Related Manuals for Advantech FWA-3240
Summary of Contents for Advantech FWA-3240
- Page 1 FWA-3240 Manual 1U Rackmount Intel Tolapai-based Platform with 4 Front LAN Ports & LCD Display...
- Page 2 CE Notification The FWA-3240, developed by Advantech Co., Ltd., has passed the CE test for environment specifications when shielded cables are used for external wiring. We recommend the use of shielded cables.
- Page 3 Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.
- Page 4 One CD-ROM for user manual (PDF file) If any of these items are missing or damaged, contact your distributor or sales representative immediately. Technical Support and Sales Assistance If you have any technical questions about the FWA-3240 or any other Advantech products, please visit our support website at: http://www.advantech.com.tw/support http://www.advantech.com.
-
Page 5: Table Of Contents
~ Contents ~ 1. General Information ............1 Introduction ................1 Features ................. 2 Specifications ................2 Dimensions ................3 Block Diagram ................3 2. System Setup ..............4 Removing the cover ..............4 Installing Memory Module ............5 Installing Hard Disk Drive ............6 Installing Compact Flash ............ -
Page 6: General Information
The FWA-3240 features a low-power design, and supports up to 2 GB DDR2 on one single-channel SO-DIMM. It provides a total of four GbE LANs, three of which are from the Tolapai on-chip MACs (Intel 82574-derived) and the fourth from a PCle-based Intel 82574 Ethernet controller. -
Page 7: Features
1.2 Features 1U Rackmount Network Application Platform Intel EP80579 Integrated Processor (Tolapai) solution One internal proprietary PCle x4 expansion slot Single channel DDR2 SODIMM support up to 2 GB 4 X 10/100/1000 Mbps GbE LAN ports Console port for local setting 1.3 Specifications CPU &... -
Page 8: Dimensions
1.4 Dimensions 1.5 Block Diagram... -
Page 9: System Setup
CPU, RAM, HDD, and etc. The front panel of FWA-3240 includes a LCD display module, four Ethernet ports, aRS-232 console port, and two LEDs where one is power LED and another is HDD LED. On the rear panel, there is a power switch located on the top right hand corner. -
Page 10: Installing Memory Module
2.2 Installing Memory Module 1. Unlock a DIMM socket by. Align the notch of the DIMM memory module to match on the socket and insert the DIMM into the socket until the DIMM is properly seated. 2. Press the DIMM inward to lock the DIMM memory module. Installing memory module is completed. Figure 2-3: Install RAM module... -
Page 11: Installing Hard Disk Drive
2.3 Installing Hard Disk Drive 1. Unscrew each side of the HDD supporting frame on the chassis and pull it out. 2. Put the HDD above the HDD supporting frame and position the screws accordingly. 3. Screw each side of the HDD supporting frame to fix on the chassis. 4. -
Page 12: Installing Compact Flash
2.4 Installing Compact Flash 1. Position a CompactFlash disk accordingly in the CompactFlash disk socket and push it inward. Installing CompactFlash disk is completed. Figure 2-5: Install CF card... -
Page 13: Hardware Overview
Hardware Overview 3.1 System Block Diagram 3.1.1 NAMB-3240 Main Board Block Diagram Figure 3-1: NAMB-3240 Main Board Block Diagram... -
Page 14: Feature Summary
3.2 Feature Summary 3.2.1 NAMB-3240 Main Board hardware function Table 3-1: Overview of the NAMB-3240 major hardware function Integrated chipset Tolapai 65nm packed in 1088-Ball FCBGA, 3.75cm x 3.75cm Processor with 256K L2 Cache, (CPU + NB + SB chipset) FSB 400/533 600MHz/1.0 Ghz/2.0 Ghz One DIMM socket supporting DDR2 SODIMM technology memory. -
Page 15: Hardware Jumper Guide
Hardware Jumper Guide 4.1 PCA Placement 4.1.1 Main Board Placement Figure 4-1: NAMB-3240 Placement... -
Page 16: Connector
4.2 Connector 4.2.1 Power Supply Connector Pin-out The motherboard shall accommodate power connectors as described in the AT Specifications. The main connector shall be 7-pin connector as specified in the AT-12V Power Supply Design Guide as referenced above. Figure 4-2: Power Supply Connector 1x7Pin(CN2) 4.2.2 Clear CMOS Header Use a three pin header. -
Page 17: Fan Header
4.2.3 Fan Header The number of fans in each platform may be different. Locations of the fan headers shall accommodate circulation of fresh air from the front of the chassis. The fan header shall be type MOLEX 22-23-2051 with pin out outlined below. Figure 4-4: FAN Header 4Pin(CN1,CN2,CN12) 4.2.4 CF Header 25 X 2 Pin header... -
Page 18: Pci Express Golden Finger
4.2.5 PCI Express Golden Finger Figure 4-6: PCI Express Slot 64Pin(GF1 ) 4.2.6 KB/MS Header Figure 4-7: KB/MS Connector 1x8Pin(CN28 ) -
Page 19: Lpt Header
4.2.7 LPT Header Figure 4-8: LPT Header 2x13Pin(CN27 ) 4.2.8 Console Connector Figure 4-9: RJ45 Connector(CN23 ), the default baud rate is 19200. -
Page 20: External Serial Port Header
4.2.9 External Serial Port Header Figure 4-10: External Serial Pin Header(CN20 ) 4.2.10 USB Connector Figure 4-11: USB Connector(CN24 ) -
Page 21: Lan Port
4.2.11 LAN Port LED status: GbE Link: Green (Left) FE Link: Amber (Left) Action Link: Green/Blink (Right) Figure 4-12: RJ45 for LAN Connectors (CN25,CN26,CN21 from Tolapai, CN22 from 82574L) Tolapai ‘s LAN LED issues notice: Link LED wasn’t work correctly and plan to fix on next version. 4.2.12 System Reset Header 2 X 1 Pin 2.54mm header Comment... -
Page 22: External Gpio Header
4.2.14 External GPIO Header Figure 4-15: External GPIO Header(CN29) 4.2.15 LED Header Figure 4-16: LED Header(CN17) -
Page 23: General-Purpose Io (Gpio) Assignments And Descriptions
4.3 General-Purpose IO (GPIO) Assignments and Descriptions 4.3.1 Tolapai GPIO Table 4-2: Tolapai GPIO Definition Signals Name I/O Type Tolerance Function Comments GPIO0 3.3V GPIO1 3.3V GP2_PIRQE# 3.3V GP3_PIRQF# 3.3V GP4_PIRQG# 3.3V GP5_PIRQH# 3.3V GPIO6 3.3V GPIO7 3.3V GPIO8 3.3V GPIO9 3.3V GPIO10... -
Page 24: Super I/O Gpio
4.3.2 Super I/O GPIO Table 4-3: Super I/O GPIO Definition Signals Name I/O Type Tolerance Function Comments GP10 Port80 LED GP11 Port80 LED GP12 Port80 LED GP13 Port80 LED GP14 Port80 LED GP15 Port80 LED GP16 Port80 LED GP17 Port80 LED GP20 GP21/SCL GP22/SDA... - Page 25 Table: Memory compatibility test table Brand Size Speed Type ECC REG Vendor PN Memory chip Criteria Measurement Judgment 7XE22 DDR2 NO NO 78.A2G75.AT5 PASS PASS D9HNQ 8AE12 D9HNQ Apacer DDR2 NO NO 78.02G75.AT2 PASS PASS 7XE22 D9HNQ 512MB DDR2 NO NO 76.9325G.B12 0702SP TAIWAN PASS...