ETC Desire D22 User Manual
Hide thumbs Also See for Desire D22:

Advertisement

Quick Links

ETC Installation Guide
®
Desire
Series D22

Introduction

The Desire D22 is designed for indoor installations and has a rugged die-cast
enclosure, steel mounting yoke, and noise-free, fan-less operation.
The D22 can be pipe mounted with a C-clamp, canopy mounted, or track
mounted. Mounting accessories are available. Contact ETC Customer Service
for assistance; contact information is located at the bottom of this page.
Portable
For information about the operation of the D22 Desire Series, see the
Series by ETC D22, D40, D40XT, D60 User Manual
for download at etcconnect.com.
CAUTION: Do not attempt to install or use a fixture until you read
WARNING:
Canopy Mount
and understand the installation instructions and safety
labels.
This fixture must be installed by a qualified electrician
in accordance with all national and local electrical and
construction codes and regulations.
Corporate Headquarters
Service (Americas)
service@etcconnect.com
London, UK
Tel +44 (0)20 8896 1000
Rome, IT
Tel +39 (06) 32 111 683
Holzkirchen, DE
Tel +49 (80 24) 47 00-0
Hong Kong
Tel +852 2799 1220
Web:
etcconnect.com
© 2016 Electronic Theatre Controls, Inc.
Specifications subject to change.
7411M2100
Rev D
Released 2016-12
Middleton, Wisconsin, USA
Service: (UK)
Service: (UK)

Service: (DE)
Service: (Asia)
ETC intends this document to be provided in its entirety.
Track Mount
. ETC manuals are available
Tel +608 831 4116
service@etceurope.com
service@etceurope.com
techserv-hoki@etcconnect.com
service@etcasia.com
Product information and
Desire

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Desire D22 and is the answer not in the manual?

Questions and answers

Summary of Contents for ETC Desire D22

  • Page 1 Desire Series D22 Introduction The Desire D22 is designed for indoor installations and has a rugged die-cast enclosure, steel mounting yoke, and noise-free, fan-less operation. The D22 can be pipe mounted with a C-clamp, canopy mounted, or track mounted. Mounting accessories are available. Contact ETC Customer Service for assistance;...
  • Page 2: Specifications

    A termination board is incorporated into the mounting plate for installation onto a voltage-separated junction box (junction box provided by others, voltage barrier provided by ETC) and provides termination for control wiring: • Connection of the D22 data cable to a provided screw-down connector, which is pre-wired at the factory.
  • Page 3 Ensure the main power supply is off before installing or wiring a fixture. The Desire D22 Portable fixture has a permanently installed power cord with 3-prong Edison connector. Region-specific connectors are available. Contact ETC for available options. The Canopy Mount fixture is provided with power and data wired to the canopy and should be terminated in a voltage- separated junction box (provided by others).
  • Page 4 120-ohm resistor. • The Portable fixture is self-terminated. • The Track Mount fixture is terminated with a DataTrack DMX Term Block (ETC part number 7066A1030). • The Canopy Mount fixture is terminated on the Termination board inside the canopy.
  • Page 5 Canopy assembly (not provided) CAUTION: Separate the line voltage from the data side in the junction box. Install the voltage barrier provided by ETC. DMX/RDM Cable Installation Terminate DMX/RDM input from the From a DMX/RDM source control source to the junction box.
  • Page 6 ETC Installation Guide Desire D22 If using Category 5: Cat5 Cable Preparation for a: See the IDC Termination Setup Guide instructions to prepare and terminate Category 5 for DMX/RDM input cable to the insulation displacement connector. b: Install the IDC connector with wires terminated to the DMX/RDM Input receptacle on the termination board.
  • Page 7 ETC Installation Guide Desire D22 Canopy Fixture Installation Installation hook and Strip the fixture’s power wires back bracket 1/2 inch (13 mm). Using the hole in the mounting bracket, hang the canopy on the installation hook. Following the label on the mounting plate, attach the power wires to the power block.
  • Page 8 20 fixtures on a single run. Initial Power Up Control and configuration of the Desire D22 can be achieved over a DMX/RDM control network, or directly from a connected computer running appropriate software. When controlling the D22 directly from a PC, a Gadget II Interface or DMX/RDM gateway is required.

This manual is also suitable for:

Desire series

Table of Contents