Table of Contents
Advertisement
CONFIGURING THE GATEWAY
Powering on the gateway
Before powering on the gateway, familiarize yourself with the safety aspects of the
connections (see page 5).
1. Connect the cord from the supplied power supply unit to the port labeled POWER
on the rear panel of the gateway (see page 8).
WARNING: Use only the power supply unit supplied with the gateway. Using a
different power supply unit can damage the gateway and void the warranty.
2. Connect the other end of the power supply unit's cord to a working power
outlet. The outlet should not be controlled by a wall switch to avoid someone
unknowingly turning off power to the outlet. The gateway powers on
automatically. The Power LED on the front panel goes ON and the other front
panel LEDs show the gateway's status (see page 7).
Rebooting or resetting the gateway
If required, you can use the RESET button on the gateway rear panel to reboot (power
cycle) the gateway, or reset the gateway to its original factory default settings.
Rebooting the gateway
To reboot the gateway and keep any customized overrides you made to the default
settings:
1. Leave power cord connected to the gateway.
2. Press the RESET button on the gateway rear panel.
3. Wait for the gateway to reboot.
Restoring factory defaults
When you restore the gateway to its factory default settings, you will remove all
overrides you made to the configuration, including changes to the default login user
name, password, and IP address.
To restore factory default settings using the RESET button:
1. Leave power plugged into the gateway.
2. Press and hold the RESET button on the gateway rear panel until the POWER LED
starts to flash (this may take up to 15 seconds), then release the RESET button.
3. Wait for the gateway to reboot with factory default settings.
Configuring your wireless connection
The gateway ships with wireless LAN security set by default. See the product label on
your gateway for the factory security settings.
Note: You must set up your computer and other client devices to work with the
security settings on the gateway. Refer to the documentation for your client device for
instructions on setting security. On most computer systems you only need to select
the network name (SSID) device and enter the encryption key. If your computer or
client device supports Wi-Fi Alliance WPS (Wireless Protected Setup), activate WPS on
your computer or client device and the gateway simultaneously to easily set up your
system security.
If you need to modify the gateway's default wireless security settings, or if you want
to configure any other wireless LAN settings, refer to the following instructions.
X5001 USER GUIDE - 501-3327100
Default Wi-Fi Settings
Model: X5001
Power: 12V
5.5A
Network Name (SSID):
Part No: E8263327100
Made in China
XFSETUP-XXXX
Contains FCC WiFi modules:
2.4GHz - FCC ID: PGR2G4360M / 5GHz - FCC ID: PGR5G4360M
Password:
This device complies with part 15 of the FCC rules.
XXXXXXXXXXXXXXX
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Manufactured February 2016
Complies with 21 CFR Chapter 1, subchapter J.
123456s3113
Manufactured by ARRIS, 3701 FAU Boulevard,
Suite 200, Boca Raton, FL 33431 USA
EPON MAC: 00:00:00:00:00:00
PROPERTY OF COMCAST. NOT FOR RESALE. REMOVING
123456s3113
THIS STICKER OR TAMPERING WITH THIS EQUIPMENT IS A
VIOLATION OF FEDERAL AND STATE LAW. THIS EQUIPMENT
MUST BE SURRENDERED TO COMCAST UPON DEMAND OR
eMTA MAC: 00:00:00:00:00:00
DISCONNECTION OF SERVICE; IF NOT, A FEE OF UP TO
$500
AND
LEGAL
PENALTIES
CAN
RESULT.
FOR
123456s3113
INFORMATION ON HOW TO RETURN CALL 1-800-266-2278.
E222159
WAN MAC: 00:00:00:00:00:00
123456s33
Serial No: XXXX00000000
I.T.E
Mfr S/N: XXXXXXXXXXXXXXXX
35ZB
WPS PIN: XXXXXXXXXX
Need help?
http://xfinity.com/internethelp
15
Hide quick links:
Advertisement
Table of Contents
