Table of Contents
Advertisement
0
37
Chapter 5 Appendix
Maintenance and Usage Precautions
Maintenance
Camera and sensor unit cleaning
ˎ Do not directly touch the surface of the lenses.
ˎ
ˎ Use a blower or a soft, clean cloth to lightly wipe
ˎ
the lenses if they are dirty.
ˎ Never use organic solvents such as benzene or
ˎ
thinners to clean the lenses.
ˎ Use a soft, dry cloth to clean the external
ˎ
surfaces of the product. Stubborn stains can be
removed using a soft cloth dampened with a
small quantity of detergent solution, then wipe
dry.
ˎ Do not use alcohol, thinner, benzine, etc. when
ˎ
cleaning the exterior of the product. Doing
so can degrade the materials and cause the
coating to come off.
ˎ When you use a chemical cloth, follow its
ˎ
instructions.
ˎ Do not sprinkle volatile matter such as pesticide
ˎ
over the product nor allow rubber or vinyl to
come in contact with the product for a long
period of time. Doing so may damage the finish.
ˎ Make sure to keep the white receptor surface
ˎ
clean in order for the light sensor to function
correctly. If the surface becomes dirty with oil,
water or fingerprints, wipe them off right away
with a soft cloth.
Drone maintenance
Maintaining the drone daily helps reduce trouble
during flight. Refer to the drone manual or
manufacturer's website for information on drone
maintenance.
Precautions
Operating or storage location
ˎ Check the drone manual for information on
ˎ
drone usage and storage.
ˎ Use or store the product in the following
ˎ
environments.
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: -20 °C to +60 °C
(-4 °F to 140 °F)
Operating humidity: 20% to 80%
(no condensation allowed)
Storage humidity: 20% to 80%
(no condensation allowed)
ˎ Avoid operating or storing the product in the
ˎ
following locations.
– Extremely hot or cold places (Follow the
above usage and storage temperatures of
the product. Make sure to check the drone
manual for further information.)
– Exposed to direct sunlight for a long time,
or close to heating equipment (e.g., near
heaters)
– Close to sources of strong magnetism
– Close to sources of powerful electromagnetic
radiation, such as radios or TV transmitters
– Locations subject to strong vibration or shock
– Locations subject to steam or high humidity
– Locations exposed to rain
– Locations where radiation or X-rays are
emitted
– Near the outdoor unit of an air conditioner or
any other place where drastic temperature
changes may occur
– Locations subject to strong wind
– Locations where corrosive gas or flammable
gas is emitted, or where salt damage may
occur
ˎ Avoid dusty or sandy areas as takeoff locations
ˎ
whenever possible.
ˎ Never leave the lens pointed toward a strong
ˎ
light source, such as the sun.
Ventilation
To prevent heat buildup, do not block air
circulation around the product.
Transportation
ˎ To protect the lens, make sure to attach the lens
ˎ
caps during transportation.
ˎ When carrying the product, make sure to
ˎ
disconnect the mobile battery cable from
the camera and leave the power supply
disconnected.
ˎ When transporting the product, repack it as
ˎ
originally packed at the factory or in materials
equal in quality.
ˎ Carrying the product with the connecting cable
ˎ
or mobile battery cable connected can damage
the terminals or cable.
microSD cards
ˎ Data on the microSD card may be damaged
ˎ
or deleted in the following cases. Sony is not
responsible for compensation for damage or
lost earnings due to damage or loss of data.
– If you remove the microSD card from the
product or turn off the power while the
microSD card is being accessed.
– If the microSD card is subject to shock.
– When the lifetime of the microSD card
expires. (Lifetime may shorten significantly,
depending on its use.)
– If the microSD card is not set or inserted
properly.
– If the microSD card is used in environments
exposed to static electricity or electrical noise.
ˎ We recommend backing up important data to
ˎ
your computer's hard disk, for example.
ˎ Do not affix labels, for example, onto microSD
ˎ
cards.
ˎ Do not touch the terminals or bring them into
ˎ
contact with metal objects.
ˎ Do not bend, drop, or subject microSD cards to
ˎ
excessive shocks.
ˎ Do not dismantle or modify microSD cards.
ˎ
ˎ Do not wet microSD cards.
ˎ
ˎ Keep microSD cards away from small children to
ˎ
prevent accidental swallowing.
ˎ Do not insert microSD cards of unsupported
ˎ
sizes into the microSD card slot, as doing so may
result in malfunction.
ˎ Avoid use and storage in the following
ˎ
environments.
– High-temperature locations, such as the
inside of an automobile parked in the sun.
– Locations exposed to direct sunlight.
– Locations with excessive humidity or
corrosive materials present.
Precautions on disposal and transfer
When transferring possession of a microSD card,
use data erasure software on a computer, for
example, to completely erase the data. When
disposing of a microSD card, we recommend
physically destroying the microSD card as well.
Advertisement
Table of Contents
