Coolaroo AutoSun Custom Made Instruction Manual page 16

POWERING UP YOUR SOLAR
POWERED SOLAR SHADE
YOUR SOLAR POWERED EXTERIOR SUN SHADE COMES FROM
THE FACTORY AT COOLAROO WITH AN INITIAL CHARGE,
PLEASE INSTALL YOUR SHADE PROMPTLY OR PLACE THE
SOLAR PANEL, CONNECTED TO THE BATTERY AND FACING
THE SUN SO IT DOES NOT LOSE ITS CHARGE.
WARNING: Do not charge at a temperature above 70 degrees C.
1. CHARGING BATTERY WITH OPTIONAL CHARGER (SOLD
SEPARATELY)
• Charge duration: 210 min. max. 2 charges by year max.
• Never leave a battery in a discharged condition.
• No not open or pierce the battery.
• Do not put the battery into a fire, risk of explosion. Keep
away (1m minimum) from from all types of flames, sparks or
incandescent material.
• Do not create a short circuit on the battery terminals: danger
of burns and explosion.
• The battery must be sheltered from the rain (IP X4).
• The battery must be accessible in order to carry out possible
recharging (see instruction sheet 5055192).
• Suitable substrates for sticking: runners and box in aluminium,
box in PVC (remove the protective films).The surfaces to be
glued must be dry and clean.
• The ambient temperature when gluing should be between
20°C (68° F) and 38°C (100.4° F).
• We recommend users run industrial tests in exactly the same
conditions as those of the intended application and thereby
ascertain that our product satisfies its requirements. If in
doubt, opt for the screwing solution.
• The battery must be replaced by a professional with an
identical model.
• Do not put in the dustbin, this is a recyclable product.
16
the settings for the direction of rotation and end limits are retained. Per
tion 2.1c then operation 3 to programme a new individual controller.
9. Complete cancelling of programming
- Press the "PROG" key of the battery pack more than 12 seconds. The motor w
- Press the "PROG" key of the battery pack more than 7 sec
run 3 times in one direction and then in the other. The operation is completed.
for in one direction and then in the other. The operation is
The motor returns to its original set up, with no transmitter programme
The motor doesn't have any transmitter programmed
in the memory. Redo the complete programming procedure for the mot
the settings for the direction of rotation and end limi
(direction of rotation, end limits and control points).
tion 2.1c then operation 3 to programme a new indiv
10. Battery protection against excessive discharge
- Press the "PROG" key of the battery pack more than 12 se
Before each lifting or lowering of the shutter, the motor checks the volta
run 3 times in one direction and then in the other. The ope
If the voltage is below 11.5V: The motor will pause at the beginning of e
The motor returns to its original set up, with no trans
in the memory. Redo the complete programming proc
If the voltage is below 10V: The receiver won't accept any commands.
(direction of rotation, end limits and control points).
In these two cases, use the emergency charger in order to per
motor will return to normal only if the battery voltage goes a
Before each lifting or lowering of the shutter, the moto
- Do not recharge other battery types besides those provided for th
If the voltage is below 11.5V: The motor will pause at
battery - réf.9014734), there is a risk of explosion.
- Keep away (1m minimum) from from all types of flames, sparks o
If the voltage is below 10V: The receiver won't accept
- Do not open the charger, risk of electric shock.
- Do not use the charger if the cable is damaged.
- Do not cover during use.
LED
1
1- Connect the charger to the mains supply. The two-colour LED (green
2- Open the battery cover.
3- Disconnect the battery from the motor.
4- Connect the charger to the battery. The LED changes colour from gre
1- Connect the charger to the mains supply. The two-c
- Maximum charging time for 1 battery: 3 hours 30 min.
2- Open the battery cover.
- 2 charges / year max. 3- Disconnect the battery from the motor.
4- Connect the charger to the battery. The LED change
- Minimum charging time to be able to open the shutter (with a ba
210 min.
5- Charging is finished when the LED changes colour back to green. Disconn
6- Reconnect the battery to the motor.
5- Charging is finished when the LED changes colour back
7- Replace the battery cover.
6- Reconnect the battery to the motor.
7- Replace the battery cover.
11. Battery pack replacement
1- Disconnect the battery pack, the motor (a) and the solar panel
Replace the battery pack
2-
1- Disconnect the battery pack, the motor (a) and
Charge the new pack. Connect the new pack to the motor and
3- 2-
3-
12
12
- Do not recharge other battery typ
battery - réf.9014734), there is a
- Keep away (1m minimum) from f
- Do not open the charger, risk of e
8. Cancelling all the programmed trans
- Do not use the charger if the cab
- Do not cover during use.
LED
1
9. Complete cancelling of programming
Fig. 1
only be closed by pressing several times on
1- Connect the charger to the mains sup
2- Open the battery cover.
3- Disconnect the battery from the moto
10. Battery protection against excessive
4- Connect the charger to the battery. T
- Maximum charging time for 1 bat
- 2 charges / year max. only be closed by pressin
- Minimum charging time to be abl
In these two cases, use the emergency charge
motor will return to normal only if the batter
- Do not recharge other battery types besides tho
battery - réf.9014734), there is a risk of explosio
- Keep away (1m minimum) from from all types o
1
- Do not open the charger, risk of electric shock.
- Do not use the charger if the cable is damaged.
210 min.
- Do not cover during use.
2
LED
5- Charging is finished when the LED chan
2
6- Reconnect the battery to the motor.
Fig. 2
7- Replace the battery cover.
1
11. Battery pack replacemen
1- Disconnect the battery pack, the m
Replace the battery pack
2-
Charge the new pack. Connect th
3-
- Maximum charging time for 1 battery: 3 hours
- 2 charges / year max.
12
- Minimum charging time to be able to open the
5
5
210 min.
Fig. 3
11. Battery pack replacement
with an identical model
(c).
Replace the battery pack
(c).
Charge the new pack. Connect the new pack t
2
5
1
1
2
2
with
(c).
.
with an identical m