Related Manuals for J&M SpeedTender LC290
Summary of Contents for J&M SpeedTender LC290
- Page 1 Manual p e e d e n d e r MODEL O P E R A T O R ’ S M A N U A L J&M Manufacturing Co, Inc 284 Railroad Street - P.O. Box 547 | Fort Recovery, OH 45846 | Ph: (419) 375-2376 | Fax: (419) 375-2708 www.jm-inc.com...
-
Page 3: Table Of Contents
Table Of Contents 4 ..................To the Dealer 5 . -
Page 4: To The Dealer
To the Dealer TO THE DEALER Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists are completed before releasing equipment to the owner. The dealer must complete the Warranty Registration found on the Dealer Portal website located at dealer.jm-inc.com and return it to J&M Mfg. -
Page 5: General Information
General Information TO THE OWNER: The purpose of this manual is to assist you in operating and maintaining your seed tender in a safe manner. Read it carefully. It furnishes information and instructions that will help you achieve years of dependable performance and help maintain safe operating conditions. If this machine is used by an employee or is loaned or rented, make certain that the operator(s), prior to operating: 1. -
Page 6: Safety Rules
Safety Rules Understand that your safety and the safety of other persons are measured by how you service and operate this machine. Know the positions and functions of all controls before you try to operate them. Make sure to check all controls in a safe area before starting your work. -
Page 7: Specifications
Specifications Capacity Weight Tongue Weight Unloading (Total) (Empty) (Loaded) Conveyor Rate Conveyor Axles Engine 290 Seed 6,100 lbs. 1,650 lbs. 22’ Long, 8” 30 Bushels/ 49’ (Front to Two (2), 7,000 lb. Torsion-Flex 13 HP Honda Motor Units Tube Conveyor Minute Rear Swing) Axles with Electric Brakes... -
Page 8: Decals
Decals Description Part No. SpeedTender Advanced Seed Delivery JM0040057 LC Series Decal JM0049466 J&M Oval Decal (Large) 9-1/2” x 15” JM0015151 Warning, High Pressure Fluid Hazard Decal 4” x 4” JM0010163 Warning, Keep Open Flames Away Decal JM0014983 Important, Disconnect Power To Scale Decal JM0040056 Warning, Always Use Safety Chains Decal JM0014995... - Page 9 Decals Description Part No. 15 LC290 Conveyor Side Stripe JM0050432 16 LC290 Opposite Conveyor Side Stripe JM0050433 17 2” x 18” Red and White Reflective Strip JM0015079 18 Grease Point Decal JM0040055 19 Warning, Falling Or Lowering Decal JM0014992 20 Warning, Tire Wheel or Lug Nut Failure Decal JM0014996 21 Warning, Pinch Point Decal JM0014994...
-
Page 10: Bolt Torque Specifications
Bolt Torque Specifications Always tighten hardware to these values unless a different torque or tightening procedure is listed for specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware. Make sure fastener threads are clean and you start thread engagement properly. -
Page 11: Operations
Operations Preparing the Towing Vehicle Before towing the SpeedTender, refer to towing vehicle’s operator’s manual for information concerning hitch capacities, hitch adjustments, and tire inflation. Towing vehicle must be equipped with proper electric braking components. NOTE: The SpeedTender is equipped with LED lights. The towing vehicle may require a flasher upgrade for lights to operate properly. - Page 12 Operations Hydraulic Power Unit Operation Ensure all fittings and hardware are in proper operating condition. Replace if worn or broken. Check engine fluid levels and sight gauge on reservoir for proper operating levels. Slide the fuel shut-off lever to the “ON” position. Slide choke to the “ON”...
- Page 13 Operations Field Operation WARNING: The SpeedTender must be hooked to the towing vehicle during loading and unloading. Position the SpeedTender next to the planter/drill so the conveyor will reach the planter box. Release the ratchet strap from the conveyor. Start the hydraulic power unit and increase throttle speed. Allow hydraulic fluid to warm up. Raise the conveyor off the conveyor rest using the handheld control.
- Page 14 Operations Use the handheld controller or wireless remote to start the conveyor. Fill the planter/drill to desired level then repeat. NOTE: Adjusting engine throttle will regulate conveyor speed. Close door on SpeedTender before the last planter seed box is full so you can completely empty collapsible hopper and conveyor. 10.
- Page 15 Operations Lock collapsible hopper in the up position. 10. Position the wagon or bulk seed container over the collapsible hopper. 11. Use the handheld controller or wireless remote to start the conveyor. 12. Fill the SpeedTender to desired level. WARNING: Fill the front compartment first to help prevent the chance of flipping. 13.
- Page 16 Operations 12. Position conveyor above conveyor rest and lower to allow its full weight on the conveyor rest. 13. Tighten strap and ensure it is secured. 14. Ensure the collapsible hopper is in the down position and apply the vinyl hopper cover. 15.
-
Page 17: General Service
General Service Daily Service (5 -10 Hours of Use) NOTE: J&M recommends the following service to be performed daily (every 5-10 hours of use) Grease the conveyor bearings every 10 hours. Use only two pumps of grease per bearing. NOTE: Excess lubrication of these bearings will result in premature failure. NOTE: The conveyor has four bearing that need greased (two at each end). -
Page 18: Hydraulic Power Service
General Service Removing From Storage Grease the conveyor bearings. Use only two pumps of grease per bearing. NOTE: Excess lubrication of these bearings will result in premature failure. NOTE: The conveyor has four bearings that need greased (two at each end). See “Conveyor Service” on page 21. Grease pivot points on boom arm. -
Page 19: Tire Service
Tire Service Tire Pressure The following is to be used as a general guide for tire inflation. Figures can vary depending on specific brand of tire used. It is important that tires are inspected before and after unit is loaded. Start with the minimum pressure indicated. The tire should stand up with no side wall buckling or distress as tire rolls. -
Page 20: Wheel Bearing Service
Wheel Bearing Service Clean, inspect, and repack the wheel bearings every 12 months or 12,000 miles. Use a number 2 wheel bearing grease to repack the bearings. Bearing Inspection and Service: Jack up SpeedTender. Remove wheel lug nuts. Remove wheel from hub. Remove grease cap. -
Page 21: Conveyor Service
Conveyor Service Grease Conveyor Bearings Grease the conveyor bearings every 10 hours of operation and before storage. Use only two pumps of grease per bearing. NOTE: Excess lubrication of these bearings will result in premature failure. NOTE: The conveyor has four bearings that need grease (two at each end). Grease Point Grease Swing Arm Grease pivot points on boom arm every 50 hours and before storage. - Page 22 Conveyor Service Conveyor belt must run in the center of the pulley at both the discharge end and the collapsible hopper end. Failure to do so will lead to unnecessary wear and shortening of belt life. We recommend that you check your belt for proper tracking every 10 hours of use and before every season.
- Page 23 Conveyor Service Adjusting Conveyor Belt Tracking Loosen, but do not remove, the four bolts on the two bearing mounting plates located at the collapsible hopper end of the conveyor (as shown in the picture below). NOTE: Only adjust conveyor in normal position, do not adjust in self-fill position. Operate the conveyor at a slow speed.
-
Page 24: Brakes Service
Brakes Service The SpeedTender is equipped with electric brakes. They need to be inspected and serviced immediately if a loss of performance is experienced. You need to service your SpeedTender brakes at least once a year with normal use. How to use your electric brakes properly: Your SpeedTender brakes are designed to work in synchronization with your tow vehicle brakes. - Page 25 Brakes Service Brake Shoe and Lining Inspection: A simple visual inspection of your brake linings will tell if they are usable. Replacement is necessary if the lining is worn (to within 1/16” or less), contaminated with grease or oil, or abnormally scored or gouged. Hairline heat cracks are normal in bonded linings and should not be cause for concern.
- Page 26 Brakes Service Voltage in the system should begin at 0 volts. As the controller bar is slowly actuated, the voltage should gradually increase to approximately 12 volts, which is referred to as modulation. No modulation means when the controller begins to apply voltage to brakes, it applies an immediate high voltage, which causes the brakes to apply instantaneous maximum power.
-
Page 27: Troubleshooting
Troubleshooting Problems Solutions Unit sways during travel a. Check tire pressure. b. Check tow vehicle for loosened hitch parts. c. Check tow vehicle’s hitch height. d. Reduce towing speed. e. Check wheel lug nuts. f. Check wheel bearings for adjustment (see ”Wheel Bearing Service” on page 20). Tires show excessive wear a. - Page 28 Troubleshooting Problems Solutions Excessive wear to belt edge - Rubber skirting is a. Replace rubber skirting. worn or out of place b. Adjust rubber skirting. Swing arm will not move up or down - Engine RPM a. Increase engine RPM. slow Swing arm will not move up or down - Hydraulic a.
-
Page 29: Controls
Controls Description Part No. Onboard Intercomp Controller (WC3-D) JM0041055 Intercomp Remote JM0041056 Onboard Controller (LC Series and c450) JM0051370 5 Switch Yellow Remote with 44’ Cord (SPT-AF2) JM0014991 Note: When replacing Conveyor On/Off Avery Weigh-Tronix 640XL Indicator (640XLI) JM0007293 switch, both JM0028114 & JM0037125 Wireless J&M Mega Remote with Green Button (SPT-WC1-D) JM0036049 will work. -
Page 30: Throttle Control
Throttle Control Description Part No. 1 Adapter for Kar-Tech Receiver - Throttler Control (113991) JM0038428 2 #10-24 x 1” Z Round Head Phillips Screw JM0037646 3 #10-24 Z Nylon Locking Hex Nut JM0016030 4 RMC 3500 Linear Motor JM0038427 5 Throttle Control Motor Tube Clamp JM0038430 6 Cable Coupler w/ Clip for Seed Tender Throttle Control JM0041943... -
Page 31: Valve Wiring
Valve Wiring Connector Letter Function Conveyor Swing Front Conveyor Swing Rear Conveyor Up Conveyor Down • Use a good set of Allen wrenches when changing orifices. Rear Door Up Front Door Down • The cartridge should be tightened with 25 ft-lbs of torque. Power Front Door Up •... -
Page 32: Lights And Wiring
Lights and Wiring This table will be used for the following section, Lights and Wiring, on Pages 32-35: Description Part No. 2-1/2” Red Round LED Light/Reflector Assembly (RRLA1) JM0001905 2-1/2” Red Round LED Light/Reflector (RRLR1) JM0001901 Round Grommet for LED 2-1/2” Light/Reflector JM0001902 2-1/2”... - Page 33 Lights and Wiring ST Main Harness (419-475) (JM0033700) To Rear Top To A-Frame or Harness Gooseneck Harness To Right Front To Rear Brake Light Marker Right Round Lights Red Marker To Electric Brakes Light To Onboard To Scale Box Valve Bank Controller Indicator Power...
- Page 34 Lights and Wiring ST Front Chassis Wiring Harness (419-385) (JM0019963) White 3” 30” 8” 3” To Front Top Harness 43” 65” To Front Lower Marker Light To Front Lower Marker Light ST Front Top Lights Harness (419-380) (JM0020364) White 101” 54”...
- Page 35 Lights and Wiring V-Belt A-Frame 7-Way Trailer Connection (JM0046142) V-Belt Gooseneck 7-Way Trailer Connection (JM0046143) 150” 167” 3” 16” To Main Harness Light Blue Tail Lights 12V Battery Dark Blue Brown Left Turn & Brake Right Turn & Brake Green Yellow Breakaway Switch with Cable (BAS-1) Electric Brakes...
-
Page 36: Intercomp Wiring
Intercomp Wiring JM0041056 JM0041055 16030 WC3-D PRINT START EXPORT HOLD TALC LIGHTS SCALE POSITION ENGINE MENU STOP SETUP TARE LEFT CONV RIGHT CONTROLS CONTROLS CONTROLS GROSS DOWN OPEN DOOR 1 DOOR 2 ROLL TARP DOWN SHIFT DOWN CLOSE OPEN CLOSE SHIFT Load Cells JM0041714... -
Page 37: Scale Display Box
Scale Display Box Description Part No. Chrome T-Handle Non-Locking JM0001911 Seed Tender Scale Box Door JM0046652 1/2” Shoulder Dia x 3/8” Shoulder Length x 3/8”-16 Socket Shoulder Bolt JM0009998 3/8”-16 Gr2 Z Centerlock Hex Nut JM0001512 Seed Tender Scale Box JM0046678 3/8”-16 x 1”... -
Page 38: A-Frame And Hitch
A-Frame and Hitch Description Part No. 5/8”-11 x 2” Gr8 Z Hex Bolt JM0001771 5/8”-11 Gr2 Z Centerlock Hex Nut JM0002146 Seed Tender - Chassis A-Frame Weldment JM0002481 5,000 lb Max Lift Capacity Jack (TWL-178T) JM0001480 1/4” x 3/4” Self Tapping Screw JM0001570 Breakaway Switch with Cable (BAS-1) JM0001843... -
Page 39: Gooseneck
Gooseneck 19 20 21 Description Part No. Breakaway Switch with Cable (BAS-1) JM0001843 Square Gooseneck Coupler Tube 30,000 LB CAP JM0007076 12,500 Lb Safety Chain (SCST375) JM0015061 Gooseneck Frame Weldment (290, 390) JM0029497 ST Cover Plate (4-11/16” x 7-1/2” x 4-3/4”) JM0034699 Jack Brace for ST Gooseneck JM0034697... -
Page 40: Hydraulic Jack
Hydraulic Jack Description Part No. WR Series Hydraulic Motor with Keyway and Pinhole (15100F30N6AAAAA) JM0010469 Seal Kit for 15100F30N6AAAAA WR Series Hydraulic Motor JM0042773 1/2” Male JIC x 1/2: Male NPT; Straight JM0015201 3/8” Shoulder Dia x 1-3/4” Shoulder Length x 5/16”-18 Socket Shoulder Bolt JM0033449 3/8”... -
Page 41: Brakes And Hub Assembly
Brakes and Hub Assembly 12 13 Description Part No. Rubber Plug for Dust Cap JM0039538 Dust Cap for EZ Grease (7,000lb) JM0035957 Aluminum Wheel Dust Cap JM0049437 9/16”-18 Conical Lugnut (4WS) (ST) JM0008525 9/16 RH 7/8 Hex 2.40 XL (Lug Nut to Aluminum Wheel) JM0044721 Spring Steel Retaining Clip JM0051458... -
Page 42: Chassis
Chassis... - Page 43 Chassis Description Part No. Front Driver Side Fender Mount (SpeedTender) JM0002339 Front Passenger Side Fender Mount (SpeedTender) JM0002336 Rear Passenger Side Fender Mount (SpeedTender) JM0002490 Rear Driver Side Fender Mount (SpeedTender) JM0002491 Two Wheel Diamond Plate Fender Weldment (71”) JM0005874 235-85-R16 Load Range E - 8 Bolt Tire JM0003232 Wheel Rim, 8 hole, 16”...
-
Page 44: Swing Arm
Swing Arm 18 14... - Page 45 Swing Arm Description Part No. 5/16”-18 x 2-1/2” Gr5 Z Hex Bolt JM0028310 5/16”-18 Gr2 Z Centerlock Hex Nut JM0002143 1-1/4” ID x 2” OD Bronze Washer JM0040435 1-1/4” x 1-1/2” x 2”LG Sleeve Composite Bearing JM0040288 Upper Boom Pivot Weldment JM0001605 1”-8 Gr5 Z Hex Jam Nut JM0001705...
-
Page 46: Conveyor
Conveyor Description Part No. 8” Tube Conveyor (22’ V-Guide Belt) (Complete) JM0040130 Conveyor Hopper Support Tube JM0040345 LC Series Seed Tender Collapsible Vinyl Hopper Cover JM0041070 LC Series Seed Tender Conveyor Hopper Tarp JM0041069 8” Tube Conveyor, V-Guide Weldment Lower Section JM0027363 Conveyor Support Stand JM0002212... -
Page 47: Conveyor Discharge End
Conveyor Discharge End 12 13 Description Part No. WR Series Hydraulic Motor with Keyway and Pinhole (15100F30N6AAAAA) JM0010469 Seal Kit for 15100F30N6AAAAA WR Series Hydraulic Motor JM0042773 Hydraulic Motor Mount (DMST375W) JM0002225 1/2” Shoulder Dia x 3/8” Shoulder Length x 3/8”-16 Socket Shoulder Bolt JM0009998 1/4”-20 x 3/4”... -
Page 48: Conveyor Idler End
Conveyor Idler End... - Page 49 Conveyor Idler End Description Part No. Conveyor Hopper Support Tube JM0040345 3/8”-16 x 1-1/4” Gr5 Z Carriage Bolt JM0001639 Conveyor Guard Weldment JM0002466 Inner Rubber Clamp-Hopper End 1-1/4” x 21-5/8” (1142158P) JM0002767 3/8”-16 x 1” Gr5 Z Carriage Bolt JM0001632 8”...
-
Page 50: Shell
Shell 12V Battery used 23 24... -
Page 51: Spare Tire Mount
Shell Description Part No. Window Seal 3/4 “S” Strip JM0000254 Standard Inspection Window JM0000255 3/8”-16 x 1” Z Flat Head Phillips Screw JM0015500 3” x 17-1/2” Auger Rest Guide Plate UHMW JM0024456 Conveyor/Auger Pin Latch JM0042768 3/8”-16 x 1” Gr5 Z SF Hex Bolt JM0002092 3/8”-16 Gr5 Z SF Hex Nut JM0002152... -
Page 52: Ladder
Ladder Description Part No. SpeedTender - Upper Ladder Assembly JM0002950 Gas Spring (15-1/4” Extended x 9-3/4” Retracted) (120 lbs) JM0001961 5/16”-18 Gr2 Z Centerlock Hex Nut JM0002143 3/8”-16 x 1” Gr5 Z Hex Bolt JM0001592 Ladder Brace (ST) JM0014959 3/8”-16 x 1” Gr5 Z SF Hex Bolt JM0002092 Seed Tender - Lower Ladder Assembly JM0002359... -
Page 53: Hydraulic Door
Hydraulic Door Description Part No. 1 1/2”-13 Gr2 Z Centerlock Hex Nut JM0001511 2 1/2”-13 x 1-1/2” Gr5 Z Hex Bolt JM0002100 3 1-1/2” Bore x 7” Stroke Hydraulic Cylinder (157HC) JM0002882 4 3/8”-16 x 1” Gr5 Z SF Hex Bolt JM0002092 5 3/8”-16 Gr2 Z Centerlock Hex Nut JM0001512... -
Page 54: Hydraulics Schematic For Aluminum Valve
Hydraulics Schematic for Aluminum Valve Swing Cylinder Rear Door Front Door Cylinder Cylinder Boom Cylinder... - Page 55 Hydraulics Schematic for Aluminum Valve Description Part No. 1/2” x 210” Hydraulic Hose 210inch8M3k-8G-8FJX-8G-8FJX JM0041443 1/2” Male JIC x 1/2” Male JIC; Straight JM0041452 1/2” Male JIC x 1/2: Male NPT; Straight JM0015201 WR Series Hydraulic Motor with Keyway and Pinhole (15100F30N6AAAAA) JM0010469 Seal Kit for 15100F30N6AAAAA WR Series Hydraulic Motor JM0042773...
-
Page 56: Hydraulics Schematic For Black Intercomp Valve
Hydraulics Schematic for Black Intercomp Valve Swing Cylinder Rear Door Front Door Cylinder Cylinder Boom Cylinder... - Page 57 Hydraulics Schematic for Black Intercomp Valve Description Part No. 1/2” x 210” Hydraulic Hose 210inch8M3k-8G-8FJX-8G-8FJX JM0041443 1/2” Male JIC x 1/2” Male JIC; Straight JM0041452 1/2” Male JIC x 1/2: Male NPT; Straight JM0015201 WR Series Hydraulic Motor with Keyway and Pinhole (15100F30N6AAAAA) JM0010469 Seal Kit for 15100F30N6AAAAA WR Series Hydraulic Motor JM0042773...
-
Page 58: Talc Applicator
Talc Applicator Description Part No. Chrome T-Handle Non-Locking JM0001911 17 Deg. Talc Box Door (Electric & Hydraulic Motor) JM0037237 1/2” Shoulder Dia x 3/8” Shoulder Length x 3/8”-16 Socket Shoulder Bolt JM0009998 3/8”-16 Gr5 Z SF Hex Nut JM0002152 3/8” ID, 1” OD Z Flat Washer JM0003061 2”... -
Page 59: Talc Hydraulics Schematic For Aluminum Valve
Talc Hydraulics Schematic for Aluminum Valve Hydraulic Motor Aluminum Valve Bank Conveyor Return Hose Flow Control To Conveyor Return Hose Description Part No. 3/8” Male JIC x 3/8” Male O-ring; Extra Long 90 Degree Elbow (6801-LL-06-06) JM0039050 3/8” Male JIC x 3/8” Male O-ring; 90 Degree Elbow (6801-06-06-NWO) JM0026121 White Drive Hydraulic Motor - 125032JL5C3AAAAA JM0042491... -
Page 60: Talc Hydraulics Schematic For Black Intercomp Valve
Talc Hydraulics Schematic for Black Intercomp Valve 13 14 Description Part No. 3/8” Male JIC x 3/8” Male ORB; Extra Long 90 Degree Elbow (6801-LL-06-06) JM0039050 3/8” Male JIC x 3/8” Male ORB; 90 Degree Elbow JM0026121 White Drive Hydraulic Motor - 125032JL5C3AAAAA JM0042491 1/4”... -
Page 61: Spring Return
Spring Return Description Part No. Spring Return Housing for Seed Tender and Gravity Box Roll Tarp JM0002446 1/4”-20 Gr5 Z SF Hex Nut JM0001630 Spring Return Spring JM0000207 1/4”-20 x 3/4” Gr5 Z SF Hex Bolt JM0001642 3/8”-16 x 3” Gr5 Z Hex Bolt JM0001666 1-1/4”... -
Page 62: Roll Tarp
Roll Tarp... - Page 63 Roll Tarp Description Part No. Tightening Lip x 145-1/2” (290) JM0007039 9’6” x 11’7” Tarp with Rivets (290) JM0007020 3/16” Cable x 148” (290) JM0041578 92-1/4” Arched Tarp Bows (270, 290, 390) JM0010073 Tarp Stop Bracket (TSB-1) JM0000187 Spring Return Cable (Seed Tender and Gravity Boxes) JM0010307 Spring Return Assembly for Seed Tender (ST375TSW) JM0002437...