Table of Contents
Advertisement
8
£ng/ish
l/ert/ca/ batch freezer
Check that the machine is supplied with the lid [5] and that the beater [6] is correctly fixed inside the cylinder with its knob
[7], The bigger models are supplied with a tilting blade [23] and its fixing knob [24],
Also make sure that in the packing there are the device's following parts:
the extraction door's chute [9];
basin support [10] complete with storage cup [11];
tube-brush [12] and ice cream's blade [13];
all the technical documentation (in addition to this handbook): the Technical Handbook, the CE's Conformity Certifi-
cation and Electrical Test's Schedule.
5.2
Device's parts reassembling
A
REASSEMBLY MUST BE CARRIED OUT BEFORE CONNECTING MACHINE TO ELECTRIC OUTLET.
Bring lever [8] in operative position (perpendicular to the extraction door) by loosening and then tightening bolt [39].
Use the 3mm alien key [40] provided.
if the chute [9] is furnished dismantled, install it below the extraction door [14] fixing it at the frontal panel through the
hand screw [15];
install the basin support [10] fixing it at the frontal panel through the hand screws [16].
Note:
The machine will not operate without the protection flap since the flap includes a safety magnetic contact and
its magnet.
5.3
Electrical connection
A
THE SUPPLY VOLTAGE REQUIRED BY THE DEVICE IS HIGH, SO, IT IS PARTICULARLY DANGEROUS.
THE WORKS ON THE ELECTRICAL SUPPLY CIRCUITS MUST BE MADE WORKMANLIKE BY QUALIFIED
STAFF.
A
THE ELECTRICAL SAFETY OF THIS AUTOMATIC CREAM-WHIPPER IS
REACHED ONLY WHEN THE SAME IS CORRECTLY CONNECTED, BY
QUALIFIED AND CERTIFIED PERSONNEL, TO AN EFFICIENT EARTH-
ING SYSTEM, MADE AS PROVIDED FOR IN FORCE SAFETY REGULA-
TIONS.
The manufacturer must not be considered responsible for eventual damages
caused by an inadequate electric plant or earthing.
All the device's electrical features required for the system's proportioning are reported
on the Technical Data Plate and on the Technical Handbook.
FOR THE PREPARATION OF THE ELECTRICAL PLANT WHICH SUPPLIES THE DEVICE, IT IS COMPUL-
SORY TO FOLLOW THE PRESCRIPTIVE STANDARDS IN FORCE. IN PARTICULAR:
Eng/ish
Operat/ng mtractions
21
Maintenance during the components disassembling
Check the integrity of gaskets (indicated with [G] in the figure) and substitute those that
are deteriorated.
Use exclusively original, compatible with food, rubber gaskets. The spare bag
contains a complete series of gaskets approved by the manufacturer.
To correctly replace the gaskets it is necessary to:
remove the old gaskets by using a sharp tool, possibly non-metallic, paying attention not to scratch the seating of the
gaskets themselves;
clean the seatings and the gaskets from any kind of grease before inserting the new gaskets.
Check that the plastic runners' scraping edges are not scratched or dented, and that
.
A A
r A
the side runners are not worn as shown in the picture. If they appear worn, replace
7
them.
A thorough scraping of the cylinder will provide BEST PERFORMANCE
by the batch freezer and HIGH QUALITY ICE-CREAM. Therefore we
recommend to frequently replace plastic runners (at least once every
THREE MONTHS).
A yearly preventive replacement of all wearing parts and all gaskets is recommended. We suggest you to always keep a
spare supply: to order it, refer to the Spares Section contained in the Technical Handbook.
8.2
Check of safety devices
Check proper functioning of all safety devices every three months. Do so by following this procedure:
if necessary stop the device by pressing the ON/OFF Pushbutton [K1]. Rotate the Main Breaker in "0" position. When
Main Breaker is correctly working, the POWER'S indicator [Z1] must be off.
open the lid and remove the beater;
check that protection grill [3] is intact and firmly fixed;
close the lid and take the Main Breaker in "1" position;
press the ON/OFF Pushbutton [K1] and, afterwards, the BEATING Pushbutton [K5] (the beater's shaft will start). Then
open the lid. Provided that the lid's magnetic contact is correctly working, the beater's shaft will stop immediately and
the Display will show "oo" (two small squares).
If the machine's functioning is as described, the safety devices are efficient.
A
THE MACHINE MUST NOT BE USED IF ONE OR MORE OF THE SAFETY DEVICES SHOULD RESULT
DAMAGED OR MALFUNCTIONING!
Hide quick links:
Advertisement
Table of Contents
