitter, 2-19
U
unbalance, 1-1, 1-2, 1-5, 2-15, 2-16, 3-42, 3-43, 3-44,
3-45, 3-51, 3-56, 4-1, 4-4, 4-5, 5-3
unbalance bias, 3-28
unbalance K factor, 3-28
undercurrent, 2-16, 3-49
undervoltage, 3-37
V
voltage phase reversal, 2-24
W
wiring, 2-12, 3-44
INDEX